| ||||
|
Posts by redracer | |
---|---|
628 posts | Showing posts 601-628 of 628 |
Brakes > Brake Booster removal (12 replies - 20040 views) Assuming the rebuilt one is the same as the originals, yes, there is an adjustment: if you have in back on the car, 1st remove ... 05-04-2016 04:02 pm Ignition > oil in distributor 1975 Jensen (13 replies - 25375 views) There is the large outer O-ring on the end of the shaft, then a smaller one for the plug holding the oil pressure relief spring(punch ... 08-20-2015 04:47 pm Ignition > oil in distributor 1975 Jensen (13 replies - 25375 views) There is the large outer O-ring on the end of the shaft, then a smaller one for the plug holding the oil pressure relief spring(punch ... 08-20-2015 04:47 pm Ignition > Reinstalling the Lucas 25D distributor (4 replies - 12473 views) There is the large outer O-ring on the end of the shaft, then a smaller one for the plug holding the oil pressure relief spring(punch ... 08-20-2015 04:43 pm Intro Tech Board stuff > Jensen Healey Restoration in NY (4 replies - 10473 views) Michael: try contacting Jim Reilly at 631-938-3069. He lives in Coram and has incredible knowledge of J-Hs, both strret and racing ... 08-18-2015 02:15 am Fuel Stuff > rejuvenating fuel sending unit (7 replies - 21713 views) Gents: sorry for not responding sooner; John Tiesler ( JTiesler@woway.com) has done quite a bit of work with a very close replacement:
the Tr7/8, TBS5514 or ... 02-09-2015 09:43 pm Miscellaneous > My JH & Delta (25 replies - 71400 views) Nice going! Glad to hear the other two cars were in good company!! ... 02-09-2015 07:02 pm Miscellaneous > My JH & Delta (25 replies - 71400 views) John: just looked at your pix; I would STRONGLY recommend you put something over your driver's side floor mat as they are "Unobtainium"(as far as ... 02-09-2015 06:12 pm Miscellaneous > My JH & Delta (25 replies - 71400 views) John: Mike had his own shop in California for many years. He is a super mechanic and "go-getter" for anything J-H. You would have ... 02-09-2015 06:10 pm Projects > New Project 17505 (6 replies - 12919 views) I use whatever high grade is available; sorry, can't help you much with that but I don't think it will greatly affect the engine ... 02-04-2015 07:14 pm Engine & Transmission > Timing belt pully alignment (1 reply - 5462 views) Putting each of the bearings flush with the surface of the outer casing is fine(there will be a little space in the center) but don't ... 02-04-2015 06:18 pm Projects > New Project 17505 (6 replies - 12919 views) In addition to our "moderator's" recommendations, I woujld also add (4 speed only) Dow CVorning "M" Gear guard to the transmission and differential. 10% ... 02-04-2015 06:12 pm Carburetors > air filter box (2 replies - 7447 views) Goes to the breather tube for the crankcase, located on the top of the engine directly in front of the transmission. There should be ... 02-04-2015 06:07 pm Body & interior stuff > Door Hinge Screw Heads (6 replies - 5213 views) You can adjust the 3 door volts so there is some friction and then try to set the door. ... 06-07-2014 03:15 am Carburetors > starting after a lay off (13 replies - 20553 views) If you have SKYPE, most of these problems can be fixxed fairly easily(mine is rockclimber52). A vacuum gauge would be useful as well as ... 06-06-2014 08:29 pm Body & interior stuff > Door Hinge Screw Heads (6 replies - 5213 views) The adjustment for the doors is in the 3 bolts that go into the door itself. You will need to remove the door panel ... 06-06-2014 08:26 pm Body & interior stuff > Windshield (8 replies - 13904 views) The Jaguar's had a similar type windscreen, so maybe check for someone that does Jaguars.
As for the "caulking" no one uses the rubber strips anymore ... 06-04-2014 05:13 pm Projects > 16173 will be entering project status... (162 replies - 260610 views) answerman: there is a very nice fix for "the bend" in the hood caused by someone inadvertantly trying to close it without lifting up the ... 03-05-2014 12:03 am Engine & Transmission > OIL PRESSURE RELIEF VALVE (2 replies - 7111 views) Tes--I have done it many times:
Remove distributor; put old rag under opening to catch oil.
Use small pin punch to push split roll pin into the ... 03-01-2014 04:23 pm Engine & Transmission > Good oil seal - bad oil seal (9 replies - 18944 views) Glad to see you found the problem; for all our engine rebuilds we wrap teflon tape around the big cam wheel bolts, since, as you ... 02-28-2014 05:48 pm Engine & Transmission > Mark I cam belt tensioner need advice (17 replies - 24823 views) Unfortunately, you're correct about the earlier front crank housings. Either update that one to the later housing(don't forget the marks are 10 degrees off ... 02-28-2014 05:02 pm Brakes > Leaky brake valve (8 replies - 18168 views) Bob: you remove the 2 sliding shafts and the small ball that actuates the electrical switch. No predrilling is necessary as the 2 bore ... 10-21-2012 03:34 pm Brakes > Leaky brake valve (8 replies - 18168 views) Jay, Bob: what Sander has done will not compromise your brake system. The 2 end caps are removed and tapped with a 1/8" tap, ... 10-20-2012 03:22 pm Engine & Transmission > timing (4 replies - 8834 views) Don't know if you got the timing issue solved yet from Brett, but not I would be happy to help. Do you have a webcam? ... 10-20-2012 02:55 am Carburetors > Dellorto Filters? (7 replies - 23887 views) Wow--nice neat engine bay--well done! ... 09-14-2012 11:34 am Cooling > Heater Bypass Valve (Vacuum Activated) (12 replies - 28304 views) Just joined and rereading all the old mail: have plenty of the vacuum operated heater valves(still gold cadmium light plating). ... 09-12-2012 01:04 am Cooling > Radiator Drain Plug (2 replies - 9306 views) Just joined but assume you have it plugged": standard 3/8" by 16 threads/ inch. A decent hardware store will have this in brass. ... 09-11-2012 03:29 pm Cooling > Where are the vent hose outlets on the heater (6 replies - 16202 views) Jody: finally got logged into the JHPS web forum, something I should have done long ago; very impressed with your "HEATER BOX" videos--nice job. ... 09-10-2012 07:26 pm | |
Current time is 02:15 pm | ... 11 12 13 14 15 16 |