Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Suspension > Lower Front Arm strengthening

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Lower Front Arm strengthening  Rate Topic 
AuthorPost
 Posted: 09-20-2021 01:10 am
  PM Quote Reply
1st Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 650
Status: 
Offline
Here's good advice for anyone redoing their front suspension. The lower arm has 2 pices of support for the bolt on the backside, but only one "meager" support for the front of the bolt(see pix). For all the one I redo, I cut a circular piece of 1/8" + metal(one inch diameter or a little more is fine) to add strenght to the tremenduous force put on this area(see pix).
Hope this helps, bruce[img][/img]

Attachment: J-H front subframe lower arm welded support.jpg (Downloaded 107 times)

Back To Top PM Quote Reply  

 Posted: 09-20-2021 01:10 am
  PM Quote Reply
2nd Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 650
Status: 
Offline
[img][/img]

Attachment: J-H front subframe lower arm welded support.jpg1.jpg1a.jpg (Downloaded 103 times)

Back To Top PM Quote Reply

 Posted: 09-20-2021 01:11 am
  PM Quote Reply
3rd Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 650
Status: 
Offline
[img][/img]

Attachment: J-H front subframe lower arm welded support.jpg1.jpg2.jpg3.jpg (Downloaded 103 times)

Back To Top PM Quote Reply  

 Posted: 09-20-2021 01:11 am
  PM Quote Reply
4th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 650
Status: 
Offline
[img][/img]

Attachment: J-H front subframe lower arm welded support.jpg2.jpg (Downloaded 103 times)

Back To Top PM Quote Reply

 Posted: 08-03-2023 12:59 am
  PM Quote Reply
5th Post
dbeliveau74
Member


Joined: 12-28-2015
Location: Manchester, New Hampshire USA
Posts: 53
Status: 
Offline
This must be the where the lower arm mounts to the cross member.

Back To Top PM Quote Reply  

 Posted: 08-03-2023 01:11 am
  PM Quote Reply
6th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 650
Status: 
Offline
This the FRONT of the subframe where the lower bolt for the lower arm goes through. The rear already has extra metal from the part that attaches to the lower frame, so it is not needed there

Back To Top PM Quote Reply

 Posted: 08-03-2023 01:45 am
  PM Quote Reply
7th Post
dbeliveau74
Member


Joined: 12-28-2015
Location: Manchester, New Hampshire USA
Posts: 53
Status: 
Offline
Thats what I thought, I'm replacing the front suspension
bushings, trying to get as much info as possible. Top fulcrum bolt is being stubborn, lower was installed backwards so I'll have to drop the steering rack.
Welding that metal on the crossmember won't change the geometry? Had to order new spring seats since they loo,ed pretty bad, so I also ordered new upper and lower fulcrum bolts and nuts. I'm thinking I'll have to cut the bolts off so better to get prepared.
One issue I have is torquing the fulcrum bolts with wheels on the ground. How to get up there? I'll probably Jack up the lower arm to take the weight!

Last edited on 08-03-2023 01:48 am by dbeliveau74

Back To Top PM Quote Reply  

 Posted: 08-03-2023 02:10 am
  PM Quote Reply
8th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 650
Status: 
Offline
Some car ramps that support the wheels would allow you to slide underneath to torque the upper wishbone bolts. The rear of the car should be jacked up to a level height with the front, but you wouldn't need ramps for that

Back To Top PM Quote Reply

Current time is 10:08 pm  
> Jensen Healey & Jensen GT Tech > Suspension > Lower Front Arm strengthening Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems