Well, took the red beast back to the Dragon hillclimb. With boost, some sticky new tires etc I was after the Two Minute Club. Saturday ...   09-13-2015 07:31 am

Those are XXR 513's. http://www.xxrwheel.net/xxr_513.shtml They are 15x8 but only available in a 4x100 or 4x114.3 bolt circle. :-( I have Miata knuckles and hubs ...   05-31-2015 10:44 pm

Been a lot happening, but the car hasn't been ignored. It's now Rustoleum Sunrise Red. It's a '50/50' paint job: looks great 50 feet away ...   05-13-2015 01:48 pm

Your description of the smoking problem does indicate a ring, rather than a valve guide, problem. I once disassembled a Ford 2.3 which had the ...   04-27-2015 05:39 pm

Valve stem excessive clearance will cause serious smoke this way: on deceleration in gear the throttles are closed which increases manifold vacuum. If there's any ...   04-25-2015 12:58 pm

I would Helicoil it back to the stock size, then use a stud and nut instead of a bolt. Aluminum is soft and not really ...   04-25-2015 12:47 pm

If anyone needs it, I have a 5 speed Getrag bellhousing left over from my W58 swap. Everything else related has been sold. I also ...   03-25-2015 08:06 pm

By the way, about the speedometer cable: I don't know about European transmissions but over here there's a limited number of speedometer gears for the ...   03-25-2015 08:02 pm

Stock 907 with Dellortos and a Crane ignition. It was pretty obvious on the first test drive the 3:45 rear axle did not allow the ...   03-23-2015 09:18 pm

I have a drill guide which I bought when a cylinder head bolt broke while disassembling an Isuzu Trooper V6. It was definitely accurate enough ...   03-23-2015 09:12 pm

I did a W58 in my JH5, the first time I drove it with the 3:45 axle I went hunting for a 3:73. Now that ...   03-22-2015 09:51 pm

Barthol wrote: Found the error. I ran the engine for a little while closed the throttle and just rolled to a stop in 2 gear,then immediately removed ...   03-22-2015 09:36 pm

I got a pair of those thick rubber splash guards for a pickup and cut approx 1" wide slices. http://www.northerntool.com/shop/tools/product_200316137_200316137 Painted the outside of the ...   03-22-2015 09:30 pm

Yes, it's normal. Dellortos have a high idle provision which is nothing more than a poorly controlled and noisy vacuum leak. Use it as little ...   11-05-2014 11:44 am

Glad to hear the heart beats on! I like the 907 and have one in 19015, my reasoning for the rotary swap for the race ...   09-13-2014 02:13 pm

Thought I'd add a couple pics of the now much busier engine bay. http://img.photobucket.com/albums/v248/jensenman/100_1538_zpsd6a00871.jpg http://img.photobucket.com/albums/v248/jensenman/100_1537_zps78a51c73.jpg The next big project is rerouting the exhaust, it will come out ...   09-08-2014 06:19 pm

The car looks great! I did the GT hood prop thing on mine when I got it, the bonnet was in good shape but I ...   08-31-2014 01:16 pm

That's what I thought. Thanks for the info! ...   08-16-2014 05:31 pm

It looks like I might actually get a Jensen GT to bookend my roadster. As is normal it will get a timing belt water pump ...   08-16-2014 11:45 am

Oh, I will be back driving again soon. I'm already signed up for the February LeMons at Barber Motorsports Park! No, I won't be driving ...   08-13-2014 06:39 pm

Mitch, hate to hear the motor blew. Ron had a catastrophic driveshaft failure and, as I discovered when taking things apart, something big broke in ...   08-09-2014 01:13 pm

    Been a few changes to the car since the last post. It now sports a 13BT (single turbo 13B rotary) and a 4:30-1 gear set. ...   07-16-2014 02:13 pm

Here's a lesser vehicle :-D having issues at the same spot in August. http://www.youtube.com/watch?v=Ylk7eJ_rjjM ...   08-24-2013 04:41 pm

Video from the first run of the second day, which is the last run I got in before the car got bent. At 1:28 in ...   07-20-2013 12:52 pm

Hope this link works! This is from the Chasing the Dragon Hillclimb in Robbinsville, NC on 6/23/13. That's my co driver having a Code Brown ...   06-25-2013 02:16 am

I have finally found some time to put into this project again. I didn't really like the instrument panel I first built, so I decided ...   11-01-2012 08:40 pm

I'm looking for a used fiberglass bonnet for this project, a boot lid would be nice too. 1974jh5mws@gmail.com Thanks! ...   10-14-2012 02:08 pm

Looking for a used fiberglass bonnet for my race car project. I have an un-bent steel one which needs some repair that I'll be glad ...   10-14-2012 02:06 pm

Dells (and for that matter any carb) should have an immediate 'pump shot'. This means when you look in the venturis with a light and ...   07-21-2012 11:28 pm

I have an aftermarket but the trim is not the same. Check this place http://southcoastautocenter.com/ ask for Louis, he has (IIRC) 4 J-H's and I ...   05-29-2012 10:08 pm

It should. It dropped my engine temps from ~205-210 on the highway to ~185-195. ...   05-24-2012 03:58 am

I made an aluminum 'extension' for the stock lower radiator opening which channels air into the radiator. It's not pretty but it really helps with ...   05-20-2012 08:27 pm

FWIW: the W58 conversion would be a lot simpler without the odd shaped front housing. When I was doing mine, I couldn't help but wonder ...   05-20-2012 07:57 pm

Not much, unfortunately. Moved to another city and of course the cars went with me, things are settling down now. I can't find sticky enough ...   04-07-2012 12:25 am

My other cars over the years? 1971 Dodge Charger. Chrysler products are known for front end parts wearing quickly and this car supported that. No kidding. ...   01-08-2012 08:00 pm

Huh. VTO doesn't show a 4x4 bolt circle, but if they are available inthat pattern I might be trading my 14x6 Minilites in... ...   12-06-2011 12:38 am

http://64.27.130.204/vtowheelsv1/wp-content/uploads/2011/09/15x6-Retro-4-Silver-website.jpg I always thought these would look good on a J-H. It's a VTO Retro 4, an American Racing Libre reproduction but sadly not available in ...   12-04-2011 06:46 pm

I went the same route Steve057 did, I mounted a pivot on the opposite side of the bellhousing from the stock Lotus setup and modified a ...   12-04-2011 06:29 pm

An S10 rear can be used, but when I built my rotary powered J-H from a retired SCCA IT car I found that a Mazda ...   12-03-2011 09:00 pm

What do you make the shims from, stainless shim stock? And do you cut them by hand? ...   12-03-2011 08:54 pm