Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Ignition > Lucas 25d distibutor body

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Lucas 25d distibutor body  Rate Topic 
AuthorPost
 Posted: 11-09-2020 11:59 am
  PM Quote Reply
1st Post
rschlemm
Member
 

Joined: 04-19-2019
Location:  
Posts: 4
Status: 
Offline
the area on the distributor (aluminum) where the steel ring secures the distributor to the oil pump has fractured and can no longer be secured with the retaining ring. I had previously used JB Weld to hold these pieces together but it broke over the weekend. I knew it was on borrowed time when i put it together, but wanted to enjoy the car over the summer.

Can the Moss 25D distributor for the MG be used, transplanting the guts from my distributor into the new body? Or can a later distributor body be used?

Back To Top PM Quote Reply  

 Posted: 11-09-2020 02:05 pm
  PM Quote Reply
2nd Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 409
Status: 
Offline
basically, yes(the 5 digit # stamped on the front may be different, but you will need to transfer the guts; might as well change the seal while you're in there)
btw, I have MANY good used ones and I'm sure others do as well

Back To Top PM Quote Reply

 Posted: 11-10-2020 12:30 pm
  PM Quote Reply
3rd Post
rschlemm
Member
 

Joined: 04-19-2019
Location:  
Posts: 4
Status: 
Offline
if anyone has a good 25D distributor body for sale send me a PM.

Back To Top PM Quote Reply  

 Posted: 11-10-2020 02:36 pm
  PM Quote Reply
4th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 785
Status: 
Offline
If you are going to have the dizzy apart don't forget to add the inner oil seal update, if you need details go to Jensen-Healey on Facebook, in the files section.
Brett.

Back To Top PM Quote Reply

 Posted: 11-10-2020 03:23 pm
  PM Quote Reply
5th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 409
Status: 
Offline
As I previously as stated, I have quite a few. I don't know if you want to rebuild it yourself, or have me do It (I have probably rebuilt well over 100). Try me at my regular email; RedRacerbm@gamil.com as that will be much faster to respond

Back To Top PM Quote Reply  

 Posted: 11-10-2020 10:18 pm
  PM Quote Reply
6th Post
DonBurns
Member
 

Joined: 09-18-2015
Location: Fullerton, California USA
Posts: 98
Status: 
Offline
On my first JH (14313) I was forever having the 25D pop out when I loosened to adjust the timing. It may have been because the skirt was already cracked, but anyway it finally broke completely. I took to a friendly machine shop and they cut away the aluminum skirt and replaced with a press fit steel sleeve. I asked them to add a very slight raised "catch" at the end. Just enough that the pinch clamp would catch and I could loosen the clamp and turn the distributor without having to worry about it popping out on me, which as you know makes for a bigger project. I could still remove the distributor by putting a flat screwdriver at the end of the clamp and twisting. Has anyone else done this?

Back To Top PM Quote Reply

 Posted: 11-10-2020 11:42 pm
  PM Quote Reply
7th Post
discogodfather
Member


Joined: 09-17-2007
Location: San Francisco, California USA
Posts: 161
Status: 
Online
I didn't add a lip but I do add a small turned steel ring into the gap between the edge and the main body so that it has something to clamp against. Seems to be working well. I might try that idea of just machining it all away and adding a larger steel ring, that would be probably the best thing.

It's just an awful design in general, thought many times of doing something custom that had a tab that attached to the oil pump housing and another tab on the distributor and just bolt it together, similar to every other car company did with a brain.

Back To Top PM Quote Reply  

Current time is 10:43 pm  
> Jensen Healey & Jensen GT Tech > Ignition > Lucas 25d distibutor body Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems