Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Suspension > Fitting rear Superpro bushes

 Moderated by: Greg Fletcher Page:  First Page Previous Page  1  2   
New Topic Reply Printer Friendly
Fitting rear Superpro bushes  Rating:  Rating
AuthorPost
 Posted: 11-29-2014 11:17 pm
  PM Quote Reply
21st Post
Eric
Member
 

Joined: 11-11-2014
Location:  
Posts: 35
Status: 
Offline
Okay have the rear suspension apart. Bushings on lower control arms came out as described elsewhere..no problem. Question is..how do I get the bushings out on the differential side of the upper control arms? Not much room to work there. Do I drill the rubber out and use the hacksaw like I've done for the other bushings , or can they be pounded out? Not sure I can get a drill in that space.

Eric

Back To Top PM Quote Reply  

 Posted: 11-30-2014 01:25 am
  PM Quote Reply
22nd Post
Eric
Member
 

Joined: 11-11-2014
Location:  
Posts: 35
Status: 
Offline
Or perhaps some sort of bushing puller??

Back To Top PM Quote Reply

 Posted: 12-01-2014 02:37 pm
  PM Quote Reply
23rd Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
Pound them out with a long piece of wood an d a heavy hammer. The metal jacket protrudes from the mount. Use lots of penetrating oil!

Back To Top PM Quote Reply  

 Posted: 12-14-2014 09:22 pm
  PM Quote Reply
24th Post
Eric
Member
 

Joined: 11-11-2014
Location:  
Posts: 35
Status: 
Offline
Im using the Delta bushings at the rear. As others have noted, the crush tubes are too small for the bolts. Appears that the correct diameter is about 7/16". Is this correct? Do I just drill them out with a drill press? Also, on my car, 3 of the 4 bolts holding the upper and lower control arms on each side are identical, but the 4th has a slightly different locking nut. It is this way on both sides. As I assumed they were all identical, I have no idea which location the 1 "different" nut goes on each side. Thoughts?

Thanks!
Eric

Back To Top PM Quote Reply

 Posted: 12-14-2014 10:02 pm
  PM Quote Reply
25th Post
Jim Picot
Member
 

Joined: 07-09-2012
Location: Melbourne, Australia
Posts: 39
Status: 
Offline
I would say the "different" nut was what came to hand the last time the suspension was pulled down.  I used all-new hardware right throughout, so everything matches. Oh...and use an anti-sieze when re-assembling. The next person to pull it down will thank you - and that may be you!

Back To Top PM Quote Reply  

 Posted: 12-14-2014 10:27 pm
  PM Quote Reply
26th Post
Eric
Member
 

Joined: 11-11-2014
Location:  
Posts: 35
Status: 
Offline
What size drill bit did you use for the crush tubes? Looks to be about 7/16" in my estimation.

Back To Top PM Quote Reply

 Posted: 12-14-2014 11:35 pm
  PM Quote Reply
27th Post
Jim Picot
Member
 

Joined: 07-09-2012
Location: Melbourne, Australia
Posts: 39
Status: 
Offline
I don't recall drilling any crush tubes. The bolts I had to replace the originals (same size) fitted nicely, and yes, I think they were 7/16" UNF.

I used Superpro bushes, not Delta-supplied bushes.

Back To Top PM Quote Reply  

 Posted: 12-15-2014 12:09 am
  PM Quote Reply
28th Post
Eric
Member
 

Joined: 11-11-2014
Location:  
Posts: 35
Status: 
Offline
The super pro I used for the rear upper control arms worked fine with the bolts. Its the Delta bushings that are too small.

Back To Top PM Quote Reply

Current time is 07:32 am Page:  First Page Previous Page  1  2     
> Jensen Healey & Jensen GT Tech > Suspension > Fitting rear Superpro bushes Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems