Gary, take the arm rest off, 2 screws, window crank, 1 screw, any stainless trim you might or might not have, and then from the ...   11-29-2010 06:04 pm

Is the new battery fully charged, it could have been sitting on the shelf for a while, try giving the battery a jump start, does ...   11-21-2010 02:20 pm

Well if you have a new battery and it is fully charged, does the engine now turn over faster. I dont think you have a ...   11-16-2010 07:20 pm

I'd like to see that picture when you get it Greg. Brett ...   11-09-2010 07:02 pm

http://www.macgregorukcarparts.com/index.html These guy's are pretty good as well ...   11-05-2010 01:04 pm

At the East Coast Nationals this year we had a tech session on oil's and ZDDP came up as thee most important item to have ...   11-04-2010 01:46 pm

As a note, the new Lucas flasher units in my own experience are basically crap, they are a mass produced cheap product. I ended up ...   11-03-2010 03:47 pm

Do the turn signals work ???, the hazard switch when turned on bypass's the turn signals and they should flash even if the key is ...   11-03-2010 01:08 pm

http://www.jensenhealey.com/images/JHboard_logo.jpg ...   10-30-2010 06:56 pm

Well here's to another 20 great years then. Brett ...   10-28-2010 04:41 pm

Thanks for the smile ................... I'm not alone (car companions: tow rope, cell phone, small toolbox and oh yea, fire extinguisher) ...   10-24-2010 02:43 pm

Well I have been reading along on your trials and tribulations, looking at the pictures and will chip in with my two cents. First the thing ...   10-24-2010 02:35 pm

I use a flame thrower coil with the Allison and have had no issue so far, of course with that said ...   10-20-2010 12:56 pm

Terry, its all a matter of emisions and choke style, the newer 175's have more and more ports and bypasses verse's the older ones. If ...   10-19-2010 01:26 pm

I'm a NGK man myself ...   10-19-2010 01:06 pm

clean it and free up the nut while out, check the bearing to, put it back in with a dab of lock-tite. Brett ...   10-18-2010 06:13 pm

Get them off Delta they give you a detailed instruction guide and I believe they are Addco,  one tip. have the front wheels on a ramp ...   10-16-2010 08:01 pm

there's a picture of the SU fuel pump right on the opening page of the club store link. click on that for the details. Brett ...   10-16-2010 07:53 pm

no points with the allison, it has a optic and special rotor along with the dizzy rotor on top, it's an older unit and maybe ...   10-10-2010 02:07 pm

John, if you have the parts from the switch it is very simple to put it back toghether, there were two styles of switch's early ...   09-28-2010 01:00 pm

First off forget the mark on the dizzy pulley, they are interchangable with the cams. Set the crank at TDC with the cams aligned, check ...   09-04-2010 01:23 pm

That's correct, they need to be "seated", also if you clean up the hub you will notice a cut out in the seat that makes ...   09-02-2010 12:46 pm

what did the tester say was the common issue for seeing pulsating readings, sounds like a warped rotor to me. Brett ...   08-30-2010 12:53 pm

yes it is, but I dont recall if it is the early 2 bearings together, or the later larger single one. A price check would ...   08-30-2010 12:46 pm

Timkin outer cup, LM11710  / cone LM11749 Inner cup L44610  /  Cone L44649 Tensioner Bearing SKF 414871A (just happened to be on the same sheet of paper) Brett ...   08-29-2010 01:58 pm

Jim, there are two screws one in each corner of the upper  dash pod, then the pod is resting on a shaft, depending on if ...   08-27-2010 12:51 pm

Depends which one you have, late model  bearing nothing special, early ones use a oddball wrench to adjust. Brett ...   08-20-2010 06:41 pm

Mitch, even if it is not the tensioner bearing thats your issue, it sounds like you may just want to change it anyhow if you ...   08-20-2010 01:06 pm

Frank, I brought some poster size wiring diagrams for JH's and Interceptors to the Nationals the last few years as a auction item, not all ...   07-07-2010 12:49 pm

On an original rocker panel there are nuts welded into the panel so that the fendor bolts down to it, if you have the Delta ...   06-27-2010 02:14 pm

I have a copy of an old post from back in 04 that list's a Monroe Senseatrack for the front. P/N#5752 ST price listed was ...   06-22-2010 01:25 pm

Colin, seeing you mention needles I assume you have Strombergs, if it was me the first thing I would do is look at the color ...   06-12-2010 01:49 pm

if your timing is on then I would look at the carbs, sounds like it's lean at high rpm's. Brett ...   06-10-2010 12:58 pm

Vernon, there is no real spacer in that sense but there is a split wedge shaped washer that sit's just after the splines, it is ...   06-08-2010 12:52 pm

If you no longer have the tube I would suggest to get a used one, then use a marine metal epoxy to keep it in ...   06-07-2010 12:53 pm

Sounds like the throw out fork is not in the pivot ball ???  Clutch pressure plate and bearing is the same for GT's and JH's four or five ...   06-03-2010 01:47 pm

John, auto speed shops have a fake SS covering that can slip over regular gas hose and comes with a nut like cover that goes ...   06-03-2010 01:38 pm

FYI Brett. 2010  Events Schedule 2010 Jensen East Nationals Great Lakes Schedule of Events   Wednesday July 14th Arrival and Registration on the Mezzanine Group Dinner at Old Burdicks Bar & Grill (In the Hotel) Hospitality ...   06-02-2010 01:42 pm

When I bought my JH back in 87 I was offered a AH at the same time for 5K more than I paid for the ...   05-27-2010 01:53 pm

I would love to comment on this discussion Art but your "wordage" just smack's of confrontation. But if you would post some picture's of your ...   05-25-2010 01:24 pm