Home 
Home Search search Menu menu Not logged in - Login | Register
> h2oman

Profile Topics Posts
Posts by h2oman
19 postsShowing posts 1-19 of 19

Engine & Transmission > Cam belt tensioner bearing replacements (8 replies - 6235 views)

Thanks everyone for the part numbers and advice. These bearings seem to be widely available and at a variety of prices. I ordered some up ...   11-28-2012 04:05 am

Engine & Transmission > Cam belt tensioner bearing replacements (8 replies - 6235 views)

My tensioner bearings are noisy and need replacement. Has anybody cross referenced these bearings so they can be sourced locally? I want to purchase them ...   11-21-2012 01:27 pm

Brakes > Leaky brake valve (8 replies - 9256 views)

Thanks for the response Bruce. When you say you tap the opening, are you talking about the end caps themselves, the end cap openings, or ...   10-21-2012 03:04 pm

Electrical & Instruments > Horn, headlights blinkers repaired (9 replies - 7965 views)

John's electrical diagrams are already on the club site at http://www.jensenhealey.com/members/archive/electrical/index.html Only members can access this using a password. Once I saw an article he wrote ...   10-19-2012 02:12 am

Electrical & Instruments > Horn, headlights blinkers repaired (9 replies - 7965 views)

Since there have been requests, I have posted the wiring diagram for Headlight wiring with relays. I used John Kimbro's excellent diagram #10 and modified ...   10-14-2012 11:46 pm

Electrical & Instruments > Ballast Resistor test? (1 reply - 3264 views)

I went out and measured my ballast resistor and it was about 2 ohms resistance with nothing connected to it. The ballast resistor is in the ...   10-14-2012 10:11 pm

Electrical & Instruments > Horn, headlights blinkers repaired (9 replies - 7965 views)

For once, I'm not asking for help. By reading the excellent posts by others that went before me, I now have functioning horn, headlights and ...   08-14-2012 04:13 am

Carburetors > Dellorto accelerator pumps (9 replies - 10741 views)

Thank you everyone for the advice. Since it is running close to perfectly, with only a slight hesitation now that I increased the accel. pump ...   08-01-2012 06:42 pm

Carburetors > Dellorto accelerator pumps (9 replies - 10741 views)

Thanks for the response Greg - My carbs were purchased new in 1991 from Dave Bean as a kit with the manifold and 2 carbs. They ...   07-27-2012 02:21 pm

Carburetors > Dellorto accelerator pumps (9 replies - 10741 views)

Joachim - Thanks for the prompt reply. I have noticed that once it is reved up, no problem. I know that this setup can be ...   07-15-2012 07:55 pm

Carburetors > Dellorto accelerator pumps (9 replies - 10741 views)

I rebuilt my Dellorto's and my engine is running nearly perfectly. It starts easily cold, and runs flawlessly in the driveway. It idles beautifully after ...   07-15-2012 02:03 pm

Brakes > Leaky brake valve (8 replies - 9256 views)

Thanks for the response. I was just thinking about removing the PDWA and using a coupling and tee to replace it. Several people have done ...   07-07-2012 10:31 pm

Brakes > Leaky brake valve (8 replies - 9256 views)

I have a 74 JH-5 and have several fluid leaks coming from the Brake pressure differential warning actuator (PDWA). One leak is out of ...   07-06-2012 04:20 am

Fuel Stuff > Gas cap replacement seal (3 replies - 7053 views)

The gasket for the gas cap arrived today and fit perfectly on my original gas cap. It took some wd-40 and wiggling it to get ...   07-25-2011 08:10 pm

Fuel Stuff > Gas cap replacement seal (3 replies - 7053 views)

I ordered the rubber gas cap gasket today from Moore's Cycle Center (http://mcctriumph.com in Anaheim today. The gasket was $5 + shipping+ tax. I will update ...   07-22-2011 10:22 pm

Fuel Stuff > Gas cap replacement seal (3 replies - 7053 views)

I am working on my fuel system and the original locking fuel cap is in great shape except for the rubber seal. In looking around ...   07-22-2011 01:35 am

Engine & Transmission > Oil pressure gauge hose? (1 reply - 2666 views)

My hose to the oil pressure gauge has been gnawed on by a critter, and is now in half. I am interested in replacing the ...   04-19-2011 02:46 am

Ignition > how to get cam timing correct (1 reply - 4068 views)

I was replacing my timing belt and thought thought I was done with it. I had the engine at 90 deg after TDC while replacing ...   04-09-2011 09:30 pm

VIN Database for Jensen Healey & Jensen GT > Jensen Healey & Jensen GT VIN Database (280 replies - 249326 views)

1974 JH-5 VIN: 19695 Miles: 72648 Condition: Running, needs interior restoration and paint Location: Mariposa, CA Owner: Bob Waterman since 1986 Color: Red, was White from the factory ...   07-11-2010 05:05 am


 Current time is 10:45 am
 


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems