| ||||
|
Posts by Brett Gibson JH5 20497 | |
---|---|
798 posts | Showing posts 201-240 of 798 |
Projects > GT almost ready (21 replies - 37666 views) Very Nice ... 03-17-2015 12:53 pm Cooling > fan clutch (18 replies - 29298 views) It's true the clutch fans came on JH5's & GT's and they work great in cooling the engine, that is until the clutch freeze's up, ... 03-17-2015 12:52 pm Ignition > Static Timing Questions (11 replies - 20504 views) Sounds like the distributor has pop out of it's drive, there is one nut on a stud from the block that holds the dizzy clamp ... 01-19-2015 01:14 pm Miscellaneous > East Coast Nationals 2015 (3 replies - 7921 views) Bump ... 01-14-2015 01:06 pm Suspension > Front suspension (53 replies - 90851 views) That's were they go if the mount was not their then the bar would be metal on metal, and actually the exhaust pipe is usually ... 01-07-2015 07:11 pm Carburetors > Sluggish acceleration (9 replies - 18243 views) I'm thinking you need to start at the beginning and make sure that your ignition, timing, plugs, wires, compression etc are all correct before you ... 01-05-2015 12:55 pm Suspension > Delta Motorsports Rear Springs (7 replies - 14339 views) I just went and checked the rear springs on my restoration JH in the garage and they are the thicker version and rounded at both ... 12-31-2014 02:54 pm Carburetors > Sluggish acceleration (9 replies - 18243 views) Pop the dizzy cap and look for dampness, with all the rain maybe some dampness/condensation got in and your not getting a good spark to ... 12-29-2014 01:03 pm Projects > New Restoration Project Started - 13046 - Riverside, CA (70 replies - 102188 views) Block off one side, put a gauge and air fitting on the other, put a bit of air pressure in it and see if ... 12-02-2014 01:07 pm Suspension > Fitting rear Superpro bushes (27 replies - 50660 views) yes the uppers are just a smaller version. ... 11-26-2014 12:52 pm Suspension > Fitting rear Superpro bushes (27 replies - 50660 views) Eric, your correct the original bushings came with an outer metal ring that the "rubber" bushing was molded to and the whole thing was pressed ... 11-25-2014 01:04 pm VIN Database for Jensen Healey & Jensen GT > Jensen Healey & Jensen GT VIN Database (342 replies - 541962 views) a place to look for the vin is on the drivers side frame rail in the engine bay, about mid way towards the front. they ... 11-20-2014 01:49 pm Projects > New Member - Just getting started (2 replies - 7970 views) Buy a decent wire feed welder and a very good 4-1/2" angle grinder, start welding and if it doesn't look good grind it down and ... 11-16-2014 02:19 pm Fuel Stuff > Fuel Tank Drain Plug (2 replies - 8378 views) You stand a bigger chance of corrosion with aluminum than brass, and if I remember correctly it's a pipe thread NPTE not sure of the ... 11-15-2014 01:20 pm Electrical & Instruments > Fuel Pump Wiring (11 replies - 18675 views) Don't forget that they also put wires in the trunk for the hard top defroster. ... 10-30-2014 12:42 pm Wheels > Pad in Differential (13 replies - 25125 views) yes 75-90 gear oil in the rear end, some people use it in the transmission as well, me for one (4 or 5 speed), then ... 10-06-2014 05:17 pm Wheels > Pad in Differential (13 replies - 25125 views) Rear end 90 gear oil. engine 20-50 ... 10-06-2014 01:26 pm Electrical & Instruments > Interesting Dashboard Traits Delivered by Lucas (3 replies - 8689 views) The JH alternator has a hard time of it if you run most of the stuff at once so seeing fade is probably correct, as ... 10-01-2014 01:02 pm Engine & Transmission > oil pan (11 replies - 19093 views) I am starting to thing you have an early version engine and are disconnecting the oil return from the catch bottle on the firewall to ... 09-28-2014 01:59 pm Engine & Transmission > oil pan (11 replies - 19093 views) there is a drian plug on the back side of the pan.
... 09-27-2014 01:13 pm Fuel Stuff > Custom Tank-No Breather/Pressure Relief (4 replies - 11175 views) No breather means no venting, so if you pump out gas it creates a vacumn and after awhile the vacumn gets so great you dont ... 09-20-2014 01:03 pm Electrical & Instruments > Wiring Harness Installation (6 replies - 13661 views) Now that is funny, I had the same issue but luckly I have another JH and was able to go to that and check the ... 09-19-2014 01:03 pm Body & interior stuff > Door panels Fit (2 replies - 7021 views) The door panels do in deed go up against the interior door seals, I can send a photo but wont be till next week.
PM me ... 09-10-2014 12:56 pm Body & interior stuff > Exterior Mirror Mounting (9 replies - 18941 views) the rubber seal around the glass allows you to replace the glass, you can also take the glass out and adjust the tension on the ... 08-31-2014 02:27 pm Ignition > No start... (4 replies - 9900 views) I think you need to find out if the starter is actually turning the engine over, hopefully it is just a starter issue. ... 08-31-2014 02:22 pm Body & interior stuff > Exterior Mirror Mounting (9 replies - 18941 views) It's a standard English unit used on a number of differant cars, googling might bring it up, but I do have some info on it ... 08-27-2014 01:04 pm Cooling > GT water pump? (3 replies - 9775 views) True, differant, Bruce Madden in GA rebuilds them.
... 08-16-2014 12:56 pm Ignition > Ignition sprocket timing mark (4 replies - 11385 views) The cam pulleys and crank need to be lined up, as for the dizzy you want the rotor pointing at the #1 spark plug lead ... 08-11-2014 12:47 pm Engine & Transmission > Transmission moving? (8 replies - 13263 views) It's not supposed to move alot so time to check the trans mount's and also the engine mounts. Rev the engine and watch it to ... 07-18-2014 12:58 pm Projects > The Red Fox (15 replies - 27057 views) Kurt seeing you have the glass out I would recommend sticking a bit of sound deading material on the inside of the outer door skin.
... 07-02-2014 12:57 pm Body & interior stuff > Interior trim (10 replies - 16430 views) If your just patching a worn seat section keep in mind the rear bulk head has the correct material on it, so if you use ... 06-27-2014 12:47 pm Projects > 18711 "Miss Jensen" (129 replies - 247063 views) Joachim, what we do for a vehicle inspection here in New York State is a joke compared to what you go thru...
Brett
... 06-18-2014 12:14 pm Body & interior stuff > Chassis Number (3 replies - 7954 views) Plus I found another, a small metal plate welded to the the front seat rail support on the drives side US.
... 06-02-2014 02:04 pm Projects > 16173 will be entering project status... (162 replies - 259319 views) Cant wait to see it at the WI show.
... 05-13-2014 12:53 pm Ignition > HELP! Serious running issues! (7 replies - 15118 views) Glad to hear your back up and running, yes you are probably right gas drying out gets thicker and sticky best thing you can do ... 05-06-2014 01:11 pm Ignition > HELP! Serious running issues! (7 replies - 15118 views) Have to agree with Joachim, it's in your carb's.
... 05-05-2014 12:52 pm Engine & Transmission > Worn Cam Shaft Timing wheels ? (22 replies - 37088 views) Usaully to tight a belt is the culprit.
... 04-27-2014 04:34 pm Engine & Transmission > Worn Cam Shaft Timing wheels ? (22 replies - 37088 views) If they are shinny on the surface and have a bit of a lip on the tooth one edge or the other they are worn. ... 04-27-2014 01:46 pm Miscellaneous > Jensen East 2014 (15 replies - 23543 views) Just a heads Up, I was talking with Ron Mau yesterday (He's putting on the show) and the block of rooms that are being held ... 04-22-2014 01:27 pm Body & interior stuff > Hood latch (Bonnet latch) (3 replies - 9412 views) Are you sure it is just not the spring loaded clip that the rod goes into is not sticking open, what does the hieght of ... 04-17-2014 02:11 pm | |
Current time is 06:26 am | 1 2 3 4 5 6 7 8 9 10 11 ... |