| ||||
|
Posts by Brett Gibson JH5 20497 | |
---|---|
798 posts | Showing posts 401-440 of 798 |
Engine & Transmission > Intake valve clearance (3 replies - 8186 views) As your engine heats up things expand which reduces clearances, there is a possibility that you might not have a valve completely seated, then again ... 05-17-2011 12:59 pm Engine & Transmission > Getrag Synchros (1 reply - 5665 views) Lash, Mitch Ware posted some info on synchro's when he had his rebuilt, I can only find this bit, but if you contact him he ... 05-10-2011 07:32 pm Miscellaneous > Jensen 2011 Eastcoast Nationals At Lake Placid (10 replies - 19881 views) Well, dusted the JH off yesterday and went for a quick spin, man it felt good to be behind the wheel again.
Looking forward to this ... 05-01-2011 01:56 pm Carburetors > Webers pouring gas onto starter (9 replies - 15540 views) Nels, just a tip with the JH electric's, make sure you have good grounds I've seen alot of issue's that were caused by that.
Brett
... 04-25-2011 06:32 pm Electrical & Instruments > Hazard Rocker Switch (9 replies - 11198 views) $70 bucks for a $3 switch man thats crazy, I sure hope with parts going for this kind of dow it drives up the value ... 04-22-2011 01:20 pm Carburetors > revving issues (17 replies - 25242 views) I get the feeling your trying to drive a car that is not really ready to be driven, you should take a time out and ... 04-21-2011 07:34 pm Body & interior stuff > Soft top up and down (7 replies - 14558 views) Bruce, I'm one of the lay it on the trunk, tuck the side flaps in and roll it up, some people lay a towel over ... 04-21-2011 01:24 pm Carburetors > revving issues (17 replies - 25242 views) Sounds like someone plumbed the carbs to pull in the engine and valve cover oil vapors, usally most poeple would just tap the back of ... 04-21-2011 01:15 pm Body & interior stuff > dashboard wood removal (15 replies - 27717 views) Ross, when you pull the choke cable off the carbs just to make it easier to get back in without taking to much of the ... 04-14-2011 01:07 pm Electrical & Instruments > Replacement Switches for Panel lights and Hazard (4 replies - 11360 views) there are switch's out there that can replace the JH switch's and have the same look, most are Brit car sites that have them. here's ... 04-14-2011 12:58 pm Ignition > vacum lins (1 reply - 6363 views) If you dont have a diagram on what should run were, go to the Delta Motor Sport site they sell JH parts by using the ... 04-06-2011 01:22 pm Engine & Transmission > runs very bad when engine (3 replies - 6953 views) sounds like you need get the timing set, go thru the ignition and making sure what you have is good and in working order, plugs, ... 04-06-2011 01:19 pm Carburetors > Dellorto DHLA 45 (5 replies - 11960 views) Eurocarb LTD. at this site should have another cover for you but I think when I checked it was pretty $$$ thats why I thought ... 03-27-2011 02:14 pm Engine & Transmission > 5 spd Shifter removal help needed (3 replies - 8430 views) Pete,
Yes the shifter can be removed with out much trouble at all, I don’t have the
diagram in front of me but if memory ... 03-21-2011 01:24 pm Engine & Transmission > 5 Speed Transmission (3 replies - 7845 views) Lash, Mitch Ware posted a while back with the part numbers for the 5 speed syncro's he had his rebuilt, if he doesn't respond to ... 03-20-2011 02:16 pm Miscellaneous > Jensen 2011 Eastcoast Nationals At Lake Placid (10 replies - 19881 views) Bump ... 03-03-2011 01:01 pm Body & interior stuff > Tow Eye (3 replies - 8026 views) The front cross member has a plate attached with a whole in it on the bottom side that should do the trick, unless your running ... 03-02-2011 01:08 pm Engine & Transmission > 1 piece driveshaft on 5 speed (3 replies - 9371 views) I think Pete nailed it, sounds like they didnt balance it correctly.
Brett
... 02-21-2011 12:57 pm Engine & Transmission > IT BACKFIRES & DIES!! WHAT'S WRONG? (1 reply - 5950 views) Rob, check your basic timing first and make sure it's were it is supposed to be, cam's aligned, at TDC, firing on #1, then look ... 02-19-2011 08:47 pm Engine & Transmission > 2 piece propshaft supprt bearing (1 reply - 5774 views) Dont bother with the two piece drive shaft that center bearing is expensive even if you could find one just replace it with a one ... 02-14-2011 12:55 pm Ignition > lucas distributor 41584 (2 replies - 8842 views) I'd have to look at a spare dizzy to picture what your saying but what comes to mind would be the location of the centrifical ... 02-06-2011 07:05 pm Body & interior stuff > Stone Guards (6 replies - 11901 views) Rob, the area needs to breath, dirt will find away in no matter how hard to try to seal it should it get damp from ... 02-05-2011 02:05 pm Body & interior stuff > Stone Guards (6 replies - 11901 views) Rob
The stone guards were not caulked, they did have a coating of rust proof as with the inner fender, at least on the cars I ... 02-04-2011 05:14 pm Carburetors > Dellorto DHLA 45 (5 replies - 11960 views) Let me know how you make out with getting the casting repaired I did the same thing but was able to drill a tiny hole ... 02-02-2011 02:22 pm Miscellaneous > Jensen 2011 Eastcoast Nationals At Lake Placid (10 replies - 19881 views) Bumpity Bump ... 02-01-2011 01:02 pm Electrical & Instruments > GPS (4 replies - 8915 views) Ditto on the 5 speed ... 01-24-2011 12:59 pm Miscellaneous > Jensen 2011 Eastcoast Nationals At Lake Placid (10 replies - 19881 views) For your information, click on the link for this years Eastcoast Nationals Info. and keep checking back for more updates.
Nice job Lake Placid Team.
http://www.jensen2011.com/index.html
... 01-21-2011 01:13 pm Engine & Transmission > 5 speed shifter (9 replies - 14127 views) Pete's stuff is very well made indeed, he takes his time to do things right.
The real problem was at the factory, who in blue ... 01-18-2011 07:44 pm Ignition > Fuel Injection KIt for 907 (109 replies - 204959 views) Bruce forgot more then you'll ever know about our cars and has helped 100's of us with his knowledge for over 30 years .
I met ... 01-18-2011 01:41 pm Brakes > Mushy brakes (30 replies - 48130 views) Well blast it Pete, wish I had put in silicone when I painted the engine compartment, now I have a few paint / brakefluid bubbles ... 01-18-2011 01:15 pm Engine & Transmission > replacement main bearings (4 replies - 9688 views) Dan, dont forget to use engine oil with ZDDP in it or the new stuff with just eat up that rope seal.
And Good Luck, hope ... 01-14-2011 01:13 pm Body & interior stuff > Has anybody tried a 'SuedeMat' from DashMat? (12 replies - 18977 views) I believe Mitch Ware installed a Delta cap in his car and from what I saw it looked great, you could'nt tell it was'nt original, maybe ... 12-23-2010 03:25 pm Body & interior stuff > Tangerine Orange Paint code needed (1 reply - 8931 views) http://www.jensenhealey.com/forums/view_topic.php?id=1288&forum_id=11
maybe this will help
... 12-14-2010 07:46 pm Engine & Transmission > Understanding the oil pan (14 replies - 23196 views) Dan, I havent done a JH rope seal but have experience with rope seals on pumps. The one main trick was to never cut a ... 12-08-2010 07:53 pm Carburetors > No Start - Smoke (5 replies - 9920 views) you might have gotten something into the carbs that is plugging or reducing the gas flow, do you have a filter on the gas feed line. ... 12-06-2010 01:10 pm Carburetors > No Start - Smoke (5 replies - 9920 views) Not enough info .......
Do a compression test to see if your engine is any good
Align the crank at TDC, do the cam marks line up, ... 12-05-2010 03:18 pm Engine & Transmission > Clutch Fail (7 replies - 11476 views) The pivot is not all that difficult to place back on, just takes a little time, when I reinstalled my trans I knocked it off ... 12-02-2010 05:25 pm Engine & Transmission > Evaporative loss control assembly (6 replies - 9871 views) It's part of a system as a whole has that effect, plus the weight ...... :>) ... 12-01-2010 03:22 pm Engine & Transmission > Evaporative loss control assembly (6 replies - 9871 views) There is a rebuild kit for the carbon cannister inerd's in the Club store for $15.95, but if your housing is shot you would need ... 11-30-2010 07:12 pm Body & interior stuff > STIFF TOP (2 replies - 7086 views) Besides the tip for letting the sun shine on it, all the frame rails should have plastic bushings that the screws go thru with lock ... 11-30-2010 01:18 pm | |
Current time is 06:42 am | ... 6 7 8 9 10 11 12 13 14 15 16 ... |