Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Fuel Stuff > Fuel sender replacement

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Fuel sender replacement  Rate Topic 
AuthorPost
 Posted: 06-20-2017 01:14 pm
  PM Quote Reply
1st Post
stuartmorgan
Member


Joined: 05-07-2013
Location: Melbourne, Australia
Posts: 39
Status: 
Offline
Hi all
I replaced my fuel sender with a NOS one that I bought that came with the new seal and voltage balancer
It worked great, so I filled it further, until it got to over half full and the leak appeared from under the lock ring boss, only slowly but enough
So I bent theta sin further, got a flat blade next to one of the tab bases and tapped it further around clock wise until it basically stopped
It seems to have halted the leak, so here's my question (s)

I've never removed this type of ring lock before, only flange types
I cheated and removed it with tank in situ, so I had to prise ring out and then flatten it again toner use
Are they actually meant to work like a helical ie screw back into that opening or are the tabs supposed to bent to hold it there or are the tabs just to have something to grip while turn
Ning
I keep checking it in cares it leaks

Oh and one other thing, the fuel hoses coming off the top of the tank and on the right hand side look original, with those twist wire clamps ( fuel pump connector hoses are new) the older hoses aren't leaking, should I leave them un disturbed??
Cheers
Stu

Back To Top PM Quote Reply  

 Posted: 06-20-2017 03:10 pm
  PM Quote Reply
2nd Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 313
Status: 
Offline
Stu:
Those hoses are over thirty years old...prevent a leak in the future...replace them with new hoses.. The old "an ounce of prevention" thing, you know..
Regards,
Frank

Back To Top PM Quote Reply

 Posted: 06-20-2017 04:18 pm
  PM Quote Reply
3rd Post
Screenplay
Member
 

Joined: 07-12-2013
Location: San Francisco, California USA
Posts: 124
Status: 
Offline
Hi Stu,
It sounds as if what you've done is correct - tapping those tabs until the lock ring is tight and not bending them. It's always good to keep an eye on it for a while but after some time has passed with no leaks I'd say it's good to go.

I completely agree with Frank on the hoses... replace them all while you're in there. It's a low pressure environment and they are sheltered from the elements, but they're old and they can and will get brittle, especially if the car is in any heat.

Cheers,
Clinton

Back To Top PM Quote Reply  

 Posted: 06-20-2017 07:01 pm
  PM Quote Reply
4th Post
Jim Ketcham
Member
 

Joined: 03-13-2005
Location: Salt Point, New York USA
Posts: 208
Status: 
Offline
When replacing the hoses remember the anti-siphon hose has a check valve embedded in it. Don't throw it out. It can be cut out and installed in your new hose.

Back To Top PM Quote Reply

 Posted: 06-20-2017 11:44 pm
  PM Quote Reply
5th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 646
Status: 
Offline
Stu:
1) the tabs on the locking ring are just for getting it on and off(screwdriver works well)
2) Jim pointed out the very important anti-siphon valve(about the size of a 22 caliber bullet) located in the end of the line going to a "T" at the top left side of the gas tank. There should be the fuel line running from the electric pump going into this "T" at 90 degrees and exiting on the opposite side going to the carbs.(Earlier gas tanks did NOT have this anti-siphon valve and could leak gas through the carbs if the gas tank was higher than the carbs, such as when sitting on a steep downhill, nose first)

Back To Top PM Quote Reply  

 Posted: 06-21-2017 12:27 pm
  PM Quote Reply
6th Post
stuartmorgan
Member


Joined: 05-07-2013
Location: Melbourne, Australia
Posts: 39
Status: 
Offline
Thanks frank I think your right
I will do it as a weekend winter mental relaxation job
Stu

Back To Top PM Quote Reply

 Posted: 06-21-2017 12:28 pm
  PM Quote Reply
7th Post
stuartmorgan
Member


Joined: 05-07-2013
Location: Melbourne, Australia
Posts: 39
Status: 
Offline
Thanks frank
I did read about this and saw pics on an old blog
Stu

Back To Top PM Quote Reply  

 Posted: 06-21-2017 12:31 pm
  PM Quote Reply
8th Post
stuartmorgan
Member


Joined: 05-07-2013
Location: Melbourne, Australia
Posts: 39
Status: 
Offline
Thanks Clinton
Hopefully I it doesn't start leaking again
I put a bore scope in and took a look above and below baffles
It was clean, no real debris, but some rust spots starting, but not bad, pretty good actually considering age
Stu

Back To Top PM Quote Reply

 Posted: 06-21-2017 12:34 pm
  PM Quote Reply
9th Post
stuartmorgan
Member


Joined: 05-07-2013
Location: Melbourne, Australia
Posts: 39
Status: 
Offline
Hi Bruce
Thanks mate
Can you guys advise the fuel hose size for these lines and are they all the same size hose and barbs??
I had some fuel hose left over from when I did the Interceptor, but it's too big in Dia
Stu

Back To Top PM Quote Reply  

 Posted: 06-21-2017 01:05 pm
  PM Quote Reply
10th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
pretty sure 5/16"

Back To Top PM Quote Reply

 Posted: 06-21-2017 01:48 pm
  PM Quote Reply
11th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 646
Status: 
Offline
Fuel line to "T" is 5/16"; the plastic/black nylon lines have reducer rubber(1/8" I think) going to the charcoal cannister in front. (be sure that line is "OPEN" or you will create a gas tank vacuum).
btw, forgot to mention in the previous email that we use #2 Permatex on both sides of the black rubber gasket to ensure against gas leaks from the sending unit/pick-up tube hole.

Back To Top PM Quote Reply  

Current time is 02:10 pm  
> Jensen Healey & Jensen GT Tech > Fuel Stuff > Fuel sender replacement Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems