I'm working on a W58 conversion at present. I have scored a CUBE short throw shifter from down under for $130. I had to replace ...   03-15-2016 11:56 pm

Order of operations is remove hand brake screws from tunnel. Then you can remove the center console. Remove the gear lever and don't ...   07-28-2015 10:09 pm

Does any one have another one of these? 11602 came with only one. After I removed the roof frame from the body I discovered the missing ...   02-27-2015 01:20 am

Hi Subwoofer, No the leak is now at the end of the header were it goes into the y collector at the start of the main ...   02-28-2014 03:09 am

I put one of these in the dash last Sunday, were the clock would have been if it had one! INNOVATE 3844 MTX-L DIGITAL WIDE-BAND ...   02-14-2014 05:29 pm

Hello Gordon, I think your thermostat is a very good idea with the cooler weather in England. This winter in Southern California has been a ...   12-08-2013 07:37 pm

In many of the forum-threads the oil filter type seal which keeps the adapter fixed to the auxiliary housing can be a source for leaking. ...   12-08-2013 01:35 pm

Subwoofer, Just like the float level numbers I did a search on "DCOE fuel level" I have found references to 25mm and 29.5mm being the right ...   11-30-2013 03:46 am

Yup it sure does. But the Addco chassis mounted bars end up having a longer effective arm as they are rear set by quite ...   11-30-2013 01:16 am

Hey Chaps, I have a pair of Weber 45DCOE9's on 11602 and I have been experimenting with the float height. I noticed that the 8.5mm ...   11-27-2013 04:15 pm

Well I figured out why my fuel gauge in 11602 would not read below 1/4. The float was installed in the arm the wrong ...   11-19-2013 02:36 am

Well 11602 came with a box of parts, and in this box was this fuel pump with a dash of red paint overspray on the ...   11-16-2013 02:35 pm

I was wondering about those other holes in the sub frame as they looked like they could harbor a sway bar. The bushing which fixes the ...   10-28-2013 04:58 pm

This angle allows the bushing stack to match the angle of the A-arm's tabs which come on the OEM suspension's lower arms . What ...   10-24-2013 09:48 pm

Addco Sway bar Kit Rear ...   10-23-2013 04:35 am

Addco sway bar Kit Front ...   10-23-2013 04:31 am

TaDa ...   10-23-2013 04:28 am

For the rear I welded the adapter plates to the radius arms to get as much stiffness as I could from the bracket. ...   10-23-2013 04:24 am

The Addco hardware for the front link to the A-arms are useless. I used some longer larger diameter bolts and nuts with a longer ...   10-23-2013 04:22 am

Foil Covered Bubble Wrap at you local hardware store trim to fit with razor knife. ...   10-23-2013 04:10 am

Hi Frank, I nabbed a Flywheel two weeks ago that was lightened and blanchard ground in the area of the clutch disk. The weight was ...   10-23-2013 03:47 am

Right got it all done. The exhaust screw had very oily threads and managed to flood out all over the washer as I removed ...   10-23-2013 03:17 am

Shimming washers it took two to get it just right. ...   10-23-2013 02:57 am

Hose Pipe Shot ...   10-23-2013 02:55 am

About 1-3/4" long on the hose pipe ...   10-23-2013 02:55 am

Jim, thanks for the prompt on the set screw inside the cam shaft. In researching the cam seal issue in the engine section of ...   10-22-2013 11:19 pm

So having just replaced the cam shaft seals on 11602, I drove Ortega Hwy. last Saturday to Murrieta, Ca and back. Nice hot afternoon ...   10-21-2013 10:08 pm

Slide the pipe onto the stud and look at the alighnment between the water pump and this pipe without any rubber hose in the way.  ...   10-21-2013 08:57 pm

Oh, If some of you are looking at this and thinking this guy is an idiot because he has glued the two halves of his ...   10-07-2013 08:12 pm

Mk II rear main seal carrier on a Mk I block.  Just some drilling and tapping and no machine work needed on the block.  I did ...   10-07-2013 07:56 pm

I just went through cleanng up and repainting the black on the original wheels and the "rubber/plastic" cap does a poor job if not non ...   09-16-2013 04:42 pm

Hi Greg, Understood, as mine is 11602 it fell right into that "early" relm. From the look of the fresh oil wetting the tunnel and ...   09-03-2013 07:55 pm

The Spyida conversion kits needle damping can be changed but Chris who I have been in dialog with has indicated that to do this requires ...   08-28-2013 01:53 pm

Ran into a few issues with the Spyida RVI to RVC repalcement PCBA kit. The VDO is looking a bit more appealing at this ...   08-27-2013 08:55 pm

I got the car back together on Saturday and put 40 miles on the Speedometer. Got here up to some where north of 5,000 RPM ...   08-27-2013 08:30 pm

The Spyida Board replacement was started this week.  I'll have snipped the white wire that goes through the torrodial doughnut inside the tachometer and replaced ...   08-22-2013 08:06 pm

I used to work on wind mills back in the 80's. We used a lot of F911 (better than grade 8) fasteners for mounting ...   08-11-2013 02:48 pm

Art I hope I get more than a few years out of the new bushing? But too that end has anyone thought about covering ...   08-09-2013 09:50 pm

This Champion 3 row core radiator was the second thing I got for VIN #11602. The cap will draw coolant back from an overflow tank ...   08-09-2013 09:38 pm

VIN#: 11602, Engine: B73 02 1791 Cleaned up the flywheel, clutch-disk and pressure plate yesterday. It was un seated from the flange on the flywheel ...   08-09-2013 02:08 am