The bar is a bit low but so is every thing else, spoiler / exhaust / rear bar, and most flat tires happen slowly were ...   07-25-2008 10:37 am

Are all our car doing so well that there has'nt been a post since the 19th, or is there an issue with it. ???. I ...   07-24-2008 10:23 am

Judson, at the last couple of Nationals here in the East I have been checking belt tension with this gauge from Mcmaster Carr on a ...   07-01-2008 03:59 pm

I think I posted this once before, but just to be sure I'l do it again. A perfect match substitute for the Square cut oil hose ...   06-26-2008 11:04 am

The numbers I was given and believe Greg recommends are, Choke 33, Main jet 145, MJ emulsion tube 7772.5, MJ air correction jet 190, Idle jet ...   06-24-2008 11:28 am

Not sure about your car Lash, but I have another 3 fuses in the area of the coil on the fire wall, maybe it's a ...   06-23-2008 03:03 pm

New Info......... Jensen Friends, Here’s an update of planned activities for this year’s meeting of the Jensen faithful.   Thursday:  AM         Caravan to Corning Museum of Glass  We anticipate a ...   06-10-2008 05:02 pm

You got it, if memory serves, those two hoses go into the heater box above the core, and are not subject to it, the fan ...   05-29-2008 02:27 pm

The lever operates a flap inside the heater box, and also engages a small vac control valve, which allows vacuum to the water flow valve, turning ...   05-28-2008 10:21 am

no, thats the only valve there is, with out it the water flows thru the heater core. ...   05-27-2008 10:19 am

Greg, OK of the top of my head. 1. heater hose, intake manifold to heater core. 2. crank vent, to carb air cleaners 3. get rid of the manifold ...   05-19-2008 01:44 pm

Pull the chrome cover out of the rubber, then you can just remove the lens, bulb is underneath, if it's corroded in try using a ...   05-13-2008 01:24 pm

Ditto, one of the nastiest jobs on the whole dang car, drivers side upper pivot bolt for the suspension was rusted solid, regular beatings / ...   05-08-2008 05:16 pm

Judson, what would be the benefit or would there be to just sticking the green dot sprockets on a completly stock engine, and would the ...   05-06-2008 03:51 pm

you have to have someone crawl under the dash, no way around it, take it to a garage or hire a hooker, course I'd love ...   05-06-2008 01:22 pm

Frank, I tried a colortune once, and was not impressed with the results, I tried full rich to the leanest and it barely showed a ...   05-06-2008 10:17 am

Frank, best way of telling if it's to rich is look at the spark plugs, plus if it backfires after you shut the engine down, ...   05-05-2008 11:32 am

Synthetic 75-90 works well in my 5 speed box. ...   04-30-2008 03:30 pm

Mark, a compression test will tell you if you need to pull the head.  Factory valve clearance cold is exhaust 10 to 12, inlet 5 ...   04-23-2008 10:48 am

#1, Heat the studs, be very carefull to stay away from the block, #2, if its stuck closed, dont bother with it, you dont need ...   04-22-2008 04:30 pm

Do a cylinder pressure test for starters, remember to have the carbs wide open when you do it, that will tell you if your engine ...   04-22-2008 11:55 am

Jeremy, best thing you can do to help yourself is by the Des Hammill book on how to rebuild these puppies, Amazon sell's them cheap. Brett ...   04-22-2008 11:50 am

Tim, how are you, I dont know much as to the SS units, I see UK cars sometimes come up with them installed, plus the ...   04-21-2008 03:32 pm

Just a heads up, Seneca lodge has regular hotel rooms, of which 40 were reserved for the show in June, and then they have cabin's, ...   04-02-2008 12:30 pm

Bill, my car came to me with a Monza system, basically header was 4 into 2, 2 into muffler, 2 out into 2 resonator, and ...   03-25-2008 10:59 am

My thoughts would be that it is something that would require the entire dash being out, hopefully not the windshield as well, one of those ...   03-24-2008 02:41 pm

Bump ...   03-24-2008 10:44 am

Sounds like the carbs are gumming up, especialy the front one to me, try spray carb cleaner as a quickie, but I think your best ...   03-24-2008 10:44 am

It's been done a few times, last pict of one I saw was for a JH on E-bay in England, I dont have any pict's ...   03-24-2008 10:40 am

If memory serves me correctly, Bruce Madden in Atlanta will take your old one and repair it, he also fix's the original rocker switch's as ...   03-19-2008 03:54 pm

Joel, give me your e-mail and i'l shoot 6 picts over, not sure how to post them here. nothing seems to work, probably to big ...   03-18-2008 06:03 pm

George, first thing to realize with attaching the spoiler Delta supplies, is that you just don't bolt it up the way it came, if you ...   03-18-2008 03:01 pm

As "Arnold" would say "what are you guy's Girly Men", heck Greg it ain't a game if you don't have casualties. But rest assured there will ...   02-01-2008 03:35 pm

Man I'm sorry to hear people having trouble with these new tanks, you would think for that kind of money the bugs would be worked ...   01-25-2008 02:58 pm

Man I'm sorry to hear people having trouble with these new tanks, you would think for that kind of money the bugs would be worked ...   01-25-2008 02:58 pm

Well the Web site is up and running and I'm passing along the info I was given, If you have not been to one of ...   01-17-2008 01:24 pm

I think you should start by looking at a repair manual / parts manual and owners manual. Once you have that down go to the ...   01-08-2008 11:00 am

There is no inside cover, they are held on by long stud's with spacer's that keep it from rubbing the belt, you might have to ...   12-10-2007 11:28 am

Arvin, I stuck one in the mail to you Saturday. ...   12-03-2007 01:20 pm

Seem's like the crankshaft pulley is the issue here, why not get a GT or JH5 crank pulley and use that, no way are they ...   11-21-2007 01:28 pm