Home 
Home Search search Menu menu Not logged in - Login | Register
> Ron Mau

Profile Topics Posts
Posts by Ron Mau
61 postsShowing posts 41-61 of 61

Ignition > Spark plugs (3 replies - 6856 views)

I have been having problems with my spark plugs going bad and not firing. I have switched to Petronix ignition with the high output coil. ...   08-30-2006 02:21 pm

Cooling > Delta's heater-valve conversion from vacuum to mechanical (16 replies - 16441 views)

I put a manual shut off on my heater hose  When it get's cold just turn the valve on and you have heat. How's that ...   08-22-2006 03:46 am

Ignition > No spark (2 replies - 4853 views)

Thanks Colin, I just came in from the garage and you were right on the money. Replaced the spark plug and all is well now. Thanks, Ron ...   08-02-2006 03:30 pm

Ignition > No spark (2 replies - 4853 views)

I have no spark in the #4 cylinder. I have switched to petroinix ignition. I switched out  the plug wire . Still no spark. I ...   08-02-2006 03:45 am

Electrical & Instruments > REMOVAL OF KEY IGNITION SWITCH FROM STEERING COLUMN (4 replies - 5904 views)

I used a dremel and cut a slot into the snap off head and then used a screwdriver to remove the bolt. Ron Mau ...   07-11-2006 03:29 am

Body & interior stuff > What are these nuts and bolts going to? (3 replies - 4553 views)

HI Greg, I think I have that part. I,ll let you know and drop it in the mail.   Ron Mau ...   01-25-2006 11:19 pm

Engine & Transmission > oil pressure at highway speeds (5 replies - 5455 views)

Judson, Different engine, but I don't want the same outcome. Ron Ron ...   01-18-2006 10:09 pm

Engine & Transmission > oil pressure at highway speeds (5 replies - 5455 views)

Last summer after rebuilding the top end of an engine, I took it out on the highway the oil pressure was at 65 pounds and ...   01-18-2006 02:21 am

Body & interior stuff > Steering wheel question (6 replies - 7155 views)

Use some heat from ahair dryer or a paint remover to heat up the rubber and then it will come quite easily and not leave ...   11-01-2005 11:43 pm

Electrical & Instruments > panel light switch (10 replies - 10271 views)

I found it on Ebay. I don't remember if it was in the US or UK. You just need to keep checking. You could get ...   09-07-2005 11:08 pm

Electrical & Instruments > panel light switch (10 replies - 10271 views)

I have a new dimmer switch for my dash lights. Does any one know how to remove the knob? I don't want to mess it ...   09-07-2005 12:47 am

Engine & Transmission > 16367 Lives again (2 replies - 4270 views)

Well after 3 months 16367 is back in running condition. I swiped the engine from another car. Rebuilt the head and reassembled the car. It ...   08-27-2005 04:36 am

Electrical & Instruments > Location of reverse light switch (12 replies - 9421 views)

I found that the ground at the light wasn't quite good enough to ground the light so Iwould check there also. Use a short piece ...   08-17-2005 11:32 pm

Engine & Transmission > JH heads (7 replies - 7877 views)

I have decided that my restoration project would loan it's engine to my other car. No $ for a major rebuild. After a compression check(# 2 ...   05-03-2005 12:36 am

Engine & Transmission > Crankshaft (12 replies - 10190 views)

This will be my first venture inside of the engine. Where do you split the block. Do I need to take the engine completely out. ...   04-19-2005 06:53 pm

Engine & Transmission > Crankshaft (12 replies - 10190 views)

The play is for and aft (front to rear). I checked and the crankshart does move when you push and release the clutch. Ron ...   04-19-2005 06:22 pm

Engine & Transmission > Crankshaft (12 replies - 10190 views)

Hi Judson, The oil pressure is at 40- 50 psi, I did notice that the iol pressure at highway speeds did seem a litle lower than ...   04-19-2005 03:47 pm

Engine & Transmission > Crankshaft (12 replies - 10190 views)

While driving my car rather hard, Revved to about 6000 rpms.It developed a loud clattering sound. Now that I have examined the car, I have ...   04-19-2005 03:26 pm

Suspension > Front suspension (45 replies - 37495 views)

Hi all, Rear suspension done. now on to the front. Any tips or advice to make the job easier? It looks to be more complicated than the rear. Thanks, Ron ...   03-26-2005 03:30 am

Suspension > Suspension bolts (13 replies - 11771 views)

The rear ones, the bolts don't fit. Time for a trip to the parts store.   Ron ...   03-22-2005 03:08 am

Suspension > Suspension bolts (13 replies - 11771 views)

While replacing the bushings on my suspension, I found that the bolts no longer fit. They seem to be too large to fit through the ...   03-21-2005 02:41 am


 Current time is 04:40 pm
 First Page Previous Page  1  2 


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems