Home 
Home Search search Menu menu Not logged in - Login | Register
> Barthol

Profile Topics Posts
Posts by Barthol
67 postsShowing posts 1-40 of 67

Brakes > rear brakes draging (10 replies - 4057 views)

Hi Nigel My Bad, you are right, I will make a photo from the actual assembly later today. Thanks a lot for your help. BR Kim ...   06-18-2015 06:50 am

Brakes > rear brakes draging (10 replies - 4057 views)

Hi Nigel, I guess that it must be the same hole as the spring 20. using the lower hole will forse the spring 21 to slide against ...   06-18-2015 06:03 am

Brakes > rear brakes draging (10 replies - 4057 views)

Hi Nigel, Is this the same hole where I attach the left side of the spring 20?? BR Kim ...   06-18-2015 05:49 am

Brakes > rear brakes draging (10 replies - 4057 views)

Hi I am having problems with my rear brake binding. I suspect that the problem is related to the assembly of the hand brake system. On the attached ...   06-17-2015 08:01 pm

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hi Esprit, I measured the liners to be between 95,28- 95,32 pistons are measured to be between 95,10 - 95,13 as you can see the best clearance i ...   04-26-2015 05:56 pm

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

I have opened the engine, and unfortunately the piston to liner clearence is app 0,2 mm which according to the manual is to much. The liners ...   04-26-2015 05:50 am

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hi If I run the car at a constant speed of 50 MPH there is no smoke. Then If I floor it the car accelerates but ...   04-25-2015 02:45 pm

Engine & Transmission > Cam belt tensioner bolt stripped (4 replies - 2200 views)

sorry thread is "renovated engine burning oil" BR Barthol ...   04-19-2015 09:26 am

Engine & Transmission > Cam belt tensioner bolt stripped (4 replies - 2200 views)

Hi I had the same issue on my 79 engine. I changed to the semi automatic tensioner which uses two other holes. I guess that if ...   04-19-2015 09:25 am

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hi again, Just measured my valve stems and the "side to side " movement of the valve at 10 mm open ( using a dial ...   04-05-2015 09:15 am

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hi, I have taken off the head ( engine out )and looking into the cylinders there is a big clearence between the cylinder and the piston. With ...   03-28-2015 05:04 pm

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

hi all Thanks for all the help . Esprit, that was a lot of valuable information:-) I Decided to change the tightener, which turned out to be a ...   03-28-2015 06:42 am

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hi All You are right , I do not think I can repair the Stud with the Engine in the car. As I have both Treads for ...   03-23-2015 06:22 am

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

I have no idea on how the bottom end is built . It was done from the Guy in Uk from who I bought the ...   03-22-2015 11:15 am

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hi Tim, Just forgot, The car is NOT for Granny Driving. In my opinion also old motors is supposed to be used as intended. It will definitely see ...   03-22-2015 06:59 am

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hej Tim, Engine is supposed to be a 1979 907 standard engine with the standard liners( they are iron- magnetic) / pistons, Liners is honed ...   03-22-2015 06:55 am

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Found the error. I ran the engine for a little while closed the throttle and just rolled to a stop in 2 gear,then immediately removed the ...   03-21-2015 06:52 pm

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hi Joachim, Interesting reading. On my old Bikes I have used something in between. Running it through the gears, but gradually increasing RPMĀ“s being very carefull to not ...   03-20-2015 01:35 pm

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hi Gordon, I run it on Mineral oil 15/40. And the smoke is a lot, not in idle but during acceleration 2-3000 rpm . I have ...   03-20-2015 10:54 am

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hi Gordon, I run it on Mineral oil 15/40. And the smoke is a lot, not in idle but during acceleration 2-3000 rpm . I have ...   03-20-2015 10:54 am

Engine & Transmission > renovated engine burning oil (46 replies - 15104 views)

Hi Guys, After installing my 2,2 renovated engine i really understand why people says that stroking the engine is the single best thing to do to ...   03-20-2015 07:07 am

Engine & Transmission > Cam belt tensioner (2 replies - 1720 views)

Hi Gordon, Thanks a lot , I will leave the manuel tensioner on :-) Br Kim ...   03-14-2015 11:12 am

Engine & Transmission > Cam belt tensioner (2 replies - 1720 views)

Hi all, I have just finished installing my 2nd hand 2.2 907 engine.With the engine I also got a semi automatic cam belt tensioner. I now have ...   02-28-2015 08:17 am

Carburetors > air filter box (2 replies - 2042 views)

Hi Thanks a lot Now my breather just goes to the ground BR Kim ...   02-04-2015 07:09 pm

Carburetors > air filter box (2 replies - 2042 views)

Hi Can anyone tell me what I am supposed to connect to the huse connection on the lower rear side of my Dellorto airlifted box. Inside the ...   02-04-2015 06:27 pm

Carburetors > One more Jetting Question (4 replies - 3016 views)

Hi Tim you were spot on or almost Looking through the progression hole showed that barrel no 4 was half a hole ahead of the other ...   01-26-2015 04:00 pm

Carburetors > One more Jetting Question (4 replies - 3016 views)

Hi Jim and Tim, Thanks a lot. That is a lot of info and definitely something to work with. Using the parts I have i have changed ...   01-26-2015 05:54 am

Carburetors > One more Jetting Question (4 replies - 3016 views)

Hi Forum, I have just finished my 2.2 ltr engine and put it bask in the car. Specs Cams 104/107 Comp ratio 9,35:1 ( Meassured ) comp meassured to 150 ...   01-24-2015 09:57 am

Electrical & Instruments > smoke coming from Generator. (0 replies - 1374 views)

Hi, Aftar I have changed my engine I am experience problems with my Generator. As I just wanted to turn my new engine with the starter, I ...   01-02-2015 02:38 pm

Engine & Transmission > clutch release arm (0 replies - 1157 views)

Hi, I have changed my clutch and have now assembled the gearbox to the engine. My concern is with regard to the clutch release arm. Without the tension ...   12-13-2014 12:29 pm

Engine & Transmission > Crank Balancing (0 replies - 1287 views)

Hi All, Going to put in my 2,2 ltr engine i got to think about a few things The guy I bought the engine from did the ...   11-20-2014 07:03 pm

Engine & Transmission > Strange Noise (33 replies - 13676 views)

Hi Rick, This might be way off but it is an easy check. During the Summer I experienced a similar intermitent noise coming from my Engine compartment. I ...   11-19-2014 06:26 pm

Engine & Transmission > Changing the Engine (5 replies - 2542 views)

Hi Nigel, This was as suspected, thanks a lot for the confirmation. BR Kim ...   11-17-2014 07:02 pm

Engine & Transmission > Changing the Engine (5 replies - 2542 views)

Empty engine bay ready for cleaning ...   11-16-2014 11:42 am

Engine & Transmission > Changing the Engine (5 replies - 2542 views)

Engine coming out ...   11-16-2014 11:41 am

Engine & Transmission > Changing the Engine (5 replies - 2542 views)

2nd photo of old engine ...   11-16-2014 11:39 am

Engine & Transmission > Changing the Engine (5 replies - 2542 views)

Hi I am exchanging my 2.0 907 engine with a later 2,2 907 engine. My question is tabour the extra CW connection stud I have on ...   11-16-2014 11:38 am

Brakes > Vaccum Hose for servo unit. (1 reply - 2268 views)

Hi, I have had problems with my servo unit lately and it has turned out they my old vacuum hose was blocked, needs to be replaced. I ...   08-03-2014 03:35 pm

VIN Database for Jensen Healey & Jensen GT > VIN (3 replies - 3586 views)

Hi I am looking for the Vin number in my car, I have found the plates on the drivers door , on the dash board and ...   07-09-2014 02:41 pm

Electrical & Instruments > CW temperature sensor. (1 reply - 2040 views)

Hi I am mounting dellortoes on my jh, and I got the manifold with the "long cooling pipe" see attached photo. My problem is that there ...   06-19-2014 07:13 pm


 Current time is 03:22 pm
   1  2  Next Page Last Page


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems