Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Electrical & Instruments > Defeating the seat belt interlock

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Defeating the seat belt interlock  Rate Topic 
AuthorPost
 Posted: 06-01-2005 09:16 pm
  PM Quote Reply
1st Post
andrewo
Member
 

Joined: 06-01-2005
Location: San Diego, California USA
Posts: 51
Status: 
Offline
I know that this was covered ad nauseum on the old board, but I never printed it out. Can someone tell me how to defeat the ignition interlock and buzzer? As I recall, it involves pulling the logic box plug and jumping two posts.

Thanks - Andrew

Back To Top PM Quote Reply  

 Posted: 06-02-2005 01:54 am
  PM Quote Reply
2nd Post
Mark Rosenbaum
Member


Joined: 03-12-2005
Location: Kingman, Arizona USA
Posts: 532
Status: 
Offline
Yep, that's all.  Pull the round plug, then jumper pins 11 and 12.  This connects the START wire from the ignition switch to the hot side of the coil on the relay used to activate the starter solenoid.

Alternately, pull the round plug, then connect pin 12 to an 'Engine Start' pushbutton such as that used in the Honda S2000.  The second side of the button would be wired to a source of switched or direct battery voltage, perhaps with an added inline fuse.

Attachment: red button.jpg (Downloaded 153 times)

Back To Top PM Quote Reply

 Posted: 06-05-2005 05:55 am
  PM Quote Reply
3rd Post
andrewo
Member
 

Joined: 06-01-2005
Location: San Diego, California USA
Posts: 51
Status: 
Offline
Okay, I have placed a wire connecting those two, but do I need to do it in a way that allows the plug to go back in? I assume that there are other things running through that plug. Should the car be able to start with the plug out and the jumper in place?

Thanks - Andrew

Back To Top PM Quote Reply  

 Posted: 06-05-2005 04:03 pm
  PM Quote Reply
4th Post
Mark Rosenbaum
Member


Joined: 03-12-2005
Location: Kingman, Arizona USA
Posts: 532
Status: 
Offline
With pins 11 and 12 jumpered, and with the round plug disconnected and in a plastic bag to avoid short circuits, the car will start and run normally.  However, you will lose the functions of (a) the 'door open and key in ignition' buzzer, and (b) the 'fasten seat belts' warning light and buzzer.

If you're comfortable with altering the car's electrical system, you can remove all of the wiring associated with the infamous seat belt warning system and make a permanent connection between the wires that once ran to pins 11 and 12 of the round plug.  This involves unwrapping and rewrapping the wiring harness, and therefore is most easily done when the dash has been removed for some reason.  You'll want to save the blue tape used to wrap the wiring, as it can be re-used once cleaned of dust and grime.  IIRC this tape is also available from British Wiring.

The 'door open and key in ignition' audible alarm can easily be restored.  The buzzer used on European JHs for this purpose was still available from Delta Motorsports a few years back, and as it's unlikely this is a fast moving item, they should still have plenty on hand.  Alternately, you could use a junkyard / aftermarket chime, buzzer, bell, horn, or whatever else suited your fancy.

The 'fasten seat belts' function can be restored if one adds the appropriate (but expensive) aftermarket gadgetry.  Alternately, you could make contact with JH owner Frank Schwartz, who some years ago was looking into designing a circuit for the task.

However, a better use for the warning light might be to provide some new function such as indicating low oil pressure, low fuel level, hood or trunk lid ajar, door ajar, or whatever else suited your fancy.  The legends giving the functions of the warning lights are thin plastic films, clear text on black background, and if you have access to a laser printer that will deal with transparency films, you can make new legends with whatever text you wish.  Wiring, of course, would depend on what you had in mind.

 

Back To Top PM Quote Reply

 Posted: 09-17-2019 07:46 pm
  PM Quote Reply
5th Post
Spaceman
Member


Joined: 05-30-2017
Location:  
Posts: 25
Status: 
Offline
that makes no sense, your WR wire from ignition goes thru the round plug, therefore it needs to be plugged back in for the voltage from the key, to get to the seat belt relay?

Back To Top PM Quote Reply  

 Posted: 09-24-2019 04:21 pm
  PM Quote Reply
6th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 649
Status: 
Offline
Actually it does work: the WR wire goes through the "LOGIC" box to see you have all the necessary items hooked up, such as your seat belt on and the door closed, so the current can go back through the #12 wire to the relay by your left knee and onto the solenoid on the starter.
Basically, you are cutting out this "Ralph Nader" garbage(like the pressure differential switch which has been described as well in another article I wrote years ago).
This was written up over 40 years ago in the WHITE LADY magazine and almost every car I have seen or worked on will have this done.

Back To Top PM Quote Reply

 Posted: 10-15-2019 04:15 pm
  PM Quote Reply
7th Post
noomg
Member
 

Joined: 08-02-2018
Location: Long Beach, California USA
Posts: 451
Status: 
Offline
Andrew,

You still have a function interlock system in your car?

Back To Top PM Quote Reply  

Current time is 03:45 pm  
> Jensen Healey & Jensen GT Tech > Electrical & Instruments > Defeating the seat belt interlock Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems