The two bolts on the hood side of the hinge simply move the hood forward and back. The two bolts where the hinge attaches to ...   03-15-2013 11:47 pm

The dash cluster (or binacle as the Brits call it) with all four gauges will come out, but it can be difficult if it has not ...   01-26-2013 07:58 pm

I would look for the later 907 engine (74 and on) with the later rear seal and rebuild that engine. I'm sure if you ask ...   01-04-2013 05:15 pm

I have John's diagrams on a CD. He gave them to me when I bought his totaled JH a few years ago. If someone wants ...   10-19-2012 12:41 am

Bars Leak Head Gaskit repair. Liquid stuff in a bottle. As I recall there were two types, one type mixes with anti freeze, the other ...   06-23-2011 02:43 pm

I have seen this issue before. Coolant leaked from head gasket when first started, but would quit leaking within a minute as soon as some ...   06-23-2011 12:21 am

I recently tried to buy Valvoline VR1 at my local auto parts store for an engine I had just rebuilt (not a 907 but a ...   11-06-2010 04:23 pm

Speed bleeders are the way to go. They are available at most auto parts stores. You can bleed the brakes by yourself in 30 min ...   10-07-2010 05:58 am

From what I have seen and been told, the tapered rubber base for the four corner maker lights is correct and orignal. That is, one ...   10-07-2010 05:52 am

Reminder to all up here in the Northwest, this weekend is the 34th annual All British Field Meet. Location is Portland International Raceway, Portland Oregon. ...   08-31-2010 06:18 pm

My Pertronix only has two wires. I don't have the second strike unit. I think you need to find someone that has installed the second ...   08-11-2010 05:17 pm

OK, the Pertronix has two wires, a red and a black. The wire coming from the tach (usually the white/slate wire) is the same wire that ...   08-10-2010 10:00 pm

That is interesting. Edward and I have both been in contact with John Kimbrough and John says he took down his web page with the ...   07-08-2010 09:03 pm

I have a extra fender that is off the car. I can take pictures of it tonight and post them. (at work at the moment). The ...   06-26-2010 04:13 pm

GH, I installed my Jorge tank about a year ago. As noted several times do not use the white plastic ring he sent with the ...   06-12-2010 04:57 pm

Ed, I have a clutch alignment tool. I will send you a pm or you can send me one as I don't recall your address. ...   03-22-2010 05:49 pm

Hi Ed, Did you determine if you had the rope rear main seal, or the later one that is a typical press in round seal ...   03-06-2010 01:31 am

Gary, I recently replaced mine with new ones from Delta. The U shaped clips supplied by Delta are narrower than the originals. Try to use ...   01-02-2010 06:28 pm

This weekend the 33rd Annual All British Field Meet was held at Portland International Raceway in Portland Or. The theme of this years event was ...   09-07-2009 06:31 pm

Check your clutch cable adjustment. If you have a lot of play it might not be releasing all the way. Also if the car has ...   08-06-2009 02:41 am

I have advanced the timing  from 5 deg back to standard 10 deg BTDC and this seems to have improved my coughing and bucking problem ...   08-01-2009 09:59 pm

My car runs fine when cold and for first few miles. After driving two or three miles, it will start to idle rough,  then misses badly ...   07-20-2009 06:46 pm

With the key on it is normal to have ingintion and brake indicators on. Ignition light is connected to the alternator and goes off once ...   07-18-2009 02:21 am

The head light switch and heater switches are identical except for the label. Delta does have the orignial style, but are very expensive. They have ...   06-26-2009 02:06 am

Mine reads 14.6 volts across the battery at idle and also at 3000 rmp. 16.3 is too much. Gary ...   05-03-2009 09:26 pm

Is it a Delco Remy or Lucas ? The Delco Remy has a spacer between the pully and the fan blade. Spacer is just over ...   05-03-2009 06:22 pm

I just finished installing my Aluminum tank, also by Jorge, in to my JH. I hooked it up as Jody explains, except I did not ...   04-24-2009 02:00 am

I have a question about the early and late 4 speed differentials. I have two 74 Mark 2 cars. Both have the larger driveline flange ...   04-11-2009 07:20 pm

Thanks everyone for the comments. I was initially checking the clearance with the lobes directly opposite the cam follower.  I went back and rechecked, and ...   04-07-2009 11:01 pm

Thanks Judson, I was hoping you would respond. I will install it as is and run it for a few thousand miles and re-check clearances. ...   04-06-2009 12:29 am

I'm checking the valve clearances on the engine I bought from Ron Earp out of the IT race car. The Exhaust ones are all fine. ...   04-05-2009 02:32 am

Joachim, Good point. Previous owner may not have tightened the upper control arm bolt enough, or it came loose over the years. I will tighten ...   03-05-2009 01:44 am

My left front upper control arm is loose. I had thought the bushings were worn out. I just removed the long mounting bolt and removed ...   03-02-2009 11:15 pm

I also used a group 56. As for brands, Interstate is very good. Or you could use a dry cell Optima if they have one ...   02-20-2009 11:16 pm

Rob, not so much a concern for the springs and shocks, as it is for the tires. The tires can flat spot when sitting in ...   11-28-2008 09:00 pm

Chris, the snap mounting posts on the dash and inside windshield post would tend to indicate the car was designed for a toneau cover. Most ...   11-28-2008 05:18 pm

Ross, first I'd be sure you are turning it in the right direction. To loosen it would be counter clockwise looking at your picture. Be ...   11-28-2008 04:50 pm

OK, I finally have the PPG formulation for Malaga Blue, PPG code 14926. If you show this to your paint shop they should be able ...   10-21-2008 01:59 am

The JH originally came with the dual Strombergs in most western markets. In Europe they were available with dual Dellorto two barrels. Weber two barrels were never ...   10-19-2008 09:28 pm

I am just discovering this as well. My JH was just painted, and I'm currently re-assembling the car. I ordered new outer window rubber weatherstrip ...   10-18-2008 02:15 am