Rear window defogger for a hard top option ...   07-21-2005 11:46 am

Frank, you are correct there are no special washers or sealers it's just a male to female fit, personally if it was me I would ...   07-19-2005 02:35 pm

Bruce Madden in Atlanta rebuilds those wiper switch's and all the other ones as well, super guy and does good work, I think his phone ...   07-13-2005 04:53 pm

Hi Tim, I have some pict's but right now they are stuck in the camera and to be honest I dont really know how to ...   07-13-2005 12:02 pm

Jim, on my way to the 2005 Nationals in Philly this past week my car started to smoke after driving about two hours, and the ...   06-27-2005 12:21 pm

Erik, cant help you with the wiring size but I do have a tip, Frank Shwartz from 2004 East coast Nationals fame tipped me to this ...   06-13-2005 05:45 pm

Andrew, not sure about the part numbers but have you considered just getting yours rebuilt, the cost is usually less than $100 and you know ...   06-07-2005 10:38 am

Andrew I'm using 90 W in the 5-speed and have been for years with no problems. Brett. ...   06-03-2005 03:26 pm

Kurt,    Yea I read that about the blow by pipe but I dont have a clue as to what it means, I dont see anything ...   05-31-2005 11:09 am

Ken, on my 75 JH I was told by Jim Medland at Delta to lign up the 110's with each other at TDC and that ...   05-24-2005 04:01 pm

Thanks Guy's I appreciate the input and knowledge you are willing to sharing with me, it seem's my 4 vacuum gauge setup just wont make it ...   05-24-2005 01:52 pm

Help, I’m still having Dellorto troubles and they are turning into nothing but a frustrating money pit that am about to give up on, and ...   05-23-2005 02:08 pm

Kurt, I wasn't sure just what you meant by redrilling your emulsion tubes untill I just recieved the 7850.7 idle jet emulsion tubes from Dave ...   05-19-2005 03:41 pm

Brian, at $300 plus shipping which aint cheap either, I would just hold on to what you have, I'm running a tinted that I had ...   05-18-2005 03:22 pm

Yes they are and it will save you a lot of time mucking about trying and fitting an alternative, get yourself a lot of self ...   05-17-2005 11:37 am

George, yes you are correct taper side fit's into the steering wheel, put a little heavey grease on it to hold it in place, as ...   05-17-2005 11:28 am

Paul, what I use is a pump oil can with a flex neck that you can pick up at most car parts stores, I dont ...   05-17-2005 11:19 am

Thanks for the tip's guy's, I guess I'll be buying some Dellorto parts today, I'll let you know how I make out once they arrive. Brett. ...   05-13-2005 03:50 pm

Yes Tim, I'll be there, ( if I can get these #%*^@+# Dellorto's sorted out ) I'm hooking up with Jeff and Laura Peterson from ...   05-12-2005 04:48 pm

Tim, you recieved a good bunch of suggestions but if they dont work for you might want to try looking at fuse connections, I've been ...   05-12-2005 01:41 pm

if you have a 5 speed it could also be a shifter bushing issue. Brett. ...   05-06-2005 04:10 pm

Erik, while you have your pedal box off have a look at the weld points were the pedal arms attach to the pivoting rod, I ...   04-28-2005 05:27 pm

Thanks for the info, I think I will try and pick up one of those JH oil tanks that go on the firewall but in ...   04-22-2005 02:51 pm

Paul Delta has a replacement it's not the same but it will work for you, as for what goes wrong with them as long as ...   04-22-2005 12:26 pm

Jim, you dont say if your loosing oil or anti freeze, but lets say your oil is OK and coolant is the culprit because the ...   04-22-2005 12:15 pm

Hello all, I'm looking for some advice from the "been there done that" group who have installed Dellorto's, I am presently in the install mode ...   04-21-2005 11:59 am

Hey Thanks Mark great tip, I have been suffering the same problems and tried every thing, smoothing off the linkage, extra return spring, etc. etc. ...   04-19-2005 11:20 am

Synd, I dont have a pict, handy but all it is is a piece of angle bracket 90 degrees      1-1/2" to 2" wide with a ...   04-18-2005 10:25 am

George, rebuilding the shifter is rather easy, if you have the schematic of what it looks like (If you dont I have one I can ...   04-12-2005 12:25 pm

Dan, you should be talking with Mitch Ware he did what you are doing now plus he owns a body shop and could probably give ...   04-11-2005 03:06 pm

Oopps I forgot Delta or Club store will have all the parts. ...   04-11-2005 01:18 pm

Daryl. I'ts not to bad a job just get your car safely and securely up in the air, loosen the clamping bolt at the upper and ...   04-11-2005 01:17 pm

Alot of the nuts / bolts and screws can be salvaged just by sandblasting, I got a piece of card board and stuck screws and bolts ...   04-11-2005 01:06 pm

Rory you recieved a lot of very good tips here to follow up on, the one statement you made about sanding your mixture needles though ...   04-05-2005 11:15 am

I found this stuff listed at Global Performance Parts in Michigan http://WWW.GLOBALPERFORMANCEPARTS.COM I plugged in the P/N#'s  and they all came up, check it out but let ...   04-04-2005 05:49 pm

Rory, sounds like it's running lean, try with the air cleaner off raising the barrel in the carb about 1/8"  quickly to see if the speed ...   04-04-2005 05:39 pm

Thanks for the replies guys I think I'll go that root and feed them from the back. Cheers   Brett. ...   03-30-2005 11:23 am

Hello all I just picked up some Dell's for my little toy and while I dont have them in front of me right now, I've been ...   03-29-2005 04:30 pm