Bump   ...   05-16-2013 01:24 pm

To check if the rings are shot you need to do a compression check, make sure though that the carbs are fully open otherwise you ...   05-16-2013 01:22 pm

Times running out to pre-register for this show, already have a bunch of JH's and Interceptors commited. This is a fun filled event with lots of ...   05-14-2013 01:25 pm

I have fixed up a couple of GT power window problems in the past with out replacing any parts, 1st by taking the switch's apart and ...   05-09-2013 01:01 pm

The oil seal is a standard seal CR (Chigago Rawhide) #14857. Brett ...   04-19-2013 01:30 pm

Joachim, the vanagon does use a 5/8" manual shutoff valve that works very nice on a JH, I put one on a friends JH last ...   04-18-2013 01:29 pm

Art, funny you should ask this question just now, I have two heater boxes apart on the bench, one with the vavle and one without. ...   04-16-2013 01:04 pm

Registration form on Web site, also on Face book. ...   02-28-2013 10:52 pm

Getting closer   ...   01-26-2013 01:35 pm

A 1974 red paint code mixed to that probably wont match very well to the car now, you might want to go to a body shop ...   01-22-2013 12:51 pm

Paul, sorry I dont have the P/N# but they are a pretty standard U-Joint, if you were to take it to a shop I'm sure ...   01-09-2013 12:52 pm

BUMP. Bumpty ...   12-20-2012 01:46 pm

Roland, there are copies of the "Standard" in the members area but only for 2000, 2001, 2002. though there is 2003 to 2005 listed there is ...   12-20-2012 01:43 pm

...   11-26-2012 12:56 pm

My notes say it is a SKF 414871A, that is the one piece fat one not the two sandwiched together #. I might have that ...   11-26-2012 12:56 pm

Frank if it does fit please share the info, I for one have not heard of this before. Thanks Brett. ...   11-15-2012 12:51 pm

Just to add to this, Pete is a great guy and you should not hesitate to take advantage of this opertunity should you need it, ...   11-01-2012 01:20 pm

For your Info. SAVE THE DATE Jensen East Annual Meet May 29 thru June 2, 2013 Shepherdstown, WV Open to all Jensen enthusiasts, current and future owners, family and friends! More ...   10-12-2012 02:20 pm

Well hopefully when you align things the cam marks will line up and you dont need to touch them, but if you have to it requires loosening ...   10-12-2012 01:51 pm

Ok here's a quicky of what to set your engine up to. set the crank to TDC aligning the marks up. (make sure #1 piston is ...   10-11-2012 01:34 pm

You would look directly on the face of the cam gears themselves, there are usaully two to three small hash marks about 4 sprocket teeth ...   10-11-2012 01:24 pm

David, I dont have any good pictures of what I did but I tried a bit of RTV and didn't have much luck with that, ...   09-29-2012 01:10 pm

Yep there are supposed to be two horns, one high and one low. ...   08-15-2012 01:05 pm

he's on Face Book if you need him.   ...   06-24-2012 01:47 pm

Paul, I'l give that a try nothing to lose but I will use a mask and gloves, not sure if you have looked in the ...   06-22-2012 01:01 pm

Art, thanks for the reply, last time I tried to clean up the pad as well but it was filthy and just kept oozing ugly colors ...   06-21-2012 12:55 pm

Well I have got around to going over the rear differential of the car I'm restoring, thought I would change the oil in it check ...   06-18-2012 07:55 pm

Their are probablby a ton of opinions on this subject but mine for what it's worth is, not to tight not to loose. That said ...   06-18-2012 07:42 pm

My thoughts on this issue, assuming the piping and seal etc are all correct there is a vent hose that goes thru the trunk floor ...   06-15-2012 12:53 pm

Another spot to have a look at besides what Jim mentions would be the bushing at the end of the column going thru the fire ...   06-12-2012 12:47 am

get your tester out and see which wires have power, the black wire should be ground, probably because the blinker is bolted to the bumper ...   06-09-2012 01:21 pm

Oil and filter changed, car washed, carpets cleaned drove around for the last couple of days and all seem's well (Knock wood). So now just waiting ...   05-23-2012 12:50 pm

Jodie, dont you mean getting up early ??? Brett ...   05-17-2012 01:03 pm

Best way to find out what it's for is to follow the wires to what they are hooked up to, my money is on the ...   05-17-2012 01:00 pm

Bump Bump ...   05-15-2012 12:35 pm

Jodie, if your a due's paying member of JHPS you get a great monthly magazine called "The Standard" with color pictures of a featured car ...   05-08-2012 01:12 pm

Mitch did you see the the club magazine "The Standard" this month an article say's you dont need to mod anything except a rail. Brett ...   05-07-2012 01:19 pm

try turning the dizzy untill the engine starts to sound good and you get proper throttle responce, then see what the light tell's you. It's ...   05-07-2012 01:15 pm

Chris, sorry I cant give you a pointer on how to install the seal but I can recommend on how to get the best life ...   05-07-2012 01:10 pm

turn the crank shaft by hand till you line up with TDC, make sure the cams align and the #! piston is at the top. ...   05-06-2012 02:09 pm