Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher Page:    1  2  Next Page Last Page  
New Topic Reply Printer Friendly
Webers or ?  Rating:  Rating
AuthorPost
 Posted: 08-18-2014 02:59 pm
  PM Quote Reply
1st Post
tallyhoe
Member
 

Joined: 08-17-2014
Location:  
Posts: 29
Status: 
Offline
I am a new owner of a JH so please be patient. I am looking for direction on the what is the best process to check out the condition of the units. Apparently an old owner did some performance work of dubious quality. I am after just a good driver. I am an old BMC mech and know SU and Zenith carbs well. No experience on Webers. Any idea n where to start? The engine kinda runs at idle and nothing else.
Thanks anyone who helps.

Back To Top PM Quote Reply  

 Posted: 08-19-2014 02:00 pm
  PM Quote Reply
2nd Post
Paul Koehler
Member


Joined: 04-06-2005
Location: Malone, New York USA
Posts: 94
Status: 
Offline
Beg,borrow, buy or steal Des Hammond's book on Dellorto's & Weber carbs; read it  3 or 4 times or enough times until it starts to sink in and then have at it with your Webers. Alternately, find a set of ZS carbs( E-bay or most people who have made the switch to Dells/Webers have at least one set laying around), install on your new find, and enjoy the car while you learn the mysteries of Webers.

Back To Top PM Quote Reply

 Posted: 08-19-2014 03:27 pm
  PM Quote Reply
3rd Post
tallyhoe
Member
 

Joined: 08-17-2014
Location:  
Posts: 29
Status: 
Offline
I was afraid of that. Anybody ever change them to SUs? Yah, right. It off to Ebay for me. thanks

Back To Top PM Quote Reply  

 Posted: 08-19-2014 04:09 pm
  PM Quote Reply
4th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
The carbs may be gummed up due to sitting. A rebuild kit, float adjustment, and a good cleaning should get them back to normal.

I would first check the compression, timing, cam alignment, and clean the points if they're still in there.

90% of carburetor issues are ignition.

Welcome to the board! Kurt

Back To Top PM Quote Reply

 Posted: 08-19-2014 04:16 pm
  PM Quote Reply
5th Post
tallyhoe
Member
 

Joined: 08-17-2014
Location:  
Posts: 29
Status: 
Offline
Thanks. It is gummy. No Points a Pirahana electronic is installed but I will pull it apart farther in a day or so to see what is really there. Where is the best place for a carb kit.

Back To Top PM Quote Reply  

 Posted: 08-19-2014 04:56 pm
  PM Quote Reply
6th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
Weber carb kits are readily available. Your location should determine your supplier.
http://www.piercemanifolds.com/default.asp
http://www.webercarbsdirect.com/

Back To Top PM Quote Reply

 Posted: 08-19-2014 04:59 pm
  PM Quote Reply
7th Post
tallyhoe
Member
 

Joined: 08-17-2014
Location:  
Posts: 29
Status: 
Offline
Thanks again. USA. Minnesota. I am suspicious of a compression problem from exhaust notes, however.

Back To Top PM Quote Reply  

 Posted: 08-19-2014 08:24 pm
  PM Quote Reply
8th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
I have several heads with burnt exhaust valves. I suspect the engines didn't have proper maintenance since adjusting valves on the 907 is so difficult and time consuming.

The stock pistons are 8.5:1 and the cams have a lot of overlap, so don't expect compression readings over 130psi.

A leak down test should help identify the issue, unless your engine has multiple problems.

When I got my car the leak down showed air leaking past the rings blowing out the breather tube. Also air leaking through the exhaust valves into the exhaust system. I did a total rebuild.

Back To Top PM Quote Reply

 Posted: 08-19-2014 08:42 pm
  PM Quote Reply
9th Post
tallyhoe
Member
 

Joined: 08-17-2014
Location:  
Posts: 29
Status: 
Offline
Thanks. I am planning a compression test and oil fog if needed to start zeroing on issue. Later part (19 years) of it's life before me was woman owned as a toy, so I suspect maintenance was an afterthought. It shall be interesting.

Back To Top PM Quote Reply  

 Posted: 08-20-2014 07:59 am
  PM Quote Reply
10th Post
subwoofer
Member
 

Joined: 04-01-2008
Location: Sandefjord, Norway
Posts: 617
Status: 
Offline
Mods: This thread should be moved to the appropriate forum?

Paul Koehler wrote:
Beg,borrow, buy or steal Des Hammond's book on Dellorto's & Weber carbs; read it  3 or 4 times or enough times until it starts to sink in and then have at it with your Webers.

That book is highly overrated. I have it, and in terms of actually explaining how carb circuitry works it contains next to nothing. But good for rebuild instructions, I'll give it that.

--
Joachim

Back To Top PM Quote Reply

 Posted: 08-20-2014 12:48 pm
  PM Quote Reply
11th Post
tallyhoe
Member
 

Joined: 08-17-2014
Location:  
Posts: 29
Status: 
Offline
I am sure a carb rebuild is in my future so it may be a good purchase.
Thanks

Back To Top PM Quote Reply  

 Posted: 08-21-2014 04:28 pm
  PM Quote Reply
12th Post
Mitch Ware
Member


Joined: 03-12-2005
Location: Albany, New York USA
Posts: 204
Status: 
Offline
I converted my car to SU's. Almost a strait bolt on swap. the float bowl on the front carb hits the alternator though. So I had to put a longer belt on and swing the alternator to a lower position. Also, I had to very carefully grind away part of the float bowl to clear.

Other than that an easy swap.

Mitch Ware
#19670
#11002

Back To Top PM Quote Reply

 Posted: 08-22-2014 12:02 am
  PM Quote Reply
13th Post
tallyhoe
Member
 

Joined: 08-17-2014
Location:  
Posts: 29
Status: 
Offline
Something to think about. HS2?

Back To Top PM Quote Reply  

 Posted: 08-22-2014 12:36 am
  PM Quote Reply
14th Post
Esprit2
Member
 

Joined: 05-01-2005
Location: Minneapolis, Minnesota USA
Posts: 575
Status: 
Offline
tallyhoe wrote:
Thanks again. USA. Minnesota.Where in Minnesota. I'm in Wayzata... west suburb of Minneapolis.

Last edited on 08-22-2014 03:03 am by Esprit2

Back To Top PM Quote Reply

 Posted: 08-22-2014 12:42 am
  PM Quote Reply
15th Post
tallyhoe
Member
 

Joined: 08-17-2014
Location:  
Posts: 29
Status: 
Offline
Plymouth. Neighbor.

Back To Top PM Quote Reply  

 Posted: 08-22-2014 03:52 am
  PM Quote Reply
16th Post
Esprit2
Member
 

Joined: 05-01-2005
Location: Minneapolis, Minnesota USA
Posts: 575
Status: 
Offline
First, do you know when the timing belt was last replaced? If not, replace it now before putting the car into general service. The belt is supposed to be replaced every 24k miles or 24 months (whichever comes first), and time is just as important as mileage.

If you'd like to get together sometime, I'll take a look at it. No promises, just another opinion. We can make certain the cam and ignition timing are right, then dig into the carbs a bit.

Which Webers? Including the dash number after the throat size... like DCOE40-151.

The problem with Webers is that neither J-H nor Lotus ever used them on their stock versions of the 907... both used Dellorto DHLAs instead. So with Webers, you don't have that history of factory settings to use as a starting point, and you're pretty much starting from scratch.

What jetting is in the carbs now? Matt Cooper at Eurocarb Ltd in the UK knows both Weber and Dellorto carbs, and he also knows the Lotus 907/ 911/ 912 engines very well. Perhaps he could comment on the current jetting. I'm a Dellorto guy, and could offer some more specific input on DHLA/ 907 set-up, but Weber jetting would be more of an exploration.

In the chart below, the first two columns are generic jetting set-ups by the standard Weber jetting formulas. The third column is what Charlie S. used in the otherwise stock 907 in his Lotus Eclat. Pete B's Yelodog is 2.2 liters, 11.1:1 compression, big cam, ported, 0.180 oversize valves... etc, etc... so probably not a good match for yours.

.......................................................... Charlie ..... Pete's
Weber Jetting: .. Power ..... Economy ... Seabrook .. YELODOG
Carb Size ....... 45DCOE9 .. 45DCOE9 .. 45DCOE9 .. 45DCOE9
Choke (mm) ...... 36 ............ 36 ............ 35 ............ 36
Main Jet ........... 135 .......... 135 ........... 120 ........... 135
Air Corrector .... 160 .......... 175 ........... 180 ........... 180
Emulsion Tube .. F16 ............ F9 ............. F2 ............ F3
Idle Jet .............. 55 ............ 50 ............ 50 ............ 50 (50F9)
Idle Air Bleed ..... F9 ............ F9 ............. F9 ............ F9
Pump Jet ........... 40 ............ 40 ............. 50 ............ 45

Charlie’s comments:
"If gas mileage is really important, the 45F8 idle jet can be used. Idle jets on Webers control the mixture from idle all the way up to and beyond 4000 RPM. With this jet, you get some slight lean surge and a definite hesitation when opening the throttle at 3000-3500 RPM. The 45F8 saved me about 2 MPG on long trips over the 50F9. If you want better off-idle response, use 55F8 idle jets. Again, you will lose another mile or two per gallon."

IMHO, Charlie’s set-up is rather conservative and biased more for economy that performance.

Pete posts here. Perhaps he will chime in.

Regardless, knowing what jetting is in your carbs now would be a good place to start. Open them up.

Dyno-Tech (Tim Moore, or it could be his son by now) off I-94 in the Hwy 280/ Cretin-Vandallia area knows Webers and could tune your engine on a chassis dyno.

DynoTech Automotive (Tim Moore)
(612) 379-4205
2090 Gilbert Ave, St. Paul, MN 55104
Dynomometer tune-ups - Power or Emissions
https://www.facebook.com/pages/Dynotech-Auto/138837712830146

Last edited on 08-22-2014 04:39 am by Esprit2

Back To Top PM Quote Reply

 Posted: 08-22-2014 04:36 am
  PM Quote Reply
17th Post
Esprit2
Member
 

Joined: 05-01-2005
Location: Minneapolis, Minnesota USA
Posts: 575
Status: 
Offline
tallyhoe wrote:
I am a new owner of a JH so please be patient. I am looking for direction on the what is the best process to check out the condition of the units. (Snip)...How long have you had the J-H, and did any service history come with the car? Not to beat on it too hard, but do you know when the timing belt was last changed? If you don't know, or if it has been more than 24 months, then make replacing the timing belt job #11. The 907 is not a clearance engine. That means that if the belt breaks or jumps timing, the pistons will wipe out the valves. You don't have to be paranoid about it, but do be smart.

What year is the car? What's the engine number? It's stamped on the top of the block's rear flange, above the starter. Peer down between the firewall and the rear carb.

Do you have the Workshop and Parts manuals? If you don't, get them.

Weber DCOE carbs look like Dellorto DHLAs, and the factory used Dellortos. Are you sure they're Webers?

Last edited on 08-22-2014 04:37 am by Esprit2

Back To Top PM Quote Reply  

 Posted: 08-22-2014 01:03 pm
  PM Quote Reply
18th Post
tallyhoe
Member
 

Joined: 08-17-2014
Location:  
Posts: 29
Status: 
Offline
I have no info on the car. Last titled in 09. 48K. I assume nothing is right, or good, or replaced on time. It runs, barely at idle. Compression 120, 75,70, 120. Dies upon pushing the accelerator. New fuel pump was installed to make it kinda run. Bottom end sounds real solid. No funny noises at idle but I can't re it up. I suspect cam timing a problem also. A new belt and carb kit is ordered.

Thanks again everybody.

Back To Top PM Quote Reply

 Posted: 08-25-2014 01:55 pm
  PM Quote Reply
19th Post
Mitch Ware
Member


Joined: 03-12-2005
Location: Albany, New York USA
Posts: 204
Status: 
Offline
tallyhoe wrote: Something to think about. HS2?

HS6

Mitch Ware
#19670
#11002

Back To Top PM Quote Reply  

 Posted: 09-01-2014 06:43 pm
  PM Quote Reply
20th Post
tallyhoe
Member
 

Joined: 08-17-2014
Location:  
Posts: 29
Status: 
Offline
I finally got all my numbers everybody.
Body 13911
Engine B 7308349
Webers 40 DCUOE 2 #66

Cam timing and ignition are good. Fuel pumps and filter are in full flow and floats and needle jets look good and don't leak. Still just kinda idles and dies on acceleration. I will pull distributor next. This car has an oil cooler installed which makes removing the filter an act of God needed to accomplish. Is there a shorter one that works?
I also mis-typed in that it has 68K on it.

Back To Top PM Quote Reply

Current time is 04:05 pm Page:    1  2  Next Page Last Page    
> Jensen Healey & Jensen GT Tech > Carburetors > Webers or ? Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems