Home 
Home Search search Menu menu Not logged in - Login | Register
> redracer

Profile Topics Posts
Posts by redracer
617 postsShowing posts 81-120 of 617

Body & interior stuff > So this bracket is just hanging out here.... (6 replies - 4140 views)

That's the support for the "frame" side of the engine dampener, which you are missing. The other end of the dampener attached to another steel ...   05-21-2022 01:57 pm

Miscellaneous > New member from New Jersey (4 replies - 2427 views)

Very interesting; so, does the car run and drive now? ...   05-17-2022 11:31 pm

Carburetors > accelerator cable (3 replies - 2492 views)

You'll need to slither upside down under the dash. Take a long thin flat bladed screwdriver to remove the clip on the end of ...   05-15-2022 02:25 pm

Engine & Transmission > Engine pisotns or liners (2 replies - 2164 views)

DBE(Dave Bean Engineering) has some ; just ordered +0.030 J&E with rings. Ken should be able to help. Address: 636 E St Charles St, San Andreas, CA ...   05-12-2022 09:21 pm

Miscellaneous > JENSEN NATIONAL--Hiawassee, GA. (2 replies - 1764 views)

Rob Wester is hosting this year, back where it started when Aaron(Arnold) Gross was the host: https://mail.google.com/mail/u/0/?ui=2#label/JENSEN+National%2C+2022/FMfcgzGmtXJFfnrwqztnjlZWqXXXSVSD?projector=1&messagePartId=0.1.1 ...   05-05-2022 10:47 pm

Miscellaneous > Jensen Healey MkI "Standard" Pictures? (1 reply - 1449 views)

I could likely help you with whatever; I don't have any '73s(except the Huffaker race car). If you get specific on what you want to ...   05-03-2022 02:23 pm

Body & interior stuff > GT interior problems. (6 replies - 3752 views)

I don't have a GT whole glovebox lock assembly(the 2 GTs I stripped, only one had a lock and Frank Schwartz got that one a ...   04-04-2022 09:29 pm

Body & interior stuff > GT interior problems. (6 replies - 3752 views)

Sorry; I didn't catch this thread last year when it came out. Do you need an actual tumbler/lock for the glove box? (should use the ...   03-15-2022 12:18 am

Cooling > Original brake master cylinder and reservoir (1 reply - 1953 views)

fellow Jensenites: I thought most of you knew this, but Dave Bean Engineering(San Andreas) has them now at a VERY reasonable price. Rather than converting ...   03-02-2022 07:11 pm

Cooling > Water Pump -"SANDBLASTED"--AGAIN (3 replies - 2188 views)

Can't figure out anymore how to post an image on this thing' Go back to the earlier one I did--another ruined housing http://www.jensenhealey.com/forums/view_topic.php?id=2682&forum_id=3&highlight=water+pump%2C+bruce ...   03-01-2022 02:46 pm

Cooling > Water Pump -"SANDBLASTED"--AGAIN (3 replies - 2188 views)

...   03-01-2022 02:42 pm

Cooling > Water Pump -"SANDBLASTED"--AGAIN (3 replies - 2188 views)

...   03-01-2022 02:40 pm

Cooling > Water Pump -"SANDBLASTED"--AGAIN (3 replies - 2188 views)

Here's a "recent" rebuild on another ruined housing thanks to those spiral steel cored radiator hoses. ...   03-01-2022 02:39 pm

Ignition > Starter problem (6 replies - 3771 views)

mr, Loco & Don: the logic box scenario has been written up many times, even back to the late '70s. Yes, if you're seat ...   01-12-2022 05:43 pm

Miscellaneous > Car going to new owner (4 replies - 2616 views)

Ah--okay. So you're Ronald Tarr; remember trying Hylomar on your rear housing and leaking(don't use that anymore for normal gasket sealing--back to Permatex #2) Glad to ...   01-02-2022 05:13 pm

Miscellaneous > Car going to new owner (4 replies - 2616 views)

Jim Reilly (in Coram) has 40+ years experience. Here's his info: jimreilly43@hotmail.com • Home (631)938-3069 • Jim(cell) Coram, NY 11727 I believe he may be trying soon ...   01-02-2022 03:47 pm

Engine & Transmission > Pulley & Cam Belt Correct? (6 replies - 3265 views)

okay--so please call/skype as you could be one tooth off and still drive the car. Also, the belt must be tensioned with a cold engine, ...   01-02-2022 03:06 pm

Engine & Transmission > Pulley & Cam Belt Correct? (6 replies - 3265 views)

I can not tell from the pic even after enlarging it. Please do NOT turn over the engine if not sure. Putting a straight edge between ...   01-02-2022 02:50 pm

Cooling > Water pump pulley position (4 replies - 2787 views)

The belt pulley is not adjustable(I have never heard anyone try to shim it); the center portion fits around the protruding nose of the hub(where ...   12-30-2021 04:51 pm

Wheels > Jensen Healey Extended length wheel studs - "knurl" dimension? (10 replies - 7045 views)

Interesting last photo; looks like you have the press in your library! ...   12-06-2021 02:01 pm

Wheels > Jensen Healey Extended length wheel studs - "knurl" dimension? (10 replies - 7045 views)

For pressing both the bearing and locking collar on, I went to our local hardware store and got/had made a length of pipe that just ...   11-30-2021 09:12 pm

Wheels > Jensen Healey Extended length wheel studs - "knurl" dimension? (10 replies - 7045 views)

Disco: have done many of these bearing replacements. Use a small cut-off wheel(think DREMEL) and cut the retainer at angles until nearly through. A chisel ...   11-29-2021 06:32 pm

Miscellaneous > Steering geometry (2 replies - 2083 views)

There is no adjustment for camber. If you wish to adjust it, you will need to make a sliding plate for the top ball joint ...   11-19-2021 10:53 pm

Engine & Transmission > Oil pan gasket or seal replacement (10 replies - 5191 views)

Having worked on "many", I have looked at that long ago and decided it was not worth the effort. If I remember correctly, you ...   11-08-2021 12:04 am

Engine & Transmission > Oil pan gasket or seal replacement (10 replies - 5191 views)

Agree strongly with Tim's recommendations along with the possible calamity of oil pick-up tube blockage. Personally, I would use silicone ONLY on the water pump ...   11-07-2021 02:47 pm

Engine & Transmission > Piston compression cold (8 replies - 4349 views)

85 psi for all 4 should be fine after such a long layover,. The spark you are getting is at the spark plug I ...   10-25-2021 04:15 pm

Body & interior stuff > Tonneau (7 replies - 4365 views)

Doesn't look too bad! btw: Pilkington has been selling J-H windscreens for a long time. Not sure if you had contacted them, but their cost used ...   10-16-2021 01:11 am

Body & interior stuff > Tonneau (7 replies - 4365 views)

For $180, that's a pretty good deal. If they were to advertise that, they would likely get a good bit more business. ...   10-15-2021 05:33 pm

Body & interior stuff > Tonneau (7 replies - 4365 views)

The original tonneau covers are the same way; you need to lay the seats back for clearance!! At least they made a slot for the ...   10-15-2021 04:16 pm

Engine & Transmission > fan bolt size (3 replies - 2585 views)

The original bolts(the hub is round) are 1/4"X20, as Brett stated. However, the aftermarket ones(NOT round; cast ) use 1/4"X28 ...   10-15-2021 04:14 pm

Accessories > Replacement sun visors? (13 replies - 23775 views)

The notch part of the visor goes on the outside. Hopefully, you will be able to get the machine screws out as they easily get ...   10-10-2021 10:29 pm

Electrical & Instruments > Hazard Rocker Switch (9 replies - 11145 views)

Ha, Ha! No, I certainly would not have repaired it "upside down"! Either someone else came up with the same idea or they took ...   10-10-2021 10:06 pm

Electrical & Instruments > Hazard Rocker Switch (9 replies - 11145 views)

Don: interesting that your old HAZARD switch had a set screw. It was very likely one I had fixed a long time ago, as the ...   10-09-2021 05:49 pm

Miscellaneous > New JHPS Member - Southern New Jersey (18 replies - 7944 views)

WELCOME! Not sure if 6'5" would be too tall, but a friend who is 6'3" fits fine. There is a "SEARCH" box at the top ...   10-06-2021 12:40 pm

Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views)

FINAL "WRINKLE" FINISH AFTER BAKING ...   10-01-2021 05:44 pm

Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views)

...   09-30-2021 09:17 pm

Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views)

...   09-30-2021 09:17 pm

Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views)

...   09-30-2021 09:16 pm

Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views)

...   09-30-2021 09:16 pm

Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views)

...   09-30-2021 09:16 pm


 Current time is 11:41 am
 First Page Previous Page  1  2  3  4  5  6  7  8  ...  Next Page Last Page


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems