Yes, indeed !  The Voltmeter is supposed to tell you the battery voltage.  Just remember the gauge needle movs slowly..so, in making a small adjustment ...   01-10-2012 02:25 pm

  Nice job on repairing the voltmeters.  I have a box full of JH gauges, if you still need a good voltmeter.  If you have a ...   01-10-2012 08:32 am

Well, it seems the needle adjustment is stuck..needs to be disassembled..get a #10 O ring form a car parts store ..actually two of them if you ...   12-13-2011 11:15 am

It is there to illuminate your oil pressure gague as the pilot lamps are so dim you cannot read them at night..so they put a ...   12-06-2011 06:17 pm

I will need your email address...I write rather long treatises (often referred to as b.s.) and I do not want to load up this email ...   12-05-2011 08:58 pm

Jody:  I will send yu the copy as well...it is long as printed in the Jensen Owners Club magazine....but I need your email, as I ...   12-05-2011 07:53 pm

Fine. I would be  happy to send you the entire article, but it is too long to put on this group postings.  You would need ...   12-05-2011 07:01 pm

Well, the "Rheostat" is not a rheostat at all. It is a printed circuity board with numerous fingers or wipers that always goes bad. If ...   12-05-2011 04:51 pm

I think you fellows are confused.  The two green lamps in the gauge cluster are for right and left turn signals.  The blue one in ...   12-05-2011 04:19 pm

That's it, Jody !!!  You saved me a trip downstairs to the garage shop!  Use rubber gloves as it is hard to get off your ...   12-04-2011 04:53 pm

Yes...that will work...seems all the substitute trim will have a textured cord in it...however, it looks good...and that is what my daughter uses to make ...   12-04-2011 04:06 pm

Hmmm...looks like you go tyour work cut out for you...I strongly suggest that you find a copy of the Jensen Healey parts book.  Every part ...   12-04-2011 03:54 am

That is a very nice engine compartment.  Where did you get that blue timing belt?? Frank Schwartz ...   11-29-2011 08:36 pm

Forgot to mention, you need the adaptor with the fittings for the lines, Thadaptor munts between the oil filter and the place where a filter ...   11-06-2011 05:05 am

I have a couple of stock coolers removed from parted out cars.  No hoses, you  have to get them probably from Delta.  If yu want one of ...   11-06-2011 05:03 am

I have a pair of NOS Del Orto K&N filters 56-1320 I would like to trade for a pair to fit my Strombergs.  Anyone? Please ...   11-05-2011 11:03 pm

If Mitch doesn't want it, I'd be intersted.  Kindly contact me off line at mfsjr2@comcast.net Thanks, Frank ...   10-22-2011 08:34 am

I have a factory hard top, with heated rear window glass in good shape...but...is missing all the stainless trim except the piece that fits around ...   09-29-2011 08:03 am

It is most likely a true valid number.  Most Chrysler dealers now use a computer instead of the old books....and their computers do not go ...   09-21-2011 08:29 pm

Does anyone know the part numbers of the electric window motor assemblies that are in the Jensen GT?  These were made by Chrysler (Mopar) and ...   09-20-2011 05:26 am

Good!  Let us know when youi get thenew hose and try it.  And with new hose if it doesn't work,try reversing the hoses at the ...   08-16-2011 04:41 pm

OK, reading your post...you say the valve works by hand...good to knnw.  put the vacuum pump on it and see if that works it.  If ...   08-15-2011 08:41 pm

One more thing...you mentioned you had weak vacuum to the water valve mounted on the engine. Either one of the lines from the T which ...   08-15-2011 08:37 pm

Well, in all of the dozen or so JH's I have encountered or worked on, the metal vacuum operated valve which is attached to the ...   08-15-2011 08:33 pm

Brett:  Good to hear from you.  I have a lengthy treatise he sent me in response to some questions about the quite vague carb tuning ...   07-22-2011 03:55 pm

Hey, it looks great!  Hope you will enjoy it as much as the rest of us do ours.  You will find this group is very ...   07-21-2011 01:21 am

Some time ago, mark Rosenbaum wrote a very good article on tuning and setting up the Stromberg cqrburetors.  I cannot find it in this list ...   07-21-2011 01:19 am

The Madera parts are nice and I saw a couple of sets of them on some Jensen Healeys at the J2011E event in Lake Placid ...   06-25-2011 04:54 pm

I've got the knob with the long wire attached...do you have the outer cable and mounting in the panel> Also you need to post a picture ...   06-25-2011 05:33 am

Jody...tell memoe about the rear brake conversion to discs, please. Emay to me at mfsjr2@comcast.net Frank Schwartz ...   06-12-2011 08:37 am

Obviously yours is yellow, but the factory yellow is a bit greenish.  We repainted my daughter's JH with a Chrysler yellow called "Buttercup"..a very good ...   05-23-2011 11:26 am

Does anyone have any of the covered cardboard parts that go around the inside top covering the edges of the headliner?  The ones I have, ...   03-31-2011 02:17 am

If you will contact me off line at mfsjr2@comcast.net  I will send you my original article with the correct measurements and some good photos of ...   03-25-2011 03:54 am