Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Wheels > I'm going with 16's and I'm not sure what offset

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
I'm going with 16's and I'm not sure what offset  Rate Topic 
AuthorPost
 Posted: 08-10-2006 07:28 pm
  PM Quote Reply
1st Post
britter
Member
 

Joined: 08-01-2006
Location:  
Posts: 13
Status: 
Offline
Looking at these wheels in 16x7 and 16x8...What backspacing do I need?

 

 

http://www.diamondracingwheels.com/RoadRaceSeries.htm

Back To Top PM Quote Reply  

 Posted: 08-10-2006 09:18 pm
  PM Quote Reply
2nd Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
 

Just use the search function to get all the wheel info that's been posted.

 

http://www.jensenhealey.com/forums/view_topic.php?id=487&forum_id=12&highlight=wheels

Back To Top PM Quote Reply

 Posted: 08-13-2006 04:09 am
  PM Quote Reply
3rd Post
Ron Earp
Member


Joined: 03-12-2005
Location: Cary, North Carolina USA
Posts: 339
Status: 
Offline
16", IMHO, would be a bad idea.  It'd get you nothing over traction that you couldn't get with careful selection of rubber (I've got 225s on the stock wheels, far too big), and, it'd get you a lot of unspring weight and gear reduction.  The latter two you do not want in the 2L, or 2.2L cars. b

Back To Top PM Quote Reply  

 Posted: 08-13-2006 07:33 am
  PM Quote Reply
4th Post
britter
Member
 

Joined: 08-01-2006
Location:  
Posts: 13
Status: 
Offline
Actually I need gear reduction...I have 375 horsepower and a 373 rear...that's why I was thinking 16's

Back To Top PM Quote Reply

 Posted: 08-13-2006 01:15 pm
  PM Quote Reply
5th Post
Ron Earp
Member


Joined: 03-12-2005
Location: Cary, North Carolina USA
Posts: 339
Status: 
Offline
Ah, you've the Chevy motor. Run that thing on a chassis dyno yet? Be interested to see how it pans out at the rear wheels.   You might want some larger wheels, but you won't get much gear reduction out of larger wheels and tires.

Is it a stock JH rear end? Not much difference in rear gear ratios available for the JH rear. You could go to a narrowed Ford 7.5" or 8.8", or even a 9" rear and have whatever gear ratios needed on the cheap!

Back To Top PM Quote Reply  

 Posted: 08-13-2006 11:31 pm
  PM Quote Reply
6th Post
britter
Member
 

Joined: 08-01-2006
Location:  
Posts: 13
Status: 
Offline
Yes it's a tock rear end...I should have ot tuned up by next week and then I 'll post some numbers...I'm thinking about a Ford 9", just curious about how to bolt it in there...Back to the welder I guess....the 373 sure is fun though...

Back To Top PM Quote Reply

 Posted: 08-14-2006 03:49 am
  PM Quote Reply
7th Post
Pat Connor
Member


Joined: 03-12-2005
Location: San Dimas, California USA
Posts: 21
Status: 
Offline
For your information  a rear end out of a Chev S10 or GMC Sonoma width wheel flange to wheel flange is 54 inchs the same as the Jensen Healey and comes with either 9.5" x 2" drums or discs.  I am at present installing one in my Jensen- Healey Chev.  The lower control arms can be used with the brackets off the Jensen allowing use of the stock springs and shocks. However the upper arms cannot be used as stock due to the wider and taller Chev casting.  I am at present deciding whether to modify the Jensen upper arms or go to a conventional four link setup and a Panhard rod.

Back To Top PM Quote Reply  

 Posted: 08-14-2006 05:58 pm
  PM Quote Reply
8th Post
Ron Earp
Member


Joined: 03-12-2005
Location: Cary, North Carolina USA
Posts: 339
Status: 
Offline
Hmmmm.........................Pat that is some good information, thanks!

Ron

Back To Top PM Quote Reply

 Posted: 08-14-2006 06:46 pm
  PM Quote Reply
9th Post
Pat Connor
Member


Joined: 03-12-2005
Location: San Dimas, California USA
Posts: 21
Status: 
Offline
I have also learned that their was a Torsen LSD available as an option for the 1998 Camaro and Firebird which uses the same axel.

Back To Top PM Quote Reply  

Current time is 05:28 am  
> Jensen Healey & Jensen GT Tech > Wheels > I'm going with 16's and I'm not sure what offset Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems