Home 
Home Search search Menu menu Not logged in - Login | Register
> Glen

Profile Topics Posts
Posts by Glen
21 postsShowing posts 1-21 of 21

Engine & Transmission > What the heck is this noise? (4 replies - 9655 views)

  Hey .. get this .. the noise was the fan against the radiator shroud.  Every time I'd torque the engine, it was just enough to ...   10-15-2006 07:08 am

Engine & Transmission > What the heck is this noise? (4 replies - 9655 views)

U-joints were replaced when I put in the 4 speed... had to put in a different drive shaft.  Good idea, though ...   09-30-2006 06:12 pm

Engine & Transmission > What the heck is this noise? (4 replies - 9655 views)

I've got this mystery noise noise coming out of my engine/transmission.  It sounds like something spinning against metal.  I usually hear it when the transmission is ...   09-29-2006 09:41 pm

Engine & Transmission > New noises (1 reply - 5961 views)

I had the same symptoms and heard the same noise in my 5 speed.   If you have a 5 speed as well, then we probably ...   08-31-2006 11:40 pm

Engine & Transmission > back to that 5 speed getrag repair (11 replies - 25952 views)

How about instructions regarding taking the getrag apart? anybody? ...   08-22-2006 11:09 pm

Engine & Transmission > back to that 5 speed getrag repair (11 replies - 25952 views)

So ... nobody knows how to take these apart and see what's wrong?  It might be some part that can be machined or something.  It ...   08-21-2006 12:40 am

Engine & Transmission > back to that 5 speed getrag repair (11 replies - 25952 views)

Anyone know where we Northern California folks can get it fixed?  If not, where can we find out how to fix it ourselves.  Has anyone ...   08-19-2006 02:39 am

Engine & Transmission > shifter problems - no reverse (1 reply - 6384 views)

  I recently replaced the clutch and the car drove fine a couple times.  The third time I drove it, I was uable to shift into ...   04-28-2006 05:21 pm

Ignition > starter and selenoid connections (7 replies - 20045 views)

Veiy odd indeed. I did take the selenoid off the starter and cleaned the copper piston inside and applied some WD40 because it seemed to ...   01-29-2006 03:32 am

Ignition > starter and selenoid connections (7 replies - 20045 views)

What would cause the white-yellow wire not to go to 12+ volts when the car key is turned to the start postion? ...   01-28-2006 09:23 pm

Ignition > starter and selenoid connections (7 replies - 20045 views)

  Still not working: Ok .. first this was a running car (#19667) that I replaced the clutch plate, throwout bearing and pilot bearing on.  The battery ...   01-28-2006 08:17 pm

Ignition > starter and selenoid connections (7 replies - 20045 views)

I wanted to clarify my understanding of how the electrical connections on the starter motor are made. My car doesn't have, nor has it ever had ...   01-28-2006 03:34 am

Engine & Transmission > Clutch Gaitor Availablity (6 replies - 13110 views)

I've obtained one of those mr. gasket rubber gearshift boot things and it seems to fit really well.  I cut off the base of it and one ...   01-19-2006 10:00 pm

Engine & Transmission > Speedometer cable connection (1 reply - 6609 views)

I'm getting the transmission put back in am need a little help with the details.   How exactly do I put the  speedo cable into the transmission and make sure ...   01-19-2006 08:13 pm

Engine & Transmission > Clutch Gaitor Availablity (6 replies - 13110 views)

Anyone know where to get a gaitor (gaiter, gater, gator,??) for the clutch pivot arm?  What are people using for this? ...   01-06-2006 06:26 am

Engine & Transmission > Clutch noise/failure to dissengage (3 replies - 8665 views)

My clutch started making a noise like a bolt being pulled through sheetmetal.  It did this when the clutch was fully engaged and at low speeds ...   07-18-2005 06:43 pm

Suspension > Front suspension (53 replies - 90376 views)

  Just my 2 cents worth: I did the front suspension without a press.  I used a drill to drill a bunch of holes in the ...   03-29-2005 06:37 pm

Miscellaneous > New to this JH business (4 replies - 11967 views)

  I would consider the following factors: 1)condition of the floorboards are the main concerns with which body you select.  These often have extensive rust under those carpets.  ...   03-25-2005 06:34 am

Electrical & Instruments > Headlight Relays (3 replies - 11429 views)

What does a relay do that allows it to reduce the current that flows through the delicate, expensive JH instrument switches?  How does it work?   #19667 ...   03-23-2005 07:25 am

Body & interior stuff > Bodywork and Paint question (4 replies - 11206 views)

Maaco 1) uses cheap paint that will fade by the sun in 2 years. 2) Doesn't do any bodywork at those cheap quotes. 3) Doesn't strip the car ...   03-21-2005 06:49 pm

Suspension > Suspension bolts (13 replies - 24350 views)

I just recently redid the front suspension bushings that I got from Delta and don't recall any bolts that didn't fit.  Which bushings are you ...   03-21-2005 06:21 pm


 Current time is 04:51 am
 


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems