THE DRIVER SIDE SEAT BOTTOM HAS SPLIT. THE BACK REST IS FINE AS IS THE PASSENGER SEAT. ANY SUGGESTIONS FOR GETTING THIS FIXED IN THE ...   05-29-2020 05:51 pm

thanks for all the help. my orings should be here today or tomorrow. ill let you know how it goes. I have already removed the ...   05-15-2020 05:35 pm

Thanks for all the information. Luckily I noticed the leak before I got the car started. It was the front carb. I have ordered the ...   05-14-2020 01:59 pm

yes that is the one. a foto would be great ...   05-14-2020 12:31 am

I have tried tightening by hand the plug seem to turn in both directions without tightening I assume its the o ring seal or just ...   05-13-2020 09:54 pm

Clinton I think my water pump is leaking so Iam going to replace it. What is the best source for a rebuilt pump. Do you know ...   05-28-2016 01:34 pm

Thanks Brett Igot it all apart and kept track of the springs and small plastic parts. I could not see how moving the lever caused contact ...   03-17-2016 12:35 am

I have ordered bulbs from Delta. I pulled the non-working bulbs out. They were bad. I have most of the electrical working now. Cleaning the ...   03-15-2016 05:02 pm

Does anyone what to use for bulbs in the side marker lights. I have one front and one rear that don't work. The wiring diagram ...   03-11-2016 12:47 am

Thanks Clinton I thought I had run across that in the forum in the past. ...   03-06-2016 11:40 pm

I read on the forum that the amperage of Brit fuses and American are different. That seems strange. What should I use in the fuse ...   03-06-2016 01:07 pm

Thanks for all the help and recommendations ...   03-05-2016 11:35 pm

I adjusted the clutch cable. That helped a lot. As i paid more attention to what was happening i realized that at times it would ...   03-05-2016 11:34 pm

Lash How many miles were on your car when you added the kit?. I have 49000. It all feels really good now up in the ...   02-29-2016 02:38 pm

Thanks Brett Iput the car up on jack stands, adjusted the cable and ran the car. It now shifts fine up in the air. It actually ...   02-29-2016 01:27 pm

L I went for a drive. trans shifted well up through the gears but would not downshift. When I tried it would not go into gear ...   02-27-2016 07:49 pm

Are the side window seals available at the store difficult to install. Thanks ...   02-23-2016 01:09 pm

THANKS t4brew. I didn't think they were necessary but I have been wrong before. i'll just leave them out ...   02-15-2016 11:57 pm

DOES ANYONE KNOW THE SIZE AND THREADS FOR THE BOLT THAT HOLDS THE BRAKE DRUM ON. I REPLACED THE WHEEL CYLINDERS AND FOUND THE BOLTS ...   02-15-2016 02:25 pm

Thanks Art did you just rotate the alternator up after you removed the compressor and use the bolt and hole the compressor was in ...   01-07-2016 02:28 am

Does anyone have a picture of the alternator position on a non air conditioned JH? I have removed the compressor. It looks like the alternator ...   01-06-2016 11:07 pm

Thanks for the reply. I will probably just seal up all the openings and put it in a box. There was still a little pressure ...   01-02-2016 02:23 pm

I am going to remove the air conditioning compressor to allow better access. Is there anything additional I need to do to make sure it ...   12-30-2015 07:27 pm

Any specific plug recommendations for 75 JH. Thanks ...   12-24-2015 05:59 pm

i may try the cutting proceedure but i will mark everything up as Answerman detailed. thanks for all the suggestions ...   12-24-2015 02:35 pm

Thanks Gerald Ihave talked to a couple of guys at the British Car show a couple of years ago and they recommended the shop you noted. ...   12-24-2015 02:16 pm

Does anyone have a recommendation for a shop in the denver area that has JH experience. As i start to refurbish the car I am ...   12-23-2015 03:26 pm

What would you use to cut the belt. Its pretty tough stuff.\? ...   12-23-2015 03:22 pm

Thanks Answerman: I really appreciate the detail. My belt should arrive today so maybe I can attack the project over the weekend. ...   12-18-2015 07:56 pm

I am replacing the old belt as it is several years (10+) old. The car runs. Can i just remove the old one and ...   12-17-2015 09:51 pm

The new clip is thicker and therefore stiffer than the original. The grove is also wider. I can't get the clip started over the protrusion. ...   12-12-2015 12:37 am

So it pops over the top of the protrusion. it doesn't slide into the grove from the side. I guess you flatten the clip against ...   12-11-2015 05:12 pm

Does anyone have suggestions on installing the spring clip that hold the wheel cylinder in place. The old cylinder leaked and ruined the shoes. I ...   12-11-2015 12:50 pm

Thanks for the warnings. I changed the fuel T a long time ago but it has been awhile for the cam drive belt. I'll check ...   12-11-2015 01:27 am

Thanks Brett do you have any specific recommendations and rough cost ...   12-10-2015 02:11 pm

Thanks for all the information. I willprobably send them out to be rebuilt. I am going through the car as it has set for at ...   12-09-2015 10:40 pm

Where is the best place to have the crabs rebuilt. They have not been done since the car was new. It runs but after 40 ...   12-07-2015 06:14 pm

THANKS. I'll pick one up ...   12-04-2015 02:11 am

Thanks Frank I haven't looked but are there drain plugs on each ...   12-03-2015 09:50 pm

What oil is best for the diff and transmission. I don't believe either one has been changed since 1976. Any tips for draining and replacing ...   12-03-2015 01:50 am