Time to practice your skills with an x-acto knife & suitable gasket material! ...   03-05-2013 10:36 pm

You might also want to check out: www.putzkes-fahrspass.com for your Bilsteins. They were generous in their contribution to the silent auction event for the Jensen ...   01-28-2013 03:16 am

Thank you Brett & Pete for your input. Much appreciated.PK ...   01-10-2013 12:10 am

Does someone know the part numbers for the one piece 5-speed drive shaft universal joints? I think I remember someone saying they are easily available at the ...   01-08-2013 06:01 am

Thanks Kurt for the info. PK ...   06-22-2012 02:09 am

If my car had different cam(s) than what was originally installed in a 907, is there a way to tell? For instance is a 107 ...   06-21-2012 09:42 pm

I let the pad soak in MINERAL SPIRITS for several hours, and then kept washing in DAWN dishwashing detergent until all the funk was gone. ...   06-21-2012 09:30 pm

Just finished the change over from 4-speed to 5-speed, and getting ready to install the 5-speed speedometer cable into its housing on the Getrag unit ...   03-20-2012 02:07 pm

The release lever appears to be the same; the throwout bearing is different. I have not seen it yet - it is on order and ...   02-10-2012 04:23 am

Thanks Kurt-that is exactly the info I needed to modify the 4 speed pivot   ...   02-09-2012 07:32 pm

I am switching over from a 4 speed to a 5 speed tranny and would like to beg, borrow, buy, or barter a 5-speed clutch ...   02-09-2012 04:45 pm

Do the 4 speed and 5 speed transmissions both use the same throwout-bearing pivot? ...   01-25-2012 06:55 pm

The link for John Kimbrough excellant site is not working. Has something changed? Moved to a new site? If so, what is the new address?Thanks-PK ...   01-20-2012 02:57 am

I would like to thank all my friends and associates, who have shares time with Ellen and I at the Jensen East meets, for your ...   12-08-2011 05:26 pm

Thanks Brett. I'll give it a go without, so that I have a reference point. ...   08-03-2011 02:28 am

Is it necessary to hook up the choke cable to Dell 40,45s to start the car? Does it make it easier for cold starts? I ...   08-02-2011 02:01 am

For those intrested, here is a link to some photos of the Jensen East event in Lake Placid, NY :" THE ADIRONDAK EXPERIENCE" https://picasaweb.google.com/115853099307573999386/JHLakePlacidJune2011?authkey=Gv1sRgCKiVtvPDy8OoxQE# ...   06-26-2011 03:38 pm

Concerning the LAYCOCK TYPE-J OD: Is the drop in RPM, using the Laycock Type J OD unit less than, equal to, or greater than switching to ...   06-01-2011 01:05 am

I run .032 with good results. ...   08-08-2010 12:00 am

Photos of Jensen East 2010 in Kalamazoo, Michigan can be found at: http://picasaweb.google.com/115853099307573999386/JENSENEAST2010KALAMAZOOMICHIGAN?authkey=Gv1sRgCLnW_a22v6-Y8gE#   ...   07-20-2010 04:25 am

I've already busted two different set of snap ring pliers, trying to get the internal circlip off the rear-end of my 4-speed. I'm getting a ...   07-02-2009 01:39 am

Be VERY CAREFUL  when opening it up. The spring is under tension, and has a tendency to eject from its containment( mind did anyway). If ...   06-12-2009 11:18 pm

Have the details for the 2009 Jensen East extravaganza been firmed up yet? Thanks-PK ...   11-13-2008 12:16 pm

Thanks Mitch for playing "Jimmy Olson". What a fantastic job! We will be able to replay the fond memories of a super event and the ...   06-23-2008 01:48 am

Glendale,AZ to Malone, NY - about 3000 miles, fully loaded in boot & behind seats, 2 people, with hardtop, at "highway speeds" ,  standard engine ...   02-08-2008 05:13 am

Thanks for the quick reply Jim. PK ...   06-15-2007 06:50 pm

    I just replaced the Velcro on my convertible top finisher; the little tags that get stuck to the door jam. Noticed the front edge, ...   06-15-2007 04:51 am

Just mask off an area you feel is sufficient for attaching to the rest of the system, and  attach a note to the coating company ...   02-05-2007 10:13 pm

I bought Delta's header, had it coated (Swain) and install on the engine, that was raised up with a cherry picker, just enough to get ...   02-05-2007 02:59 am

You might want to check out the tech articles written by car electric guru, Mark Hamilton, at his web site:www.madelectric.com. A lot of good stuff ...   02-01-2007 03:40 am

Contact me off line re your front end. I'm in northern NY PK ...   01-11-2007 03:28 am

Thanks for the info. Unfortunately, it is at the same time as the Austin Healey International Conclave in Burlington, VT. ...   01-07-2007 03:37 am

Could someone supply the dates and whereabouts of the proposed Jensen East 2007 meet. If a web sites has been set up, the address would ...   01-06-2007 03:28 am

For an excellent read on alternators and things electrical, spend some time at:www.madelectrical.com. PK ...   12-15-2006 05:02 am

WOW! It really looks like you have got your guano together. I as well look foward to your replies. ...   12-13-2006 10:10 pm

White/ext;Tan/int. 1974 Vin#18849, engine#B7410 9816, door tag states date of mfg. as 01/11/74, odom reading of 93712 in reasonable good shape Vin#15893, engine#B7405 6219 bought to ...   12-05-2006 12:07 am

A friend of mine who owns several Brit. cars of various marques passed this onto to me, and I thought I would share with JH ...   11-13-2006 11:40 pm

Physical Therapy departments use different gradients of a strechy rubber elastic material, that is given to patients for exercise purposes. I had a piece of ...   10-08-2006 03:30 pm

Who amongst us knew what we were getting into, when we decided  to take the JENSEN HEALEY CHALLENGE? Speaking personally,it is a learn as you ...   09-17-2006 03:32 pm

Thanks Mark. I connected both seat bets and applied hand-brake, and it cranked over. However, when I looked through the box of old parts, that ...   09-11-2006 12:57 am