bump https://www.facebook.com/brett.gibson.3344#!/photo.php?fbid=826420630705807&set=gm.721420184577089&type=1&theater ...   04-03-2014 12:46 pm

I run the Crane XR700 with no mod's to the tach and it works ??? ...   03-27-2014 12:59 pm

Going by past events and what is listed on the site the Awards banquet would probably be Saturday Night, car show Saturday during the afternoon, ...   03-21-2014 01:23 pm

Frank, click on the link in  Steve's post and it will take you over to the Jensen site, then click the link there to WI. Brett ...   03-20-2014 01:10 pm

Yes I used it, painted it on with a brush placed plastic wrap over the top and let it sit for 5 to 10 minutes ...   03-15-2014 03:31 pm

Whever the rotor arm is pointing to on the cap when the engine is setup on the timing marks, that is the number one cylinder ...   02-10-2014 12:56 pm

That would be were the dizzy rotor is pointing to inside the cap when the #1 piston is at TDC the crank timing mark is ...   02-09-2014 01:57 pm

Please post a picture of the header when you get it, would be nice to see what it looks like. As for putting the normal ...   02-01-2014 01:26 pm

Dont believe I have seen a JH two piece, Lotus might use one but not sure it would clear the steering shaft on a JH. ...   01-29-2014 06:41 pm

And that is good advise. ...   01-22-2014 07:27 pm

On my engine at least the stud was not a press fit but threaded ??? later style engine, went to adjust it once and the ...   01-22-2014 01:01 pm

My 2 cents would be change the bearing, a $5 bearing is not worth losing the engine over and you are questioning the setup so ...   01-21-2014 01:58 pm

Hello Claus, it's very important that you do not seat that rear main seal flush, go with the measurement you got and you should be ...   01-20-2014 02:13 pm

Roland what you need is a piece of spring steel and bend it into shap, or another method would be to use a cabinet magnet, personally ...   01-17-2014 01:50 pm

I agree using lead does have it's issues but there are lead free products that do the same thing. http://www.eastwood.com/ew-standard-lead-free-body-solder-kit-with-dvd.html no connection just to show an example. But ...   01-16-2014 01:28 pm

JC Whitney sell a leading kit with the proper tools to do the job, not cheap, from what I have picked up about leading it's ...   01-15-2014 01:24 pm

BUMP ...   01-06-2014 01:25 pm

The work Viva shop manual I have does not cover the 1800 just the 1159cc to 1256cc, 1970 to 1977, but it does show the same ...   01-01-2014 07:07 pm

My 2 cents, get rid of it, remove the light blue tubing and plug it off at the source, run the green line just to ...   12-31-2013 01:30 pm

If you have a 5-speed then the shifter assembly probably needs to be rebuilt they are prone to wear the plastic bushings out, then they ...   12-31-2013 01:19 pm

Tom makes a good point all the bolt holes should have no oil in them, what cant be sqeezed out ends up being compressed, that ...   12-28-2013 01:33 pm

Plus it only needs to be snug not tight.....   ...   12-24-2013 01:19 pm

Here is a suggestion, (it's the way my car and afew others are) put a full face gasket over the by-pass valves on each carb. ...   12-24-2013 01:17 pm

If the ignition system is fine (big assumption) then it sounds like you have an air/vac leak. ...   12-23-2013 01:10 pm

I installed a couple of these repair panels and ended up having to modify them to get them to fit correctly, if I had to ...   12-21-2013 03:53 pm

Well lets see if it was my car and they were too rusty to use I would, get the car up in the air securly, ...   12-07-2013 05:50 pm

Roland, I was in the post office for some stamps yesterday and did notice that $64 price to ship, but they also have a slower ...   11-23-2013 01:35 pm

3M make a foam tape (differant sizes) with sticky on one side that blocks off paint getting into jams and such around doors hood and ...   11-23-2013 01:28 pm

Just remember the front fenders need to be on before you can rehang the doors, does'nt work if the doors are on first, ask me ...   11-22-2013 01:03 pm

Roland Have to agree that kind of postage is rediculas, have you gone to the Delta Motor's site they are using the parts book there. ...   11-22-2013 12:58 pm

https://sites.google.com/site/johnsjensenhealeywebpage/ ...   11-22-2013 12:50 pm

The Club sell's them. $34.00 http://www.jhps.com/mm5/merchant.mvc?Screen=PROD&Store_Code=jhps&Product_Code=PCS&Category_Code=LIT Which helps the Club. ...   11-21-2013 02:15 pm

I left the outside of the fender in primer and only painted color on the inside and "jams". so that when everything is back in ...   11-21-2013 02:09 pm

Just recieved a message from John Kimbrough sharing the link to his new Web-Site, for those of you who never saw John's old site you ...   11-21-2013 02:00 pm

Have to go with Art on this, I painted mine inside as well as the jams so they would match when I paint the car ...   11-20-2013 01:20 pm

Art, I would go to Mcmaster-Carr and buy a piece of gasket material that is gasoline compatable and just cut your own using the old ...   11-19-2013 07:18 pm

Pry it out gently or you may crack the rubber around it, use a bit of silicone to help it along.   ...   11-13-2013 01:02 pm

You might want to give British Masters a call they have a bunch of used JH stuff and not all of it is listed on ...   10-31-2013 01:12 pm

Frank, I will send Judson a Facebook message that you are trying to contact him, I'm not one of his FB friends but I think ...   10-26-2013 01:17 pm

I have removed most of the vacuum lines and plugged them off leaving only the inlet manifold to the brake booster, plus I blank off ...   10-19-2013 01:26 pm