| ||||
|
Posts by Dan (Florida) | |
---|---|
97 posts | Showing posts 81-97 of 97 |
Ignition > engine cranks, but won't start (6 replies - 15895 views) I've had an unusual no start situation before and it may pay you to check if the distributor hasn't jumped out of its drive on ... 03-07-2007 02:21 pm Miscellaneous > 0-60 times (7 replies - 18922 views) I guess that is one of the percs car testers get when testing new cars that they don't own , getting to do stuff you wouldn't do ... 12-05-2006 11:18 pm Miscellaneous > 0-60 times (7 replies - 18922 views) Was just wondering what 0-60 times everyone else with stock/modified JH's were getting. I can only get around 13 seconds with known mixture problems in ... 12-04-2006 01:30 am VIN Database for Jensen Healey & Jensen GT > Jensen Healey & Jensen GT VIN Database (342 replies - 541572 views) 19444, all original except crane ignition and Delco single wire alternator. Don't have engine number, but is the rope seal style. Original home was Green ... 11-24-2006 12:12 pm Miscellaneous > information card (5 replies - 11575 views) 19444 is in fair shape, good enough to show on Saturday nights at the local "run what you brought" shows. Being relatively rare in Florida ... 10-17-2006 11:52 pm Miscellaneous > ebay race car? (2 replies - 7647 views) fyi anybody else seen the J/H race car on ebaymotors under race cars. Item #130004782014. ... 07-13-2006 02:53 pm Engine & Transmission > REBUILD CLARIFICATION (6 replies - 12740 views) Remember,when grinding valves and seats the valves sink deeper into the head reducing the clearance to the cam. If enough is removed the cam will ... 04-13-2006 12:16 pm Engine & Transmission > Ignition Timing (9 replies - 15558 views) It's happened a few times but usually when I loosened the clamp to adjust the timing and not notice the distributor hopping out of the drive. ... 07-29-2005 11:33 am Engine & Transmission > Cam belt tension/ tensioner (12 replies - 21343 views) Well, as another postscript to the whining cam belt, I finally loosened the cam belt to a 90 degree twist, which seems mighty loose and ... 07-27-2005 04:05 pm Engine & Transmission > Ignition Timing (9 replies - 15558 views) My timing used to slip like that , but it was the distributor was not pushed in far enough. There is a spring between the ... 07-22-2005 12:36 am Engine & Transmission > Cam belt tension/ tensioner (12 replies - 21343 views) Well, as a postscript the tensioner bearings have been changed and the whine remains causing a further look at the belt sprockets which are pretty ... 07-22-2005 12:29 am Engine & Transmission > Cam belt tension/ tensioner (12 replies - 21343 views) Once again, thanks for the info, always appreciated.
ps Hope hurricane Emily saves a little rain for that part of the country. Sounds kind of warm.
Dan
... 07-18-2005 12:26 pm Engine & Transmission > Cam belt tension/ tensioner (12 replies - 21343 views) I put new cam belt idler bearings in about six months ago and the new bearings are now whining and must be replaced. I guess ... 07-17-2005 03:52 pm Engine & Transmission > Oil pan removal, (rope seal engines) (4 replies - 12538 views) Thanks for the come back, The leak is up to around 2 quarts a week if I drive several times a week. Its bad enough ... 05-24-2005 11:38 pm Engine & Transmission > Oil pan removal, (rope seal engines) (4 replies - 12538 views) The rear oil seal leak is getting worse and looking more toward replacement time. It doesn't look like an easy job and I was wondering ... 05-22-2005 11:55 pm Ignition > Low power Poor performance (11 replies - 22675 views) Just to add my 2 cents, I would check to see if the slides are going up and down as the throttle is blipped. The ... 04-06-2005 02:39 pm Engine & Transmission > Rear Oil seal/ cam adjuster (0 replies - 6412 views) I have a rear oil seal that came with the car that I cannot use since the engine requires the older rope seal. I don't ... 03-16-2005 01:02 pm | |
Current time is 07:44 am | 1 2 3 |