| ||||
|
Posts by Gary Martin JH 15371 | |
---|---|
98 posts | Showing posts 81-98 of 98 |
Miscellaneous > "Why did you buy a JH... When you could have bought a New sports Car?" (20 replies - 36477 views) New cars are nice, but there is just something about those old classics that a new car can't match. They're stylish, pristigous, tempramental, rare, examples ... 10-15-2005 10:51 pm Carburetors > New Aluminum Tanks - Anyone Interested? (103 replies - 78828 views) Just sent my payment with PayPal.
Thanks, Gary
... 09-15-2005 09:43 pm Carburetors > New Aluminum Tanks - Anyone Interested? (103 replies - 78828 views) Count me in too.
Gary Martin
... 09-09-2005 06:05 pm Carburetors > New Aluminum Tanks - Anyone Interested? (103 replies - 78828 views) I am also interested in a new tank. I had my old one cleaned and sealed with some red goop poured inside at a local radiator shop for ... 09-03-2005 05:46 pm Body & interior stuff > Rust Repair (5 replies - 14023 views) Working on repairing some minor rust on JH 15371. The car is really in pretty good shape rust wise. Floor boards seem fine. Only exterior ... 07-21-2005 04:10 am Body & interior stuff > Mysterious Electrical option (2 replies - 8585 views) I'm still working on old 15371. I have the gas tank out of the trunk and I'm in prosess of fixing a little rust in ... 07-21-2005 03:52 am Carburetors > Tuning Stromberg's (8 replies - 28803 views) OK, yesterday I took the choke off. I dissasembled and cleaned it up. I replaced the internal gasket (only one my kit has). Put it ... 05-09-2005 07:11 pm Miscellaneous > Leaking gas tank HELP! (5 replies - 18884 views) It took me about two hours, but I ran into a problem or two. The tank strap bolts on the trunk floor were rusted in ... 05-09-2005 06:36 pm Miscellaneous > Leaking gas tank HELP! (5 replies - 18884 views) A couple more notes on removal, as I just did this recently...
Disconnect the battery first !
After draining the tank, leave the drain plug off. This ... 05-07-2005 08:51 pm Carburetors > Tuning Stromberg's (8 replies - 28803 views) OK, I have many things to check now. I don't think I overly tightened the inlet valve. I did use the thicker Aluminum seal as ... 05-07-2005 08:23 pm Carburetors > Tuning Stromberg's (8 replies - 28803 views) I just got the engine running after 19 years out of service in JH 15371. I did not rebuild the lower end as the car only ... 05-07-2005 01:29 am Miscellaneous > Sports Rods (9 replies - 17943 views) I would aggree with Judson. I like the "evolution" idea. Nothing is wrong with a very original restoration at all, but I like the idea ... 04-22-2005 02:15 am Engine & Transmission > Clutch cable (2 replies - 9599 views) I just installed my engine and 4 speed trans yesterday. After I hooked up the clutch cable, I went to try it out and was ... 04-14-2005 06:47 pm Body & interior stuff > Body Work and Paint? (5 replies - 12738 views) I restored a 68 Camaro Z28 in 1990. After I had the car down to bare metal. I used 3M Metal Conditioner to treat it. ... 04-10-2005 12:25 am Engine & Transmission > Engine installation/removal (7 replies - 15610 views) I see from the newsletter article that the recommended way to install/remove the engine is with the transmission attached. And then to connect the exhaust ... 04-02-2005 07:49 pm Body & interior stuff > Painting (9 replies - 20436 views) Mitch, I also will be repainting my JH soon. My car had the typical enging carb fire. I already striped and repainted the engine bay. ... 03-16-2005 05:47 pm Engine & Transmission > Front and Rear main seals, timing gear removal (6 replies - 15417 views) After reading the responses mentioning I installed the seal incorrectly, I took off rear cover and removed seal. I tried to install seal from rear ... 03-16-2005 05:28 pm Engine & Transmission > Front and Rear main seals, timing gear removal (6 replies - 15417 views) Posted this on the old board and did not get much of a responce (only Greg). So lets try the new board.
While my engine ... 03-12-2005 09:22 pm | |
Current time is 04:34 am | 1 2 3 |