I recently replaced my original fuse box with the new one from martinrobey.com part number 93065. I started getting intermittent lighting issues . ...   05-08-2023 05:08 pm

Thanks ,I'll try it. ...   04-28-2023 01:06 pm

By design does the door Courtesy light come on when either the driver side or passenger door is open, my light ...   04-27-2023 05:40 pm

Correction the fuse box I got from martinrobey.com is a 3 fuse and same as the original with slight changes. I plan cutting ...   12-16-2022 12:25 am

Redracer Thanks , also, would you know the i.d. of the bushing that you used. I believe its 5/8 " , but not sure. My thought ...   09-28-2022 11:13 am

Redracer How do you replace the steering bushing at the firewall? I can't see it from under the hood. ...   09-28-2022 01:04 am

After trying a tighter tolerance fit to pinion, it made no change in the play, but after a closer look found the movement ...   09-27-2022 07:47 pm

Redracer Thanks for the info, I'll make a shim if necessary. But one question , when I lift off the top plate is there anything ...   09-26-2022 05:38 pm

Thanks for all the responses, this will be my winter project. Last winter I did a new clutch, one piece driveshaft, Holley sniper efi And pertronix ...   09-25-2022 11:20 pm

Redracer, I have not done this before can you explain more. Do I add more shims or place them elsewhere? What is the lower plate for? What ...   09-25-2022 09:07 pm

sorry for the long delay , harborfreight.com sells a engine bar to support the engine from above using the fender flanging as support for ...   09-25-2022 01:41 pm

Has anyone adjusted the pinion gear preload. my steering has a slight play while driving. I checked out the steering shaft u joints they are ...   09-25-2022 01:31 pm

Has anyone replaced the current 3 fuse box with the new 4 fuse box part number 93065. looking how you did it. my current one ...   09-09-2022 07:09 pm

does anyone know the shaft sizes and number splines for the lower steering u joint, any local usa sources. ...   09-02-2022 07:19 pm

Took me 3 months complete this project. Requiring new fuel tank, fuel lines, fuel pump, throttle linkage and a custom fabricated intake manifold extension. I was well ...   07-17-2022 03:20 pm

Thanks for the info, I checked my camber it's within specs. I'll need to rotate my tires more , they're showing more wear on ...   11-20-2021 11:05 am

I am planning on refurbishing my front suspension, I believe my camber angle is too negative angle. Specs states toe in 0 ...   11-19-2021 01:10 pm

Thanks for all your advise, looks like an engine pull next. ...   11-16-2021 12:16 am

Ok. Rtv is not a good choice , however , it doesn't answer my question can you drop the oil pan enough to gain access ...   11-07-2021 11:07 pm

Has anyone tried to reseal the oil pan by unbolting and dropping pan straight down and resting in the front crossmenber. I looks like there ...   11-05-2021 10:25 pm

Can anyone tell me the size of the flywheel attaching bolts, I am looking a replacement part number I can buy a auto supply store ...   08-29-2021 09:17 pm

I would like to update new stock steering wheel. Can someone advise me on what size of splined adapter I need and who supplies them. ...   04-09-2021 12:12 pm

THANKS FOR THE ADVISE. it does sound like its a rear end issue. who did jensen have supply the diff, i read that they used ...   11-09-2020 08:10 pm

i may a stated it wrong , the pinion shaft does not move its the drive have assembly can slide back and forth along the yoke ...   11-09-2020 05:50 pm

today i did inspection on my 2 piece driveshaft. the shaft assembly is like new condition. the bearing is fine and the rubber boot the ...   11-09-2020 03:38 pm

today i did inspection on my 2 piece driveshaft. the shaft assembly is like new condition. the bearing is fine and the rubber boot the ...   11-09-2020 03:38 pm

does your jensen have a 4 or 5 speed trans. and is the driveshaft 1 piece. i have a 2 piece design for the 5 ...   11-07-2020 10:11 pm

my jensen has a 2 piece driveshaft with a center bearing. i noticed when under the car as i rotated the driveshaft in makes a jingling noise.Thought ...   11-07-2020 08:41 pm

I experienced today while driving the motor began to sputter ,loss of power and would not want to accelerate. It lasted for a short time ...   09-07-2020 03:39 pm

I never did an oil flush.How do you apply the oil flush (twice), also,several gunk products which one do you use. ...   09-01-2020 04:33 pm

has anyone tried different engine oil, the castrol 20w50 is sometimes hard to find, i get mine a walmart. how about mobil one ? what ...   09-01-2020 12:00 pm

Has anyone tried to convert to hydraulic clutch setup. My attempt with using an off shelf clutch master cylinder and slave , I could not ...   07-04-2020 12:40 pm

What is the correct oil level in stromberg carbs. I am looking for a reference dimension. Measuring from the top of the casting opening to the oil ...   01-10-2020 08:45 pm

my electric fan came with a 165 -185 thermostat, my heater hose line had old rusted out manual on/off valve which i removed to replace ...   09-23-2019 11:13 pm

i had the same issue, higher idle as it warms up, spring change appears to keep the idle more constant. regarding your radiator fan, i ...   09-22-2019 06:26 pm

FYI, we always hear about replacing the diaphragm , but i also replaced the spring air valve return. it made the idle smoother and for ...   09-12-2019 06:33 pm

FYI, if your rear view mirror needs replacement, i picked up one at mossmotors.com. Part number 801-085, $40. It comes with stem and plastic mount. ...   01-22-2019 12:17 am

I recently rebuilt a spare set of front calipers with new pistons and seals. I bench tested them before installing them. noticing when bench testing ...   11-30-2018 10:17 pm

Tom I have e3 3.46 model spark plugs, all plugs look good. using magnecor 8mm wire, they look good bought them 3 years ago... 3000 ...   11-15-2018 02:57 am

recently drove my JH. i notice engine ran a little rough while cruising in high gear. air temp was about 30 and engine was running ...   11-14-2018 08:54 pm