Home 
Home Search search Menu menu Not logged in - Login | Register
> Brett Gibson JH5 20497

Profile Topics Posts
Posts by Brett Gibson JH5 20497
734 postsShowing posts 121-160 of 734

Projects > 16173 will be entering project status... (162 replies - 101257 views)

Mike, I believe at the show you mentioned that you have never rebuilt the carb's, so whats crossing my mind is if you have the ...   07-15-2015 12:55 pm

Projects > 16173 will be entering project status... (162 replies - 101257 views)

Mike. loose the points go with electronics, also dont forget to put a full face gasket on both bypass valves on the carb's. You also ...   07-11-2015 01:18 pm

Ignition > John Kimbrough's web page (1 reply - 2163 views)

https://sites.google.com/site/johnsjensenhealeywebpage/ Try this Frank. ...   07-07-2015 01:47 pm

Intro Tech Board stuff > Jensen Healey Restoration in NY (4 replies - 3446 views)

Were in NY ...   05-29-2015 12:36 pm

Engine & Transmission > sticking clutch after long storage (7 replies - 4073 views)

There are a couple of ways to un-stick a stuck clucth, one is take the thing apart, the other jack the car up with the ...   04-27-2015 12:48 pm

Miscellaneous > Jenesen Travels (9 replies - 5212 views)

Great to meet up with you Kurt and put a face to the post's, and taking the time to share one of your breakfast place's ...   04-25-2015 12:21 am

Miscellaneous > Jenesen Travels (9 replies - 5212 views)

Kurt, after JHPS we travel up Hwy 1 for a couple of days and end up in San Fran for Friday eve, we might even ...   04-20-2015 01:29 pm

Miscellaneous > Jenesen Travels (9 replies - 5212 views)

We are Kingman AZ right now so we are getting closer to meeting up with the JHPS Group. Even went to the car wash to ...   04-20-2015 04:53 am

Engine & Transmission > Cam belt tensioner bolt stripped (4 replies - 2672 views)

I have not had this experience but seeing you have had no input on your problem the way I would go would be a heli-coil, ...   04-20-2015 04:50 am

Miscellaneous > Jenesen Travels (9 replies - 5212 views)

The four Healey's travelling Route 66 to California plan on attending the monthly JHPS meeting and hopefully meeting as many of our West Coast brethren ...   04-16-2015 01:09 pm

Miscellaneous > Jenesen Travels (9 replies - 5212 views)

FYI Four Jensen Healey's one from NY, Illinois Tennessee & Iowa all headed of along route 66 headed for California and are doing it now ...   04-12-2015 01:50 am

Engine & Transmission > 5 speed longevity (20 replies - 10204 views)

Bfitz241, received your private message correcting my spelling, I assume there was no offence intended. Thanks so much. Brett ...   03-26-2015 01:01 pm

Engine & Transmission > 5 speed longevity (20 replies - 10204 views)

4 speed wont fit a 5 speed bellhousing, drive shafts are different as well. Clutch the same. ...   03-25-2015 06:43 pm

Engine & Transmission > 5 speed longevity (20 replies - 10204 views)

You are talking getting parts verse's how the transmission holds up, true the parts are getting few and far between but this transmission can take ...   03-25-2015 06:43 pm

Engine & Transmission > 5 speed longevity (20 replies - 10204 views)

Well I guess no one told me they were not a very good transmission, other than rebuilding the shifter mine has behaved well for over ...   03-24-2015 12:52 pm

Miscellaneous > British Nationals Meet May 28-29-30 (0 replies - 1653 views)

Got word from Barret Harrison ( barrett10@sbcglobal.net ) that this show is looking for a very nice Jensen Healey to feature in the Crown Jewels ...   03-20-2015 06:10 pm

Projects > GT almost ready (21 replies - 11793 views)

Very Nice ...   03-17-2015 12:53 pm

Cooling > fan clutch (18 replies - 9632 views)

It's true the clutch fans came on JH5's & GT's and they work great in cooling the engine, that is until the clutch freeze's up, ...   03-17-2015 12:52 pm

Ignition > Static Timing Questions (9 replies - 5962 views)

Sounds like the distributor has pop out of it's drive, there is one nut on a stud from the block that holds the dizzy clamp ...   01-19-2015 01:14 pm

Miscellaneous > East Coast Nationals 2015 (3 replies - 3206 views)

Bump ...   01-14-2015 01:06 pm

Suspension > Front suspension (45 replies - 41562 views)

That's were they go if the mount was not their then the bar would be metal on metal, and actually the exhaust pipe is usually ...   01-07-2015 07:11 pm

Carburetors > Sluggish acceleration (9 replies - 6604 views)

I'm thinking you need to start at the beginning and make sure that your ignition, timing, plugs, wires, compression etc are all correct before you ...   01-05-2015 12:55 pm

Suspension > Delta Motorsports Rear Springs (7 replies - 4574 views)

I just went and checked the rear springs on my restoration JH in the garage and they are the thicker version and rounded at both ...   12-31-2014 02:54 pm

Carburetors > Sluggish acceleration (9 replies - 6604 views)

Pop the dizzy cap and look for dampness, with all the rain maybe some dampness/condensation got in and your not getting a good spark to ...   12-29-2014 01:03 pm

Projects > New Restoration Project Started - 13046 - Riverside, CA (70 replies - 33695 views)

Block off one side, put a gauge and air fitting on the other, put a bit of air pressure in it and see if ...   12-02-2014 01:07 pm

Suspension > Fitting rear Superpro bushes (27 replies - 18518 views)

yes the uppers are just a smaller version. ...   11-26-2014 12:52 pm

Suspension > Fitting rear Superpro bushes (27 replies - 18518 views)

Eric, your correct the original bushings came with an outer metal ring that the "rubber" bushing was molded to and the whole thing was pressed ...   11-25-2014 01:04 pm

VIN Database for Jensen Healey & Jensen GT > Jensen Healey & Jensen GT VIN Database (278 replies - 242391 views)

a place to look for the vin is on the drivers side frame rail in the engine bay, about mid way towards the front. they ...   11-20-2014 01:49 pm

Projects > New Member - Just getting started (2 replies - 2604 views)

Buy a decent wire feed welder and a very good 4-1/2" angle grinder, start welding and if it doesn't look good grind it down and ...   11-16-2014 02:19 pm

Fuel Stuff > Fuel Tank Drain Plug (2 replies - 3167 views)

You stand a bigger chance of corrosion with aluminum than brass, and if I remember correctly it's a pipe thread NPTE not sure of the ...   11-15-2014 01:20 pm

Electrical & Instruments > Fuel Pump Wiring (11 replies - 7664 views)

Don't forget that they also put wires in the trunk for the hard top defroster. ...   10-30-2014 12:42 pm

Wheels > Pad in Differential (13 replies - 10482 views)

yes 75-90 gear oil in the rear end, some people use it in the transmission as well, me for one (4 or 5 speed), then ...   10-06-2014 05:17 pm

Wheels > Pad in Differential (13 replies - 10482 views)

Rear end 90 gear oil. engine 20-50 ...   10-06-2014 01:26 pm

Electrical & Instruments > Interesting Dashboard Traits Delivered by Lucas (3 replies - 3352 views)

The JH alternator has a hard time of it if you run most of the stuff at once so seeing fade is probably correct, as ...   10-01-2014 01:02 pm

Engine & Transmission > oil pan (11 replies - 6991 views)

I am starting to thing you have an early version engine and are disconnecting the oil return from the catch bottle on the firewall to ...   09-28-2014 01:59 pm

Engine & Transmission > oil pan (11 replies - 6991 views)

there is a drian plug on the back side of the pan.   ...   09-27-2014 01:13 pm

Fuel Stuff > Custom Tank-No Breather/Pressure Relief (4 replies - 4232 views)

No breather means no venting, so if you pump out gas it creates a vacumn and after awhile the vacumn gets so great you dont ...   09-20-2014 01:03 pm

Electrical & Instruments > Wiring Harness Installation (6 replies - 4755 views)

Now that is funny, I had the same issue but luckly I have another JH and was able to go to that and check the ...   09-19-2014 01:03 pm

Body & interior stuff > Door panels Fit (2 replies - 2744 views)

The door panels do in deed go up against the interior door seals, I can send a photo but wont be till next week. PM me ...   09-10-2014 12:56 pm

Body & interior stuff > Exterior Mirror Mounting (9 replies - 6713 views)

the rubber seal around the glass allows you to replace the glass, you can also take the glass out and adjust the tension on the ...   08-31-2014 02:27 pm


 Current time is 11:20 pm
 First Page Previous Page  1  2  3  4  5  6  7  8  9  ...  Next Page Last Page


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems