If clutch actuation didn't effect noise then trans problem seems unlikely. My rattle(s) after engine/trans R&R this Spring were 1.The sheet metal piece that covers ...   11-30-2020 06:42 pm

Does operating the clutch change the sound? ...   11-30-2020 01:06 pm

Delta carries them. Bought one from them last month. ...   08-21-2020 01:55 pm

Yes, it happened to me as well. I cut off a piece of a magnet, so I ended up with a small rectangular piece. I ...   08-12-2020 01:50 pm

Problem solved. One brake shoe was a little too wide, like just a few millimeters. The outer metal edge of the shoe was ...   07-27-2020 08:22 pm

Girling type. Left rear Click, Click, Clicks as I slow down approaching stop, last 30 feet or so. Could be happening at higher speeds but ...   07-23-2020 05:28 pm

I'd very much like to see that. I replaced those nylon pieces a number of years ago but can't visualize the construct. Yesterday I removed ...   06-14-2020 02:33 pm

Thanks everyone. Appreciate the quick answers and comments. ...   06-14-2020 01:12 pm

So I'm clear on your approach, you left the upper u-joint on the steering shaft connected to the steering column as it comes out of ...   06-13-2020 05:15 pm

Am making plans to remove and replace engine. LHD. Two piece header. Can I leave the header and the steering shaft attached during the process? ...   06-13-2020 02:44 pm

I need one cam carrier. Just one. If you've got one you'd be willing to part with please let me know. ...   04-13-2020 01:17 pm

I have a set of main bearings for a 1974 Mark II. All the bearings have a grove running through them. They are Vandervell stamped ...   03-28-2020 08:45 pm

Before I did mine I read all the posts and asked a lot of questions. I was so hopeful I could use a puller I ...   03-19-2020 06:11 pm

Currently running a Lotus 907 stock engine with choked down Dellorto 45's. Would like to get more torque but can't swing the 2.2 stroker-HC piston-big ...   02-25-2020 11:23 pm

I can confirm (through cutting into two separate junked sets) that there are at least two possible IDs. 1/2" and 5/8" ...   10-25-2019 03:05 pm

Thanks, but I'm hoping someone has cut one open so I can get an accurate measurement . I am planning on splicing in a preluber ...   10-03-2019 09:49 pm

Anyone know the inside diameter of the hoses that go to and from the oil cooler? ...   10-03-2019 04:13 pm

Early version of front bumper, the smaller metal one. There is a chromed plastic strip that was riveted on to the bottom as a cosmetic ...   09-29-2019 01:22 pm

Exactly what I was seeking. Thank you very much. ...   09-23-2019 04:48 am

Does anyone have a diagram of the engine's lubrication system? ...   09-22-2019 06:41 pm

Did you mean to say "No, if you're not going to pull the transmission out to do it" I don't intend to pull the transmission ...   09-13-2019 11:46 pm

Do you need to remove the transmission cross-member to get at the seal? ...   09-13-2019 02:35 pm

Thanks. Other opinions? ...   05-07-2019 03:07 pm

If you had a choice between Lockheed or Giriling brakes on the rear axle, which would you choose and why? ...   05-04-2019 07:13 pm

Are the brake drums "universal"? Will brake drums fit on either a Lockheed or Girling set-up, or do Girling brakes call for a different drum ...   05-04-2019 12:04 am

Seeing the offer on their website was what prompted my inquiry. I'm wondering if any owners have purchased a unit and used it? Looks good, ...   01-09-2019 01:55 pm

The TR-6 master cylinder seems to be everyone's go-to for replacement. I know it bolts right in, but have also read about fluid seeping out ...   01-08-2019 08:48 pm

Thank you Sander. Have you had any trouble getting them balanced properly? ...   01-07-2019 12:14 am

Thank you for linking me up to your previous post. Which one did you have on your car, Vredestein or Pirelli? Why did you choose ...   01-06-2019 02:50 pm

Am interested in purchasing a new set of tires. Would like to go with stock size: 185-70-13. Care most about ride and balance (have had ...   01-05-2019 11:01 pm

I live in a condo in Seattle but keep the car at a beach house on the rural Oregon coast, 4 ½ hours away. So, ...   11-12-2018 04:39 pm

Thanks, I'll look it over. One thing that makes me reluctant is the ability to get the proper parts. When I purchased the car the ...   11-10-2018 09:31 pm

Thank you,this has been very helpful. It's clear that undertaking a project of this magnitude will not only be expensive but also require the services ...   11-09-2018 01:52 pm

My question about if they are rebuildable has been answered. The bearings are available, but at a steep price. Two follow-up questions: 1. Does replacing the ...   11-09-2018 12:31 am

4 speed approaching 120K. Differential is noisy and sloppy. Loudest going downhill. When rear of car is up on jack stands and I rotate one ...   11-08-2018 12:45 am

Sent you an email but not sure it went through. If you could send me the photo that would be great. Please email to: Steve@DuncanLabs.com. I'm ...   04-12-2018 11:23 pm

Yes, the front left and right are the same. Look forward to hearing from you. Thanks ...   04-12-2018 01:58 pm

Just had the Spax shock on the front left corner lock-up. Anybody have one siting around they'd like to part with? ...   04-10-2018 09:36 pm

Thanks for sharing your experiences. Unfortunately the car is in a rural area on the Oregon coast so entrusting it to a shop is ...   04-01-2018 07:04 pm

Replacing the rear suspension bushings. Lower arms were easy. Hole saw to cut through old rubber, then sawsall to cut through metal cylinder that was ...   03-31-2018 11:02 pm