Home 
Home Search search Menu menu Not logged in - Login | Register
> Pat Connor

Profile Topics Posts
Posts by Pat Connor
21 postsShowing posts 1-21 of 21

Projects > LS engine swap (5 replies - 5193 views)

I have a '74 JH that I installed a SB 327 Chev. If the width of the LS is same or smaller it should ...   05-16-2014 04:56 pm

Body & interior stuff > Windshield (6 replies - 5357 views)

I have purchase a new windshield from Delta.  My concern is installation.  One local shop would not install it and a shop that specializes in ...   07-11-2007 04:11 pm

Wheels > 4 X 100 (2 replies - 5371 views)

Clif, if you want to go to 4 x 100mm on you wheels you can make 1" spacers with a dual bolt pattern. I made ...   07-03-2007 03:35 pm

Suspension > Rear Ends (20 replies - 15898 views)

I wonder why anyone who needs a new rearend and is not restricted by rules does not use the GMC 7.625" axel available in all S10 ...   05-31-2007 04:30 pm

Body & interior stuff > Body & interior stuff (6 replies - 6607 views)

!#$&%%$ I did the no no and broke my windshield. Does anyone out there know where to get a new one? ...   05-12-2007 11:24 pm

Engine & Transmission > New/replacement engine suggestions (12 replies - 7176 views)

I installed a 327 ci chev V8 in my Jensen. It is a lot of work and while it fits quite well the height of ...   05-07-2007 06:45 am

Carburetors > stuff under the gas tank (5 replies - 5304 views)

Hi Kevin: I used a rubber door mat from Home depot cut to fit. Low tech but it does not hold fuel or water thereby limiting ...   05-07-2007 06:35 am

Body & interior stuff > Seats (4 replies - 4456 views)

What was required to install the seats? ...   01-10-2007 01:53 am

Body & interior stuff > Seats (4 replies - 4456 views)

Has any one found satisfactory replacement seats for the Jensen_Healey.  Most seats seem to be too wide. My seat frames are worn out and the ...   01-09-2007 05:15 am

Suspension > Coil-Over Shock/Spring Conversions (22 replies - 18741 views)

Ron great info about custom springs from www.coilsprings.com .  What is their turnaround time on custom springs? ...   12-23-2006 04:32 pm

Engine & Transmission > Limited Slip Rear End (12 replies - 18755 views)

Judson Thanks for the corrections and info.  Good Luck with your Jensen. ...   11-28-2006 05:30 pm

Engine & Transmission > Limited Slip Rear End (12 replies - 18755 views)

With some work you can install a GM 10 Bolt rear end out of a '89-04' S10 GM pickup truck.  It is 54" wide at ...   11-27-2006 02:58 am

VIN Database for Jensen Healey & Jensen GT > Jensen Healey & Jensen GT VIN Database (274 replies - 212396 views)

JHC #19147 engine 327 ci Chev. V8 w/350 TurboHydro S10 GM axel w//3.08:1 ring and pinion. Originally constructed 04/12/74 Purchased 1983 from salvage (engine fire) Modifications began 2001; ...   11-25-2006 05:08 pm

Miscellaneous > Thinking about buying a JH (UK) (3 replies - 4857 views)

Miata seats have been used in the Jensen Healey and look really good. There should be many available. ...   08-14-2006 06:49 pm

Wheels > I'm going with 16's and I'm not sure what offset (8 replies - 10718 views)

I have also learned that their was a Torsen LSD available as an option for the 1998 Camaro and Firebird which uses the same axel. ...   08-14-2006 06:46 pm

Wheels > I'm going with 16's and I'm not sure what offset (8 replies - 10718 views)

For your information  a rear end out of a Chev S10 or GMC Sonoma width wheel flange to wheel flange is 54 inchs the same ...   08-14-2006 03:49 am

Wheels > Wheels (57 replies - 59392 views)

Here is a website for Diamond Racing Wheels. The have strong light weight wheels in various diameters with 4x4 bolt pattern available. If you want ...   05-25-2006 07:44 pm

Miscellaneous > e-Bay Spasm Recovery (6 replies - 5578 views)

One more Jensen, 65 sq. ft. less lawn to mow! ...   05-15-2006 10:36 pm

Miscellaneous > e-Bay Spasm Recovery (6 replies - 5578 views)

I sympathize I get that feeling everytime I see a Jensen-Healey advertised for 0 to $600.  I just know I could do something with it; ...   05-15-2006 04:13 pm

Miscellaneous > roll bar (2 replies - 3488 views)

All possible mounting spots are in sheet metal.  The proper way to mount the rollbar is with 1/8" plates on the underside to spread the ...   05-10-2006 04:00 pm

Suspension > Jack Points (2 replies - 6405 views)

Front: The strongest point is under the engine subframe.  The jack may also be placed under the structural member between the subframe mount where this member ...   03-19-2005 03:45 am


 Current time is 08:23 am
 


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems