removing the front seats bolts was always difficult task for my JH. here's way. First, there is a full rear seat lock position that allow's easy ...   11-01-2018 05:55 pm

They are delrin washers, I was told when rebuilding mine they are not required after the needle asm is installed into the air valve. The ...   10-31-2018 11:57 pm

has anyone checked the vacuum reading off the intake manifold fitting to the brake booster. I checked mine at idle it shows 15 inHg at ...   10-31-2018 03:28 pm

does anyone know where to get the square hole perforated pattern for the bucket seats insert fabric or original manufacturer specs. update: bought round hole perforated vinyl ...   08-25-2018 02:01 pm

thanks , i'll take apart the switch and investigate. ...   08-14-2018 11:02 pm

light switch -what was jensen healey's original purpose position 1 = off position 2 = on -(my JH is lo beam and running lights) position 3 = on ...   08-14-2018 03:12 pm

during hot weather and driving for a while my engine is hard to start after a 5 - 10 min rest. engine temp goes up ...   08-11-2018 11:48 am

my Jensen after a half hour drive, started off from stop light it started sputtering ( loss of power ) then stalled, i looked under ...   07-21-2018 01:11 am

Speedo update. Got the speedo serviced at scottspeedometer.com. They’re in Pontiac Michigan. Speedo needed only a good cleaning, I did 2 of them . ...   12-09-2017 01:03 pm

Trans fluid for 5 speed transmission, manual specs out 20w/50 motor oil? Also , specs 80 weight. What are others using? Little more info on what I ...   12-01-2017 07:38 pm

My 5 speed trans sticks in reverse and 1st gear when cold. After warm up it’s fine. What causes this ... trans fluid type, a ...   10-06-2017 08:09 pm

My speedo stopped working , so I bought a new cable. I tested the speedo installed with an electric drill replacing the trans pinion connection. ...   09-20-2017 11:19 pm

Need new one. Need to know part number, source and price? ...   09-17-2017 12:21 pm

Email me at 07vette47@gmail.com And I will email you back a copy of the PDF. John ...   07-31-2017 08:37 pm

I fabricated an AirDam with materials I bought at local homedepot. I have a " how to " pdf with full size templates when ...   07-31-2017 02:05 am

Rear Ebrake installation, I sent out a revised version 1.0 to all I sent out copies of the first version. I added a tactical and ...   07-15-2017 11:41 am

Rich, Could you post a bill of material ,source and cost for the trans conversion. And any problems you had to overcome. I currently have the 5 ...   04-11-2017 12:33 am

I have a PDF on how I did my rear brake conversion. Send a request to me at: 07vette47@gmail.com I'll email you ...   03-22-2017 10:53 pm

Thanks for everyone's interest in rear disc. I Will talk with the laser cut supplier monday, should have everything together this week to release PDF ...   03-19-2017 11:03 pm

I finished may assembly guide what use and did, also received a quote from a laser cut source. Only leaves me with getting samples of ...   03-17-2017 03:48 am

Working with a supplier who will make laser cut brackets, you can order direct from them. Installation document will be done soon. Hang in ...   02-20-2017 01:52 am

Yes, I got a reply from Martin Robey early JH 's had a large dust shield with seal. Prying off is all you do. Thanks ...   02-07-2017 02:27 am

Working on providing details ...   02-06-2017 12:16 pm

I engineered this setup from off the shelf calipers and rotors with working emergency brake. Designed custom mounting plates, they are bolt on but can ...   02-04-2017 01:07 am

Diagram doesn't show part, part is attached to backside of rotor. When you pull the hub off the rotor and mystery part is attached. I ...   02-04-2017 12:39 am

What did the spark plug look like as compared to the others, ...   02-03-2017 11:32 pm

When inspecting the front bearing I removed the hub rotors asm, looking to separate the rotor from the hub . But I found a ...   02-03-2017 11:23 pm

Reply FYI>>>> about timing belts: there are numerous tooth patterns that look similar but are different, lotus used belt part number A907E0191ZE. i only buy ...   01-20-2017 01:43 am

what is the cost ? US $ and shipping charge. ...   01-20-2017 01:34 am

10mm thick design , min thick 8mm ...   01-20-2017 01:11 am

Clutch release bearing 4 speed trans vs 5 speed trans are they the same Cross reference parts numbers ...   11-14-2016 12:04 am