Hey Greg I'm still not getting the newsletter which is not too suprising in that you have not deposited my check #1095 dated Aug 2 2016 ...   09-17-2016 03:22 pm

Joachim   The project looks great!  You mentioned doing a bit of work on the brakes and that reminded me of the time my daughter-in-law came ...   07-23-2016 08:37 pm

Does anyone have a suggestion for making the doors shut with that satisfying ker-chunk.  I have the windows and the associated hardware removed and I ...   08-26-2009 01:10 am

13753 feels so much better now.  It had been ailing for a while with a problem others may have had.  Someone, who shall remain nameless, broke off ...   08-26-2009 12:57 am

In my earlier post I failed to mention that the 60 series tires now on 13753 provide noticeably better steering response even at low inflation ...   03-08-2008 10:55 pm

George   They were neither expensive nor hard to make but then again I have worked in and around machine shops most of my life.   Probably the ...   02-10-2008 06:59 pm

13753 is now wearing a set of Miata wheels and they don't look too bad.  If anyone wants to look I can post a photo ...   02-09-2008 11:02 pm

Many blasting shops offer an alternative to sand or glass bead when it comes to removing paint from aluminum.  It is baking soda.  The blaster ...   06-04-2007 09:45 pm

smc   I do have a center cap which I will sell to you IF you promise not to burn it. How does $5 + ship ...   05-23-2007 12:59 am

Mitch   My JH was acting the same way (firing when the key is released) and the problem was that the ballast resistor was not being ...   05-02-2007 09:48 pm

Some time back I posted a complaint abt 13753 being hard to start.  Once started, it ran great.  Turns out to be a very simple ...   04-29-2007 01:49 am

Dish   Be aware that the seam sealer that Art mentioned is some world class stuff ! I had to make a thin chisel out of ...   02-23-2007 01:11 am

Greg   Do you still have the old Koni's around and if so would you sell them?                                        Tom 13753 ...   12-21-2006 10:54 pm

Guys   Twice in this thread I have seen mention of Koni Shocks.  The Koni importer says no listing exists for the JH.  What application are ...   12-19-2006 10:24 pm

Judson:   The reliabilty part I get; no points to burn etc.  It's the starting, economy, power and emissions that have me wondering.  These all seem ...   12-02-2006 10:25 pm

I've been thinking that I may not know all that I thought I knew about ignitions.  What SPECIFIC benefits do I get from a "high ...   12-01-2006 10:37 pm

13753  Good running cond  eng 6631 16971  In process-stripped completely down 16036  Parts car All in central Indiana    Tom Thomson  ...   11-13-2006 10:44 pm

Jim   I am reluctant to disagree with the expert but a defective hose may not be as rare as you think.  I have experienced this twice ...   09-23-2006 09:52 pm

Bob:   I had trouble with the door fit and it turned out to be that the car was bending.  The jump seat/package shelf at the ...   08-20-2006 12:08 am

Bob:   What a great looking car.  13753 looks just like yours except for the rollbar and the hood fit.  How did you get that hood ...   08-18-2006 07:19 pm

Tom   I believe that Mark has the answer on your brake problem.  After my daughter-in- law came back trailing smoke from the rear brakes, I ...   08-11-2006 01:38 am

TX   I could not find a good spot on the floor of 16971 to check but the driveshaft tunnel mikes .048 or 18 ga.  I ...   12-24-2005 04:35 pm

Ron  13753 had a steering shaft U-joint which was in bad shape but I took it apart and pressed in new bronze bushings which I got ...   11-28-2005 12:43 am

George   We all have heard about joints that require no lubrication. Yeah right!  But not to worry cause you can get a hypodermic needle that ...   11-10-2005 09:46 pm

13753 starts quickly if it was driven yesterday but if I let it sit for a few days it is an absolute bear.  Choke (enrichment) ...   09-22-2005 12:01 am

Actually Sport, if you will take a look at axel (axle) and hub flanges you will discover that there are no thinck (thick) spots at ...   08-30-2005 07:44 pm

I am seeing lots of messages about adapters and spacers.  It would require some amount of teardown but why not drill new stud holes on ...   08-23-2005 01:25 am

Me too - #13753          Tom          tthomson@tls.net ...   08-07-2005 01:31 am

A while back, just as my old computer was was in it's death throes, someone sent a message abt the availabilty of old style ( ...   06-23-2005 12:54 am

I have an extra heater which could be had for a pittance.  However, since working under the dash is equivalent to getting a root canal, ...   04-21-2005 01:14 am

Mark:  I have a pretty grundy set of lug nuts which are yours for shipping cost if you want them.                               Tom - 13753   ...   04-16-2005 01:45 am

Ron   I too, have a spare engine which is just taking up floor space.  Drop a line if you have any interest.               Tom - 13753 ...   04-16-2005 01:41 am

John:   I found lots of neat stuff on the  (very well done) web page, but nothing on the Pertronix????  By the way, yours is the ...   04-05-2005 02:00 am