Hi Tim. That has been my plan as well after lots of consideration, especially since Tim Engel has recently amplified that 2 107s are wimpy above ...   05-05-2008 07:29 pm

Speaking of time-honored repair applications...I think it was about 5 years ago when I cured the same problem with a carefully trimmed dose of duct ...   03-14-2008 06:53 pm

James, The oil gallery is the preferred location as the oil is pushed directly into the main oil gallery when the Accusump discharges. It's been a ...   02-11-2008 09:57 pm

A sad loss indeed. I always thought of Mark as Professor Helpful. He was always generous with his time and detailed explanations. It would be nice ...   07-24-2007 05:07 pm

Hi Jeremy. I have a W58 (that at least appears to be in very good condition) from an 82 Supra that's been sitting in my closet ...   07-23-2007 04:13 pm

You set a basic air pressure behind the piston in the Accusump at 20 or so psi. As long as the valve is open to ...   05-18-2007 03:15 pm

The Carter pump I have is P/N 152875. Can't find the paperwork, but that's what the label says. Scott ...   05-16-2007 03:42 am

They don't get mentioned on here often, but I have five + years of trouble free road and track usage on (and can recommend) a ...   05-10-2007 09:50 pm

Hi Jeremy. Glad to hear your driving it! Meant to let you know the tool arrived fine. Hope it helped and no leaks. Been there with the ...   05-09-2007 04:43 pm

I have a 2.2L also. Idle jet is either a 50F9 or a 55F9--it's been a few years since I did the jetting and I ...   04-09-2007 04:45 pm

I'll jump in as I have run Weber 45s for 10+ years. Like Pete, I eventually found that a rich enough "idle" jet was what ...   04-06-2007 05:21 pm

When I did it 10 years or so back I used a battery relocation kit sold by Summit that had everything needed, from the cable ...   02-01-2007 02:30 pm

VIN 16709 74 4-speed Bright Yellow Second owner since 1979. Took it apart to replace rusty rockers (rusty everything really) in 1985. Had kids. Back on road ...   12-22-2006 04:21 pm

I stand corrected and apologize for the misdirection. Teach me for listening to an "expert" instead of researching myself. Glad you did. S- ...   12-15-2006 12:27 pm

I believe the A or B stamps on the Mahle pistons relate to weight, not size. If you get the whole shebang balanced I don't ...   12-14-2006 05:34 pm

Jeremy, Installing the rear main seal is tricky, and the time cost of getting it wrong is high. I have a special seal installation tool I'm ...   11-28-2006 07:19 pm

Hi Frank. Since no one else has replied... The 4-spd and 5-spd rear ends are slightly different. The 5-spd rear end has a slightly higher (lower numerically) ...   06-25-2006 07:36 pm

Well, that was special. I just spent the better part of an hour writing a long account of the event and lost it all when the ...   06-13-2006 08:07 pm

I carry a spare clutch cable. I've had at least two snap over the years, and it's not something you can buy at the local ...   03-02-2006 01:41 pm

So what is your overall impression? Looks like an exact replica. Does it feel substantially lighter? Obviously you haven't leak tested it, but are you well pleased? Scott ...   10-19-2005 01:50 am

Me too, although I'm skeptical about the $100. Konig is a long established and respected mid-range brand. As I understand it, Panasports through Delta are an ...   08-02-2005 03:25 pm

Dan, So how does it drive? Ratios good? Nice RPM drop at higway speeds versus the 4-speed? That's the primary benefit I'm looking for. I have a ...   07-27-2005 07:51 pm

Yes.  205/60s work fine/look good on stock wheels.  An inch wider wheel would no doubt  be better, but I haven't found any thing as light as the ...   06-24-2005 02:02 am

It has been more than 10 years since I put them in, so I don't recall the exact measurement, but it seems to me that ...   06-18-2005 02:17 pm

Jim, FYI some seat rails are currently on Ebay. I have no connection. Scott ...   06-09-2005 08:05 pm

Delta hasn't had patch panels for seemingly decades and I've never seen another source surface. I would be interested, cost dependent (although I have just one JH). 4, eh? ...   06-01-2005 08:14 pm

I can tell you that a high compression 2.2 is a wonderful addition to a JH from a driving/performance standpoint. Probably a couple of years ...   06-01-2005 08:03 pm

I have seen many references over the years to the looonnnggg pedal throw, but I don't recall any mention of the 4-speed clutch action being ...   04-14-2005 07:39 pm

Drove the 567 miles from the northern suburbs of Chicago to Kansas City yesterday in my JH and averaged better than 70 mph (including gas, ...   04-04-2005 10:21 pm

A company named Fidanza used to make aluminum flywheels for Lotus Espirits that would be suitable for our cars, but I don't think they have ...   04-01-2005 12:35 am