| ||||
|
Posts by redracer | |
---|---|
628 posts | Showing posts 401-440 of 628 |
Engine & Transmission > Oil Pressure (27 replies - 26366 views) Sounds like the cars idles okay, but upon driving you are using the differential and transmission. I would check the fluid and fluid level in ... 07-31-2019 01:13 am Engine & Transmission > Oil Pressure (27 replies - 26366 views) I assume when you replaced the thermostat, it was a 2 stage one as required?(if single stage the water will keep running through the ... 07-26-2019 01:42 pm Engine & Transmission > Oil Pressure (27 replies - 26366 views) Sorry to hear; it's certainly not the new radiator.
You said you smelled oil burning; first determine where it's coming from and then one can ... 07-16-2019 12:55 am Brakes > Need some brake wisdom (9 replies - 10480 views) cjw: here's a post I did a few years ago(use the "SEARCH" box at top). Read some of the other comments as well
Hope this helps:
Brakes ... 07-14-2019 10:56 pm Engine & Transmission > Oil Pressure (27 replies - 26366 views) You're okay for now, but usually at idle(after the engine has warmed up) the pressure would ideally be 20-25psi. Lower than this indicates slightly worn ... 07-11-2019 02:09 pm Engine & Transmission > Static Timing adjustment (12 replies - 13997 views) thanks for doing the "writing" Tim; I don't type as fast as you and would have answered in a day if you didn't.
Once again users, ... 07-05-2019 06:16 pm Body & interior stuff > Steering wheel question (9 replies - 19429 views) I've used LEXOL on the steering wheel and that keeps the rubber from deteriorating.
I also recommend Meguiars #40 on your dash, etc. Use a foam ... 07-02-2019 03:22 pm Engine & Transmission > Rear mount Turbo (6 replies - 7835 views) Just saw this thread; in Atlanta, in 1978, there was a couple of guys named Tom Wyat and Tom Gage(they used to work for Bob ... 07-02-2019 03:04 pm Engine & Transmission > Oil Pressure (27 replies - 26366 views) The oil pressure is directly affected by the water temperature. The CHAMPION 3 row aluminum will take care of that and is much cheaper than ... 06-28-2019 12:29 am Brakes > Brake refurb (8 replies - 9715 views) Sounds good(glad to see your friend will patch weld it and not "bondo" it), but if I am not mistaken, epoxy primer doesn't flex much ... 06-27-2019 04:15 pm Brakes > Brake refurb (8 replies - 9715 views) Tom: whikle you're doing all this mechanical repair the MAIN problem is keeping the "tin worm" from doing a number on the panels.
POR15, KBS, Mastercoat, ... 06-27-2019 02:08 pm Suspension > Upper Ball Joint - Rivets? (5 replies - 11369 views) Don: after you drill out/grind pout the rivets. you may wish to make the upper ball joint aid in your camber, which is not adjustable ... 06-24-2019 12:02 am Engine & Transmission > Need to change out the Timing Belt Tensioner (23 replies - 36257 views) I suppose I should have responded earlier, but since I read you had ordered a pair for the earlier style tensioner, I did not reply.
I, ... 06-06-2019 10:24 pm Projects > 19661 paint and bodywork (64 replies - 65826 views) Something you may want to check if you're installing the "extra thick" padding, especially on the firewall and floors.
Having just finished working on a '75 ... 06-06-2019 09:36 pm Miscellaneous > Wheeler Dealers (6 replies - 8771 views) All the post '73 vehicles have the black area where the headlight is. The west coast vehicles all had the "J" badge like the precious ... 05-29-2019 05:16 pm Ignition > Crazy no start issue for 73 JH # 12265 (3 replies - 5483 views) Hey gang: this is "double listed" and was solved 2 days ago:
cjwilson
Member
Joined: 04-23-2006
Location:
Posts: 7
Status:
Offline
Hey Brett,
Thanks for answering. Yes fuel ... 05-22-2019 11:29 pm Engine & Transmission > Main Bearing Clearance (12 replies - 28412 views) Already printed out the 12 pages from your link; will do the same for the remaining items.
One peculiar note I'm sure many notice in the ... 05-21-2019 04:26 pm Engine & Transmission > Main Bearing Clearance (12 replies - 28412 views) Thanks once again Tim; I'll print these "updates" & put them in my shop manual.
Keep rolling!, bruce ... 05-21-2019 01:29 pm Engine & Transmission > Main Bearing Clearance (12 replies - 28412 views) assume you used a plastigage for these measurements and all nuts were torqued down to specs? If so, you're in the standard 907 range for ... 05-20-2019 01:39 am Accessories > Factory Removeable Hard Top parts? (6 replies - 14300 views) try these rubber company; I have catalogs from them from 25 years ago, but they still seem to be in business. J.C. Whitney used to ... 05-17-2019 01:09 am Fuel Stuff > gas tank install (2 replies - 5189 views) If you have one of the pre '75 filler tubes then opening the cap and use your finger or equivalent to get that fianl section ... 05-16-2019 04:34 pm Brakes > Lockheed or Girling? (4 replies - 6850 views) Interesting choice:
For regular street use, one would prefer the Lockheed since they are self adjusting, unlike the Girling; however, for road racing the Girling was ... 05-05-2019 03:24 pm Body & interior stuff > Door Window Seals (10 replies - 12281 views) As for replacing the outer window seal:
the original(7 of them) clips work fine, by slightly widening the gap(use a steel chisel for that) and ... 03-27-2019 04:48 pm Fuel Stuff > Engine (5 replies - 7684 views) THIS IS A COPY FROM THE "FUEL PUMP" THREAD: LET"S KEEP THE COMMENT ON THAT PAGE SO WE DON"T HAVE ALL THIS DUPLICITY
The standard for ... 03-15-2019 04:58 pm Fuel Stuff > Fuel Pump vs Fuel Lines (42 replies - 44232 views) The standard for valve shimming is 12 hours of labor; the Loctite #518 cam tower-to-head anaerobic gasket cement is a less than $15, the shims ... 03-15-2019 04:54 pm Body & interior stuff > Adhesive for Delta window wipes? (8 replies - 12389 views) I wouldn't count on it; I've used that years ago with poor results, even though they looked promising at first ... 03-12-2019 11:44 pm Body & interior stuff > Adhesive for Delta window wipes? (8 replies - 12389 views) sorry; didn't realize getting it to Canada would be such a problem.
If you're close to the border, have a friend order it & then pick ... 03-09-2019 06:46 pm Body & interior stuff > convertible top installation instructions (6 replies - 8438 views) btw, i do NOT use the hollow rubber bulb that came originally on the car as it does not keep the rain from coming in ... 03-09-2019 06:23 pm Body & interior stuff > convertible top installation instructions (6 replies - 8438 views) a photo would be helpful; but the front edge gets trimmed at the first 90 degree face so that when a rubber seal goes on ... 03-09-2019 06:21 pm Body & interior stuff > convertible top installation instructions (6 replies - 8438 views) post "convertible top" in the "Search" tab at the top for help. The glue we used for the front bow is 3M "Fast Tack Trim ... 03-06-2019 04:58 pm Body & interior stuff > Adhesive for Delta window wipes? (8 replies - 12389 views) AMAZON has it in different widths:
https://www.amazon.com/s?k=3M+4929+VHB+tape&ref=nb_sb_noss ... 03-06-2019 04:22 pm Miscellaneous > Jensen Healey musings from The New York Times (10 replies - 16700 views) I forgot to mention that the SU pumps have gradually been upgraded so they are now solid state. A little pricey now at around $200, ... 02-18-2019 07:57 pm Miscellaneous > Jensen Healey musings from The New York Times (10 replies - 16700 views) Maybe now the FACET square pumps are dependable, but a over 25 years ago when they first came on the market we considered the Boat ... 02-14-2019 04:06 pm Fuel Stuff > Fuel tank vent lines...etc. (21 replies - 37820 views) I'm not sure why all the confusion: earlier gas tanks only had 2 vent tubes where the pressure relief valve is screwed in, whereas the ... 02-14-2019 03:56 pm Brakes > TR-6 Master Cylinder -Other options? (7 replies - 9687 views) I would certainly think so; no reason to sell it unless it works okay, but maybe call/email them if you want clarification ... 01-09-2019 02:53 pm Brakes > TR-6 Master Cylinder -Other options? (7 replies - 9687 views) Just looked at Martin Robey's site for J-H master cylinders; these look exactly like the originals(not sure what "EX" means for the 2nd picture). The ... 01-09-2019 02:38 am Wheels > Best Choice for Stock Tires? (7 replies - 9877 views) A few years ago, only the Vredesteins were available in a fairly high performance tire for both wet & dry pavement(the excellent Yokohama AVS were ... 01-06-2019 02:56 pm Wheels > Best Choice for Stock Tires? (7 replies - 9877 views) I've previously listed tires; please use the "SEARCH" tab at the top and type in "185-70 tires".
Both Vredestein and Pirelli. The Pirelli are ... 01-06-2019 12:45 am Fuel Stuff > Fuel Tank Sending Unit Float Puzzle (3 replies - 6216 views) yes; it was/is a common problem and the "hole" is right where the end of the metal holder/arm clasps onto the nylon. Anytime I removed ... 01-05-2019 06:40 pm Ignition > Ignition (12 replies - 15103 views) what Frank is referring to is the round white(later ones were black)"LOGIC BOX" plug right about where your left knee would be. The numbers are ... 12-27-2018 11:18 pm | |
Current time is 11:12 pm | ... 6 7 8 9 10 11 12 13 14 15 16 |