Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Fuel Stuff > thickness of material for under gas tank

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
thickness of material for under gas tank  Rate Topic 
AuthorPost
 Posted: 10-02-2016 01:21 am
  PM Quote Reply
1st Post
Bfitz241
Member


Joined: 02-05-2015
Location: Saint Augustine, Florida USA
Posts: 169
Status: 
Offline
I read through this thread
http://www.jensenhealey.com/forums/view_topic.php?id=1930&forum_id=14
and saw people use varied things under the tank.
I'm thinking about using 3/16" thick material, either rubber or some type of nylon.
Think that is a reasonable thickness ?

Back To Top PM Quote Reply  

 Posted: 10-02-2016 02:15 pm
  PM Quote Reply
2nd Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
You can use a lot of things under the tank, but just keep in mind "Air flow", should it get wet under there it needs to dry. Brett

Back To Top PM Quote Reply

 Posted: 10-02-2016 05:50 pm
  PM Quote Reply
3rd Post
Tom Bradley
Member
 

Joined: 07-15-2013
Location:  
Posts: 203
Status: 
Offline
3/16" thick sounds about right. I used some felt padding that was around 5/16" or so and it was too thick. I had to remove some of the rubber from the fill tube to get it to fit. Felt generally is not recommended because it can hold moisture which can cause rusting, but my tank had a good paint job when I re-installed it and it made slipping the tank in and out much easier than rubber. Any material that is flexible enough to fill in the gaps between the tank and the frame should be fine. Nylon seems like it might be too stiff for this.

There also is supposed to be some padding between the tank and the backside of the cockpit. I used 1/4" cork, which put the drain somewhat forward of the center of the hole in the frame. I think 1/2" is what it is supposed to be.

Back To Top PM Quote Reply  

 Posted: 10-02-2016 10:25 pm
  PM Quote Reply
4th Post
Bfitz241
Member


Joined: 02-05-2015
Location: Saint Augustine, Florida USA
Posts: 169
Status: 
Offline
that's good info..Thanks I will act accordingly...

Back To Top PM Quote Reply

 Posted: 10-03-2016 06:19 am
  PM Quote Reply
5th Post
Tom Bradley
Member
 

Joined: 07-15-2013
Location:  
Posts: 203
Status: 
Offline
Forgot to mention: There is also supposed to be a rubber grommet in the drain hole in the chassis. This helps keep any moisture from getting in from underneath the car. I forget the size, but it was fairly easy to find. The grommet I found was thinner than the padding I had, so I added a bead of silicone to complete the seal after I had everything settled in.

Back To Top PM Quote Reply  

 Posted: 10-03-2016 06:32 am
  PM Quote Reply
6th Post
answerman
Member
 

Joined: 09-10-2012
Location: Little Chute, Wisconsin USA
Posts: 435
Status: 
Offline
I used sections of 12/2 Romex (residential building cable, what you've got for all the wiring in your house most likely). Cut about 4 sections of it about a foot apiece, laid them in place, and then set the fuel tank on them. No, it's not "concours" but it's not like anyone will ever see it with the carpet in place and it's something almost every homeowner has lying around.

Back To Top PM Quote Reply

 Posted: 10-03-2016 07:22 am
  PM Quote Reply
7th Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 313
Status: 
Offline
If you use felt, just remember that it will really soak up water and hold it ...and then...rust.... I cut strips from those cheap rubber bungee straps and glue about three of them down on the floor and let the tank rest on them...

Back To Top PM Quote Reply  

 Posted: 10-04-2016 11:58 am
  PM Quote Reply
8th Post
Paul Koehler
Member


Joined: 04-06-2005
Location: Malone, New York USA
Posts: 94
Status: 
Offline
A simple extension cord, cut to the proper length, is about the right thickness, and because of its composition (copper and plastic) will not itself corrode or contribute to galvanic corrosion, because of the plastic insulating the two different metals

Back To Top PM Quote Reply

 Posted: 10-04-2016 07:55 pm
  PM Quote Reply
9th Post
Screenplay
Member
 

Joined: 07-12-2013
Location: San Francisco, California USA
Posts: 124
Status: 
Offline
In addition to the material under the tank, be certain the gasket around the filler tube is as good as can be well. Delta has replacements, and I have to wonder if there is a good installation trick to help keep the water out in the first place.

Back To Top PM Quote Reply  

Current time is 02:16 pm  
> Jensen Healey & Jensen GT Tech > Fuel Stuff > thickness of material for under gas tank Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems