you need to click on the HOME button just below the JH logo to see all the links. Brett ...   12-21-2011 02:00 pm

Nice job as usual Greg ...   12-09-2011 01:30 pm

Paul, hope you are holding up as best you can, Ellen was a great vibrant bundle of energy and her loss leave's a big hole ...   12-09-2011 01:29 pm

Ross, I would agree with Mason first place to look would be the cable then take a look at the pedal box where the clutch ...   12-08-2011 01:37 pm

Welcome aboard Scott, as for pictures of what goes were the parts cat. is a good source or visit web sites members have put up ...   12-02-2011 01:10 pm

I believe that is nevis blue, check out this web site Greg has a picture of my car in that color or go to the ...   11-19-2011 01:09 pm

The Vega wheels do actually fit a JH, I removed the original JH wheels off a car and put on the steel Vega wheels to ...   11-18-2011 01:53 pm

I think most dealers fabbed brackets and such to fit or just subbed it off to AC shops. Have'nt seen any prints of an AC ...   11-18-2011 01:48 pm

Mitch first off I would check for a good ground between engine and frame, then start checking continuity of the wires alot of the wiring ...   10-25-2011 01:10 pm

Interference fit. ...   10-14-2011 01:31 pm

Nick, latter JH's had the clock on the left of the glove box prior to that they were placed on the right of the steering ...   10-14-2011 01:30 pm

All this talk of lenght got me thinking so I went out to the garage and measured 3 new ones I have on the shelf ...   10-11-2011 01:12 pm

Nick, nice looking car glad that you didn't snuff it without brakes, I gotta ask were you got the failed hoses from maybe you need ...   10-03-2011 01:32 pm

Frank Schwartz might have a spare available, I just helped him strip a couple of cars and one of the items I took off was ...   10-01-2011 02:58 pm

Ross, it is just a vent for the valve covers that at times has a bit of vapor coming out thats why it was hooked ...   09-28-2011 01:16 pm

Ross, the oil filler line is a breather off the the valve covers it should not have a vacumn line going to it. Brett ...   09-27-2011 01:11 pm

Grayhound's pretty cheap on big items. Brett ...   09-14-2011 12:46 pm

Thanks for the photo's Tim I must say it looks very clean and appropriate. The factory probably had it out further than necassary to cover ...   09-14-2011 12:43 pm

can you post a picture of the closer rear bumper sounds like a good option. Brett ...   09-11-2011 01:59 pm

Just pop the shifter assembly off the trans. no need to pull the trans. out, it's a very simple and easy task, take the center ...   09-11-2011 01:57 pm

Mason, you might be able to swap out the badge in the steering wheel with your new one I'm pretty sure the rubber one is ...   08-22-2011 12:42 pm

A new gasket should do the trick without a sealant, but if you reuse the gasket more than once then personnaly I like to use ...   08-10-2011 01:08 pm

I have had a Budge cover for years and just last year a freind gave me a nice quality one, were as the Budge will ...   08-10-2011 01:04 pm

Dont worry about those missing stud's they all came that way just drain the radiator pull the two hose's off the manifold un bolt it ...   08-09-2011 12:57 pm

well now that you have pinned it down to the location of the car :> I would suggest start looking underneath for a nice clean ...   08-06-2011 01:18 pm

Dan, you live in the land of sunshine ...   08-03-2011 01:09 pm

Just to add to my old post about the cat. converter I didnt realize at the time but the drivers side floor pans on cars ...   08-03-2011 01:05 pm

Hey Paul, I have the choke hooked up on my car and it does seem to help it start but it does not stay on ...   08-02-2011 12:29 pm

Frank, Greg has been publishing Marks Stromberg rebuilding in the club magazine "The Standard" for the last few month's, if you dont get it I ...   07-22-2011 01:00 pm

I think from the lack of responce you may gather that this is not something that is common or done very often, I do know ...   07-16-2011 01:28 pm

Center consule's can be switched out easy enough, rope seals your stuck, that said a properly installed one along with the correct oil (ZDDP)?. will ...   07-01-2011 03:07 pm

Randy, early engines use a rope seal for the crank shaft ends verses a true rubber / steal seal on later versions, not sure on the ...   07-01-2011 01:40 pm

Yea the Black JH had the asian Dellorto knock off's, he did a very nice job with that car even took nan award. Brett ...   06-27-2011 01:25 pm

Mitch the later tensioners (single fat ones) use a stud that screws in and out, also NO play. Brett ...   06-14-2011 04:37 pm

Dan, if you have low compression squirt some oil into that cylinder then check agian, if the pressure comes up sure enough bad rings, if ...   06-14-2011 01:03 pm

Mitch, I think I would pop that pulley off and check the seating if that looks Ok best bet would be to replace it. As for ...   06-09-2011 01:10 pm

I's my understanding that the linkage between the carbs has to be disconnected when tuning the carbs, once their in sync then they should act ...   05-31-2011 01:41 pm

No seal there, sounds like your new master cylinder is leaking. Brett ...   05-28-2011 01:14 pm

Welcome to the boards, nice car. I agree with Greg do the bushings and shocks as well as sway bars front and back you wont believe ...   05-24-2011 01:23 pm

Dont use a Buna O-ring you need a gas compatable material, Nitrile is a good choice, you can probably buy just the o-ring from any ...   05-17-2011 01:04 pm