Hi Rich, I sent a PM to you regrading a stock fuel tank I have that I'm not using. It's fairly clean (sat for many years ...   05-26-2018 04:33 pm

Steve, As others have commented, a drill and a hacksaw blade is probably the best method. If you're comfortable with it, especially with the diff in ...   04-01-2018 07:36 pm

The bracket on the driver's side makes it quick and easy to center the console during assembly. But that's not from any official sources, just ...   03-26-2018 02:02 am

Hi Stu, It sounds as if what you've done is correct - tapping those tabs until the lock ring is tight and not bending them. It's ...   06-20-2017 04:18 pm

Hi Stu, Great to hear it's on the road. Regarding the knock, have you checked the exhaust? That's right about where it passes over the differential. ...   06-15-2017 05:30 pm

...   06-13-2017 06:58 pm

I don't have a cross reference on the wheel cylinder; I researched this some time back and recall there is a match but don't have ...   05-27-2017 04:47 pm

Frank, PM me your contact info as I have a brand new Delta set in black I'd be willing to part with. Clinton ...   04-09-2017 05:08 am

Sawyer: I also have numerous pics of my brakes I could send you if needed. Also, Nigel's advice is spot-on as my brakes now adjust without ...   03-12-2017 05:42 pm

Hi; I'm not certain what you need, but perhaps this item on ebay is one of them: http://www.ebay.com/itm/JENSEN-HEALEY-RIGHT-REAR-PILLAR-ASSEMBLY-/232168378822?hash=item360e5051c6:g:inwAAOSwo4pYSZEn&vxp=mtr Clinton ...   03-12-2017 05:39 pm

Do you know the manufacturer? Contact the company that made it and ask for a copy of instructions. They could just email it to you. ...   03-12-2017 04:55 am

I have a top that has seimilar needs and this is the product I'll probably try. No spray equipment needed and very little investment if ...   02-14-2017 05:01 pm

I just received new rear springs for 18341 and am installing them. I have a question about the steel peened bushing/retainer that holds the mounts ...   01-21-2017 11:05 pm

Thanks for the heads-up. No mention of the JH, and the owner even stated that the Interceptor was Jensen's most successful car with over 6000 ...   12-26-2016 05:27 pm

Just wanted to say Merry Christmas, Happy Holidays and Happy New Year to all in the JH Society. I've learned too much from the postings ...   12-25-2016 07:36 pm

I went to the website some months back (after he passed) and and tried to make contact but never got a response. The site hasn't ...   12-06-2016 09:22 pm

Tim, Thank you for not only the usual technical expertise but for some perspective as well. I'd like to get lucky on this but getting lucky ...   11-30-2016 10:11 pm

I just got #18341 running. This is a car I picked up for parts - the owner parked it in 1988 and it didn't move ...   11-25-2016 09:40 pm

I learned about poor/corroded grounds with a TR6 I had years ago. An old mechanic told me when entire sets of accesories work intermittently, look ...   11-22-2016 09:23 pm

There are a couple of sources for new tanks if the repair doesn't work out (or you feel like spening the money). I was looking ...   11-18-2016 05:35 pm

Yes, the hidden studs/nuts are the ones referenced by Brett - just under the coolant holes. And yes, I also had to remove all of ...   11-18-2016 01:40 am

I wanted to add this note: I just removed the intake manifold (ZS carrbs) from #18341. Eleven studs with nuts on all of them, including ...   11-16-2016 04:52 am

Nice work; we could all use something like that. ...   11-07-2016 05:33 pm

Qwerty, I, too, ran one for many miles in the wrong position as I was following the instructions in the WSM. Thanks to Tim's tip It ...   11-07-2016 04:39 pm

Is the "upside down" a reference to the position of the eccentric? The pic looks like it's installed according to the WSM - that is, ...   11-06-2016 04:05 pm

I have a PDF of plans for a gas strut conversion. I don't recall where I downloaded it from, but it was an update of ...   10-05-2016 02:25 am

In addition to the material under the tank, be certain the gasket around the filler tube is as good as can be well. Delta has ...   10-04-2016 07:55 pm

No need to drain... once you see it you know why. It sits so high up there's no need to do anything except disconnect the ...   09-26-2016 03:40 am

I haven't had the temp gauge problem but I'd start with the sending unit as it's inexpensive and super easy to change out. It's located ...   09-24-2016 11:47 pm

I imagine the grounds dwalls1 refers to are throughout the car. Anywhere the wiring loom grounds to the body of the car, remove the screw ...   09-24-2016 11:43 pm

Are you still running points and condenser? A few years ago I had a problem somewhat similar to yours... it wouldn't necessarily flatline but would ...   08-25-2016 04:22 pm

Nigel, Many years ago a machinist told me that it's a good idea to always put the outer bearing races in the freezer for some ...   08-20-2016 01:17 am

Congrats on the clean installation - it looks great in the photo. Were the instructions with kit all the help you needed? I could see ...   08-08-2016 03:06 pm

Just a caveat regarding the Eastwood product: I was looking into this a couple of years ago and changed plans after reading some of the reviews ...   07-24-2016 04:56 pm

...   07-18-2016 06:38 pm

azvat1; Is yours a JH5? Just curious as I have 19451 which came without badging. I've read where some of the cars in this sequence ...   07-18-2016 06:38 pm

I'llI assume we're talking about the lock mechanism (the part with the key.) Drop the steering column (four bolts as I recall). The lock is ...   07-14-2016 12:47 pm

This thread from last year may be helpful, with special attention to Nigel K's comment farther down the page: http://www.jensenhealey.com/forums/view_topic.php?id=1483&forum_id=7 Clinton ...   05-26-2016 07:12 pm

This explanation may help - read down to Mark Rosenbaum's answer on tach wiring: http://www.jensenhealey.com/forums/view_topic.php?id=86 ...   05-21-2016 06:44 pm

If the wire in question is white/yellow (look carefully, even after cleaning those colors really fade) it should go to the positive coil. The ballast resister ...   05-21-2016 06:21 pm