Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Brakes > Lockheed Brake Shoes Installation

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Lockheed Brake Shoes Installation  Rate Topic 
AuthorPost
 Posted: 09-14-2021 08:00 am
  PM Quote Reply
1st Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Hopefully, this will make your installation easier & faster.
First, we assume you have cleaned the shoes and put a VERY light smearing of brake grease on the 2 pins, the washers, and the parts that slide on the metal. The first picture shows the tools necessary; the special brake shoe pliers are not necessary(unless you like using them), but are used to REMOVE the shoes). Basically, the needle nosed plier and a #0 round screw driver are all that I need.[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg (Downloaded 23 times)

Back To Top PM Quote Reply  

 Posted: 09-14-2021 08:02 am
  PM Quote Reply
2nd Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Start with the rear/trailing shoe. Slip it onto the emergency brake tab and into the slot on the wheel cylinder piston.

Attachment: J-H Lockheed brake shoes installation.jpg1.jpg (Downloaded 23 times)

Back To Top PM Quote Reply

 Posted: 09-14-2021 08:03 am
  PM Quote Reply
3rd Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg2.jpg (Downloaded 23 times)

Back To Top PM Quote Reply  

 Posted: 09-14-2021 08:06 am
  PM Quote Reply
4th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Take the spring shown(the one that goes behind the toothed adjuster) as pictured. I would advise that you spread the lower toothed adjuster a bit for now; later, you'll close that before putting on the final spring.[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg3.jpg (Downloaded 23 times)

Back To Top PM Quote Reply

 Posted: 09-14-2021 08:11 am
  PM Quote Reply
5th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Now snag the corresponding hole with the other end of the spring on the rear shoe, and pull the front/leading shoe into its wheel cylinder piston slot.[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg5.jpg (Downloaded 23 times)

Back To Top PM Quote Reply  

 Posted: 09-14-2021 08:13 am
  PM Quote Reply
6th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Install the hold-down for the rear shoe.[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg6.jpg (Downloaded 23 times)

Back To Top PM Quote Reply

 Posted: 09-14-2021 08:16 am
  PM Quote Reply
7th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Take the upper spring and first place an end into the rear shoe hole BEHIND the shoe. Then place the other end into the corresponding hole of the front shoe.[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg7.jpg (Downloaded 23 times)

Back To Top PM Quote Reply  

 Posted: 09-14-2021 08:17 am
  PM Quote Reply
8th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
With your fingers, now push the front shoe into its upper slot.[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg8.jpg (Downloaded 23 times)

Back To Top PM Quote Reply

 Posted: 09-14-2021 08:19 am
  PM Quote Reply
9th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg9.jpg (Downloaded 23 times)

Back To Top PM Quote Reply  

 Posted: 09-14-2021 08:20 am
  PM Quote Reply
10th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Install the spring hold-down for the front shoe[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg10.jpg (Downloaded 23 times)

Back To Top PM Quote Reply

 Posted: 09-14-2021 08:23 am
  PM Quote Reply
11th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Before installing the final spring(here's where the small rounded screwdriver is used), lift up the upper toothed adjuster and push the lower adjuster all the way in(i.e. make the diameter for the shoes as small as possible)[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg11.jpg (Downloaded 23 times)

Back To Top PM Quote Reply  

 Posted: 09-14-2021 08:25 am
  PM Quote Reply
12th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Finally, take the last spring and start it over the handbrake metal piece as shown[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg12.jpg (Downloaded 23 times)

Back To Top PM Quote Reply

 Posted: 09-14-2021 08:26 am
  PM Quote Reply
13th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Now use the screwdriver over the other end of the spring and "lever" it into the hole ABOVE the spring already there.[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg13.jpg (Downloaded 23 times)

Back To Top PM Quote Reply  

 Posted: 09-14-2021 08:27 am
  PM Quote Reply
14th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 517
Status: 
Online
Your final picture should look similar to this:[img][/img]

Attachment: J-H Lockheed brake shoes installation.jpg14.jpg (Downloaded 24 times)

Back To Top PM Quote Reply

Current time is 12:13 am  
> Jensen Healey & Jensen GT Tech > Brakes > Lockheed Brake Shoes Installation Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems