Ok, maybe I should start a new thread w/ 'changing your oil pump' as the topic. Greg - feel free to move this if ...   12-17-2005 11:32 pm

Check the latest Delta specials sheet. They comment that a new distributor unit will be available after the 1st. I heard this from ...   12-17-2005 01:11 am

I don't know the details but I do know that Pertronix is supposed to come out w/ an entire distributor for the 907. I ...   12-16-2005 10:34 pm

JH - thanks for the comments. My only question is - if there is indeed a lack of spark at high temp - what would ...   12-13-2005 05:24 pm

sitting in the pub last nite i discussed this problem w/ a motorhead acquaintance of mine. he agreed about the wear on the oil ...   12-13-2005 04:36 pm

I think I have most of the gremlins out of the ignition system. I have not driven the car in a while as I've ...   12-12-2005 08:14 pm

For rubber products check out McMaster Carr (http://www.mcmaster.com/). I have bought several different rubber products from them over the years for use in repairing ...   12-01-2005 05:31 pm

nvandal: i'd like to learn more about the rear disc brake conversion. if you get the chance please start a new thread. after i ...   10-26-2005 07:08 pm

thanks for the info guys. i'm back in town (for a couple of days anyway. . ) so i'll play around a bit and ...   10-26-2005 07:00 pm

Thanks for some good ideas. I ran a wire from the battery to the coil and drove her around for a bit - no ...   10-19-2005 09:58 pm

So do page 3 girls all drive Jensens?? I knew I like this car! Ok, it still cuts out. And when it does it's ...   10-16-2005 12:23 am

Ok, my fuel filters were in BAD shape. So I swapped them out. I drove around for 1/2 hour or so (all within ...   10-13-2005 08:33 pm

fuel filter is on the 'to check' list as well. but it stops so suddenly i wonder if that's it. but, it vill ...   10-11-2005 09:38 pm

One of these days I'll actually be DRIVING this car instead of sitting alongside the road w/ it. . . Interesting problem. I ...   10-11-2005 04:15 pm

There's a brand used dist lised on ebay. I wish it had been there last week - I'd of bought it instead of spending ...   10-05-2005 11:49 am

Thanks for the comment. I think I have other places to spend my $$ and time. ...   10-04-2005 02:15 pm

I thought I saw someone post info on an aluminum radiator for the JH. Anyone know of one that's available? I may just ...   10-03-2005 05:25 pm

Update. Thanks for all the comments guys. I was being a bit flippant about not knowing all the wires on the coil. I ...   10-03-2005 04:58 am

I called pertronix a couple of days ago and got the same response. I was waiting to post until after I installed the brand ...   09-27-2005 08:34 pm

Brett: I don't think so - but I'll check again. I hooked it up the way it was wired before I put in the new ...   09-23-2005 03:45 pm

I think i'm going to buy points and condenser and start from there. if that doesn't work. the only thing i can think ...   09-23-2005 07:07 am

I can swap plugs but - even if the plugs aren't firing - there should at least be fire thru the wires. ...   09-23-2005 12:26 am

Damn, this is turning into quite a hassle. But, it's a hobby not a car - right? I must admit I've learned a ...   09-22-2005 10:57 pm

Good advice. 1) The plug wires are new - but there could be a problem I guess - I'll swap some wires and see what happens. 2) ...   09-20-2005 06:00 pm

the car is running quite smoothly - on 2 cylinders. it's running so nicely on those two cylinders it will sit and idle. ...   09-20-2005 12:27 am

Mark: I come to the same conclusion. The website doesn't have ANY info for someone to contact. My coil is 3.0 ohms. ...   09-17-2005 12:31 am

And the 60,000 question is - does the Pertronix Flamethrower coil need a ballast resistor? ...   09-16-2005 03:46 pm

I was correct. At idle I'm getting 9.5 volts max. I'm playing by myself so even with my unsteady hand and the flashlight. ...   09-16-2005 02:21 am

It seems to me that if someone answered George's question - it would help me out!! I'm off to check what voltage I'm getting ...   09-16-2005 02:11 am

Back to the drawing board. With the new wires, plugs (gapped at 40-45), rotor, cap, coil and pertronix there is a MARKED inprovement. ...   09-16-2005 01:00 am

Sent payment via PayPal. Joel ...   09-15-2005 11:51 pm

my car has a 4spd overdrive tranny. i can't remember the name of the mfg but it's the common euro fit. when i ...   09-15-2005 05:56 am

Just an aside: I just got back from Japan. Apparently 13" wheels are readily available there - in many sport variations. ...   09-13-2005 11:29 pm

I agree within reason. If you had a good supply of like fiber replacements (airdam etc)that didn't look horrible I'd be interested. ...   09-11-2005 01:53 pm

Awesome. It's good to give something back after all the info I've gotten from this board in the last few weeks. ...   09-09-2005 12:40 am

As before, I'm in. I'm in Japan until next week but can drop a check anytime after that. If necessary I can pay ...   09-08-2005 08:18 am

I am out of town for a week but can meet him in person in 10 days or so. Do your best. Then ...   09-06-2005 08:16 am

Brad: No worries. Thanks for chatting w/ Jorge. Harkes - you should be able to ship international for 100 bucks. As long as ...   09-05-2005 09:53 pm

Looking back over the thread I have: The yeas at: me Majic Switch Hawkes PChung Jensen4U Dan Collier The 'maybes': Don Panini Jim ...   09-02-2005 04:37 pm

If I can get 10 people committed - I'll call him up and try to negotiate. Maybe Greg (I'm bettting you're reading this) would ...   09-02-2005 06:27 am