There is the large outer O-ring on the end of the shaft, then a smaller one for the plug holding the oil pressure relief spring(punch ...   08-20-2015 04:47 pm

There is the large outer O-ring on the end of the shaft, then a smaller one for the plug holding the oil pressure relief spring(punch ...   08-20-2015 04:47 pm

There is the large outer O-ring on the end of the shaft, then a smaller one for the plug holding the oil pressure relief spring(punch ...   08-20-2015 04:43 pm

Michael: try contacting Jim Reilly at 631-938-3069. He lives in Coram and has incredible knowledge of J-Hs, both strret and racing ...   08-18-2015 02:15 am

Gents: sorry for not responding sooner; John Tiesler ( JTiesler@woway.com) has done quite a bit of work with a very close replacement: the Tr7/8, TBS5514 or ...   02-09-2015 09:43 pm

Nice going! Glad to hear the other two cars were in good company!! ...   02-09-2015 07:02 pm

John: just looked at your pix; I would STRONGLY recommend you put something over your driver's side floor mat as they are "Unobtainium"(as far as ...   02-09-2015 06:12 pm

John: Mike had his own shop in California for many years. He is a super mechanic and "go-getter" for anything J-H. You would have ...   02-09-2015 06:10 pm

I use whatever high grade is available; sorry, can't help you much with that but I don't think it will greatly affect the engine ...   02-04-2015 07:14 pm

Putting each of the bearings flush with the surface of the outer casing is fine(there will be a little space in the center) but don't ...   02-04-2015 06:18 pm

In addition to our "moderator's" recommendations, I woujld also add (4 speed only) Dow CVorning "M" Gear guard to the transmission and differential. 10% ...   02-04-2015 06:12 pm

Goes to the breather tube for the crankcase, located on the top of the engine directly in front of the transmission. There should be ...   02-04-2015 06:07 pm

You can adjust the 3 door volts so there is some friction and then try to set the door. ...   06-07-2014 03:15 am

If you have SKYPE, most of these problems can be fixxed fairly easily(mine is rockclimber52). A vacuum gauge would be useful as well as ...   06-06-2014 08:29 pm

The adjustment for the doors is in the 3 bolts that go into the door itself. You will need to remove the door panel ...   06-06-2014 08:26 pm

The Jaguar's had a similar type windscreen, so maybe check for someone that does Jaguars. As for the "caulking" no one uses the rubber strips anymore ...   06-04-2014 05:13 pm

answerman: there is a very nice fix for "the bend" in the hood caused by someone inadvertantly trying to close it without lifting up the ...   03-05-2014 12:03 am

Tes--I have done it many times: Remove distributor; put old rag under opening to catch oil. Use small pin punch to push split roll pin into the ...   03-01-2014 04:23 pm

Glad to see you found the problem; for all our engine rebuilds we wrap teflon tape around the big cam wheel bolts, since, as you ...   02-28-2014 05:48 pm

Unfortunately, you're correct about the earlier front crank housings. Either update that one to the later housing(don't forget the marks are 10 degrees off ...   02-28-2014 05:02 pm

Bob: you remove the 2 sliding shafts and the small ball that actuates the electrical switch. No predrilling is necessary as the 2 bore ...   10-21-2012 03:34 pm

Jay, Bob: what Sander has done will not compromise your brake system. The 2 end caps are removed and tapped with a 1/8" tap, ...   10-20-2012 03:22 pm

Don't know if you got the timing issue solved yet from Brett, but not I would be happy to help. Do you have a webcam? ...   10-20-2012 02:55 am

Wow--nice neat engine bay--well done! ...   09-14-2012 11:34 am

Just joined and rereading all the old mail: have plenty of the vacuum operated heater valves(still gold cadmium light plating). ...   09-12-2012 01:04 am

Just joined but assume you have it plugged": standard 3/8" by 16 threads/ inch. A decent hardware store will have this in brass. ...   09-11-2012 03:29 pm

Jody: finally got logged into the JHPS web forum, something I should have done long ago; very impressed with your "HEATER BOX" videos--nice job. ...   09-10-2012 07:26 pm