When I did the body of my car I built a rotissere and mounted the body on that. I was able to spin it around ...   10-30-2011 07:56 pm

Since I had some time and was going by an Dodge dealer that's been around for a long time I thought I would see what ...   09-21-2011 08:29 pm

Frank, Phil Anderson and I just went through this a couple of days ago. The number above what looks like the Chrysler pentagon is 3670119. The pentagon ...   09-21-2011 05:12 pm

I am guessing you mean 'it hits the road' when going over a bump or pothole. If it's also on a reguler smooth flat road, ...   09-03-2011 08:26 pm

There's probably a small ridge of rust blocking the drum from coming off. The area where the shoes rub against the drum are smooth and ...   08-17-2011 01:06 am

It's been a year since I rebuilt the front suspension so things may be a little fuzzy. But when I took things apart I saw ...   07-30-2011 08:18 pm

Just some rambling here on the information provided so far and my general opinion. There isn't that much difference between the 73 and 74. Remember all ...   07-01-2011 06:54 pm

There appears to be a difference between the cars and parts I have here. My 73's lower dash looks to be all one piece of thin ...   06-24-2011 07:48 pm

Matt, Try going to http://www.deltamotorsports.com/products/pg11a-steering-column-cowl-heater-andtransmission-controls.html and you will be able to see the part. Jody's site has the part number listed on the bottom but there is no ...   06-22-2011 11:43 pm

Buy both and you have your own source of parts. The differences between the trans is small in my opinion. Both have the same final ratio ...   06-19-2011 04:00 pm

I think I saw one yesterday while I did inventory of the boxes in the shed. If I understand your request correctly. But I think you have ...   06-19-2011 03:48 pm

Fixing the clutch cable should help with some of issues. Also find out what fluid was used if it was changed when the new clutch ...   06-18-2011 09:59 pm

I'm sure you thought of this already but just in case... Since you mentioned you know the hoses are old since you will be replacing one ...   06-18-2011 09:44 pm

I know this doesn't offer any help but this is the reason I went with 15" rims and tires last year when I bought some ...   04-23-2011 01:53 am

Sounds like me and my car. Making a lot of changes also. I got a GT that turned into a parts car so I am ...   04-03-2011 03:37 am

What did you do for the center console? Use the one from a JH or did you have one from a GT? I have both a ...   04-02-2011 10:12 pm

That's what I remember mine looking like. ...   03-11-2011 02:55 pm

I'll have to look and see if I still have one. It was missing on one of the cars, badly replaced with chicken wire on ...   03-11-2011 01:38 am

They are just pressed on. When I took mine off a few years ago I believe I just twisted and pushed the top to the ...   03-02-2011 03:33 am

I believe this has been discussed before but I think it was discussed on the old board. So it has been quite a while. And I ...   02-28-2011 02:44 pm

Also you want to note the bottom position of the shaft. There is a "key" so to speak on the bottom that fits into a ...   02-26-2011 04:53 am

I measured a couple and they were 16". As for where to buy what kind of auto parts stores are near you? Or you could call ...   01-28-2011 02:37 pm

Heck. I'll probably need one at some time. ...   01-20-2011 12:57 am

Cool. That means we might have 5 cars there. So far there are two JHs and two Interceptors. Woo Hoo! ...   01-15-2011 07:07 pm

The meeting is happening this Saturday with the plan to meet by the McDonalds at 3:00 PM. Hoping to beat the rush of cars from ...   01-11-2011 10:51 pm

Funny you should ask Kurt. I got one with the GT parts car and have it apart and some of the measurements made to make ...   12-31-2010 06:28 pm

I was at Delta Motorsports yesterday and Jim is looking at having this reproduced. He had the pieces setting on the counter waiting to go ...   12-29-2010 08:59 pm

Saturday, Jan. 15, 2011. This is the beginning weekend of the show here in Scottsdale and they are having their 2nd annual Barrett-Jackson Night at the ...   12-24-2010 12:04 am

The parts were purchased from Delta Motorsports. When I rebuilt I cleaned the rack, media blasted, primed and painted. Then replaced the balljoint ends, gaiters, clamps ...   11-27-2010 01:54 am

As Kurt mentioned the factory used 80/90w gear oil. 4 ounces is the recommended amount. Search for a thread titled "Steering Rack Lubrication" for a discussion ...   11-26-2010 03:40 am

If your cable was like one of mine there is a sort of catch that you press and then pull back on the cable. It ...   11-08-2010 01:58 am

To add what Jody said. There were eight of us today and everyone had a great time. As Jim Medland from Delta Motorsports mentioned there ...   11-07-2010 02:42 am

OK. The last reminder for this meeting. The weather is going to be great so come out and meet your fellow Jensen Owners. This Saturday, Nov. ...   11-04-2010 06:52 pm

The date is set for Saturday, November 6, 1:00PM at the 5 & Diner on the East side of the Arizona Mills shopping mall. The ...   10-24-2010 05:17 am

I don't know that Autozone and such will have them. Maybe a place like Napa or BAP Imports might have them. That being said I have ...   10-24-2010 04:57 am

OK. Let's try this again. Jody and I were talking and decided it's time to try and have another AZ Jensen meet. The choices are ...   10-17-2010 02:52 am

Brings back memories from long ago when racing there and working the SCCA June Sprints, the Trans-Am races in July and the Can-Am races in ...   10-17-2010 02:39 am

I've got one. I sent you a private mail. Art ...   09-30-2010 03:21 pm

I have a box with some calipers from a 74 JH somewhere around here. I looked for it yesterday but could not find it. I'll ...   09-06-2010 08:20 pm

My bad. I did mean 3/8" for the rotor thickness. I've heard the TR-7 calipers fit also. But have never confirmed that to be true. Amongst my ...   09-05-2010 07:57 pm