If the "upper hose" you are referring to is the one to the radiator, the water should NOT flow through it until the 165 or ...   07-19-2017 01:10 am

The fuel pump itself is not fused; the "inner" or "HOT" side of the fuse box(closest to the center of the car) has a link ...   07-17-2017 02:14 pm

Has anyone used this product? It sounds good as it has a very high boiling point and is non corrosive to engines(especially nice for our ...   07-06-2017 05:34 pm

Didn't know Delta sold any except for complete assemblies: The ones that B.P. Northwest sells ARE tapered with one side(the top/upper side) a little wider than ...   06-27-2017 02:57 pm

Some of you may already know this, but there is now "FRESH" rubber for our cracked/deteriorated side light markers(also the same for Interceptors). I received a ...   06-26-2017 06:16 pm

Frank & all: the tabs for a sway bar should be pointed back. You have to drill a hole in the supporting ...   06-26-2017 06:04 pm

It is NOT in the "T" itself but in the fuel line that runs back to the top of the tank where the 2 other ...   06-25-2017 05:12 pm

Have a N.O.S. one; will try to get measurements soon. bruce madden ...   06-23-2017 02:00 am

Fuel line to "T" is 5/16"; the plastic/black nylon lines have reducer rubber(1/8" I think) going to the charcoal cannister in front. (be ...   06-21-2017 01:48 pm

Stu: 1) the tabs on the locking ring are just for getting it on and off(screwdriver works well) 2) Jim pointed out the very important anti-siphon valve(about ...   06-20-2017 11:44 pm

if it hasn't been done yet, I would strongly advise getting the tank internally sealed, such as POR15. Mastercoat, or KBS(haven't used their products yet). Just ...   06-16-2017 07:19 pm

Thanks, Nigel; will check it out. ...   06-16-2017 02:05 pm

Nigel: I would be very interested if you knew or could find out what LED bulbs work for the instrument panel. I've done the rear ...   06-15-2017 09:17 pm

wow--the outside looks beautiful! Love the way you put the white "speed" hash marks on the bottom--gives a good impression of moving fast. bruce madden ...   06-15-2017 08:34 pm

1) most likely part of exhaust hitting floor pan or transmission bracket 2)later covers are 2 piece, with many just leaving only the top one on ...   06-15-2017 05:19 pm

we have found the velcro to not be sufficient to hold the side of the top on when the windows are down, not to mention ...   06-15-2017 05:10 pm

yes; I can help(as I'm sure many others can as well). Please try to explain where/what/how the "rebuild" is going. bruce madden ...   06-14-2017 12:32 am

If you pull the top off you will notice the 2 holes in the bottom of the piston; if they are closest to the butterfly, ...   05-28-2017 12:58 am

Looks nice; just wondering why the carb. tops are 90 degrees from where they would normally be? ...   05-27-2017 11:40 pm

Stu: please contact me through the email I provided earlier. Again: RedRacerbm@gmail.com ...   05-15-2017 01:58 pm

Stu: finally got around to checking my stuff, and have 2 of the polarized plug(have never had a request for this part) that attaches to ...   05-14-2017 04:27 pm

Mike D'Olimpio at DELTA got some better engine mounts in that will likely fix your "height" adjustment. The former ones that were sold had ...   05-11-2017 09:42 pm

Stuart: I'm pretty sure I have one off one of the many cars I've had to cut up. RedRacerbm@gmail.com Also, try Hank Leach, who bought ...   04-26-2017 03:30 pm

Have about 15, but none in "perfect" condition(cost for that one would be over $1000) If you still have yours and the main problem is "the ...   04-10-2017 05:14 pm

Randall: years ago(late '90s) we had to install quite a few on our cars(Atlanta, GA.). We found someone who had done Jaguars which have a ...   04-05-2017 09:58 pm

Pretty sure I have good "underpads" for both sides, but obviously more for the "right" side since we're left hand drive in the U.S. ...   03-18-2017 03:08 pm

http://www.deltamotorsports.com/cgi-bin/bigimage.pl?site+DMSCAT+img+/products/Images/LockheedRearBrakesPlate.gif Don't know if this helps, but go to Delta Motorsports, click on brakes, Lokheed, and there will be the pic from the original book. If you ...   03-08-2017 08:47 pm

Sure, I can help; original owner and I work on them all the time. I have used SKYPE for instant help for some(will send you ...   02-21-2017 08:42 pm

Assume you mean one of the half shafts in the rear? Yes, I have plenty of very good used ones, but I am on the ...   02-18-2017 05:25 pm

Glad to see you got it chugging along again. As for the exhaust, the suspension was never a "hang" it set- up where going ...   02-07-2017 02:02 am

Actually, the press on dust disc was of later design; we remove them and replace with a standard seal as most of the early brakes ...   02-05-2017 04:43 pm

Unfortunately, you will assuredly have to remove the tm(unless you can make a VERY specialized tool). R&R for a 5spd. is 6 hours,(5 hours for ...   12-15-2016 12:05 am

I assume you mean the fulcrum half-moon point inside the bell housing? Back in 1992 mine broke as well, but probably from the fast, hard, shifting ...   12-14-2016 10:33 pm

Yes, heat in the left side(driver's side for us in the USA) of the cockpit can be annoying. There was a piece of foam about ...   11-22-2016 01:59 pm

Before I would do anything myself,I would first DEFINITELY call the radiator shop to see if they could redo the work, and if they don't, ...   11-17-2016 12:37 pm

POR15, KBS, Mastercoat ( http://www.masterseriescoatings.com/index/products/primer/ ) will work just fine even on heavily pitted and "holey" tanks. They are easy to use so you can do ...   11-16-2016 02:31 pm

Although I'm in Atlanta, too far for your desires to drive/trailer, if you have SKYPE and some mechanical expertise(usually they are the best for J-H ...   11-16-2016 01:59 am

If you lay the harness on a large floor, most of the design will be obvious. The later harnesses (J-H #97764; first were #90587, then ...   11-10-2016 03:38 pm

Frank: I usually retrofitted the older style tensioners(concave outer surface as opposed to the flat integrated later style) since changing the 2 bearings was easier, ...   11-06-2016 02:27 pm

On all the rebuilt water pumps I have done, I include an allen bolt to replace that one troublesome hex bolt, making removal and ...   11-03-2016 05:56 pm