| ||||
|
Posts by redracer | |
---|---|
617 posts | Showing posts 81-120 of 617 |
Body & interior stuff > So this bracket is just hanging out here.... (6 replies - 4139 views) That's the support for the "frame" side of the engine dampener, which you are missing. The other end of the dampener attached to another steel ... 05-21-2022 01:57 pm Miscellaneous > New member from New Jersey (4 replies - 2427 views) Very interesting; so, does the car run and drive now? ... 05-17-2022 11:31 pm Carburetors > accelerator cable (3 replies - 2492 views) You'll need to slither upside down under the dash. Take a long thin flat bladed screwdriver to remove the clip on the end of ... 05-15-2022 02:25 pm Engine & Transmission > Engine pisotns or liners (2 replies - 2164 views) DBE(Dave Bean Engineering) has some ; just ordered +0.030
J&E with rings. Ken should be able to help.
Address: 636 E St Charles St, San Andreas, CA ... 05-12-2022 09:21 pm Miscellaneous > JENSEN NATIONAL--Hiawassee, GA. (2 replies - 1764 views) Rob Wester is hosting this year, back where it started when Aaron(Arnold) Gross was the host:
https://mail.google.com/mail/u/0/?ui=2#label/JENSEN+National%2C+2022/FMfcgzGmtXJFfnrwqztnjlZWqXXXSVSD?projector=1&messagePartId=0.1.1 ... 05-05-2022 10:47 pm Miscellaneous > Jensen Healey MkI "Standard" Pictures? (1 reply - 1449 views) I could likely help you with whatever; I don't have any '73s(except the Huffaker race car).
If you get specific on what you want to ... 05-03-2022 02:23 pm Body & interior stuff > GT interior problems. (6 replies - 3752 views) I don't have a GT whole glovebox lock assembly(the 2 GTs I stripped, only one had a lock and Frank Schwartz got that one a ... 04-04-2022 09:29 pm Body & interior stuff > GT interior problems. (6 replies - 3752 views) Sorry; I didn't catch this thread last year when it came out. Do you need an actual tumbler/lock for the glove box? (should use the ... 03-15-2022 12:18 am Cooling > Original brake master cylinder and reservoir (1 reply - 1953 views) fellow Jensenites: I thought most of you knew this, but Dave Bean Engineering(San Andreas) has them now at a VERY reasonable price.
Rather than converting ... 03-02-2022 07:11 pm Cooling > Water Pump -"SANDBLASTED"--AGAIN (3 replies - 2188 views) Can't figure out anymore how to post an image on this thing'
Go back to the earlier one I did--another ruined housing
http://www.jensenhealey.com/forums/view_topic.php?id=2682&forum_id=3&highlight=water+pump%2C+bruce ... 03-01-2022 02:46 pm Cooling > Water Pump -"SANDBLASTED"--AGAIN (3 replies - 2188 views) ... 03-01-2022 02:42 pm Cooling > Water Pump -"SANDBLASTED"--AGAIN (3 replies - 2188 views) ... 03-01-2022 02:40 pm Cooling > Water Pump -"SANDBLASTED"--AGAIN (3 replies - 2188 views) Here's a "recent" rebuild on another ruined housing thanks to those spiral steel cored radiator hoses. ... 03-01-2022 02:39 pm Ignition > Starter problem (6 replies - 3771 views) mr, Loco & Don: the logic box scenario has been written up many times, even back to the late '70s. Yes, if you're seat ... 01-12-2022 05:43 pm Miscellaneous > Car going to new owner (4 replies - 2616 views) Ah--okay. So you're Ronald Tarr; remember trying Hylomar on your rear housing and leaking(don't use that anymore for normal gasket sealing--back to Permatex #2)
Glad to ... 01-02-2022 05:13 pm Miscellaneous > Car going to new owner (4 replies - 2616 views) Jim Reilly (in Coram) has 40+ years experience. Here's his info:
jimreilly43@hotmail.com • Home
(631)938-3069 • Jim(cell)
Coram, NY 11727
I believe he may be trying soon ... 01-02-2022 03:47 pm Engine & Transmission > Pulley & Cam Belt Correct? (6 replies - 3265 views) okay--so please call/skype as you could be one tooth off and still drive the car. Also, the belt must be tensioned with a cold engine, ... 01-02-2022 03:06 pm Engine & Transmission > Pulley & Cam Belt Correct? (6 replies - 3265 views) I can not tell from the pic even after enlarging it. Please do NOT turn over the engine if not sure.
Putting a straight edge between ... 01-02-2022 02:50 pm Cooling > Water pump pulley position (4 replies - 2787 views) The belt pulley is not adjustable(I have never heard anyone try to shim it); the center portion fits around the protruding nose of the hub(where ... 12-30-2021 04:51 pm Wheels > Jensen Healey Extended length wheel studs - "knurl" dimension? (10 replies - 7045 views) Interesting last photo; looks like you have the press in your library! ... 12-06-2021 02:01 pm Wheels > Jensen Healey Extended length wheel studs - "knurl" dimension? (10 replies - 7045 views) For pressing both the bearing and locking collar on, I went to our local hardware store and got/had made a length of pipe that just ... 11-30-2021 09:12 pm Wheels > Jensen Healey Extended length wheel studs - "knurl" dimension? (10 replies - 7045 views) Disco: have done many of these bearing replacements. Use a small cut-off wheel(think DREMEL) and cut the retainer at angles until nearly through. A chisel ... 11-29-2021 06:32 pm Miscellaneous > Steering geometry (2 replies - 2083 views) There is no adjustment for camber. If you wish to adjust it, you will need to make a sliding plate for the top ball joint ... 11-19-2021 10:53 pm Engine & Transmission > Oil pan gasket or seal replacement (10 replies - 5191 views) Having worked on "many", I have looked at that long ago and decided it was not worth the effort. If I remember correctly, you ... 11-08-2021 12:04 am Engine & Transmission > Oil pan gasket or seal replacement (10 replies - 5191 views) Agree strongly with Tim's recommendations along with the possible calamity of oil pick-up tube blockage. Personally, I would use silicone ONLY on the water pump ... 11-07-2021 02:47 pm Engine & Transmission > Piston compression cold (8 replies - 4348 views) 85 psi for all 4 should be fine after such a long layover,. The spark you are getting is at the spark plug I ... 10-25-2021 04:15 pm Body & interior stuff > Tonneau (7 replies - 4364 views) Doesn't look too bad!
btw: Pilkington has been selling J-H windscreens for a long time. Not sure if you had contacted them, but their cost used ... 10-16-2021 01:11 am Body & interior stuff > Tonneau (7 replies - 4364 views) For $180, that's a pretty good deal. If they were to advertise that, they would likely get a good bit more business. ... 10-15-2021 05:33 pm Body & interior stuff > Tonneau (7 replies - 4364 views) The original tonneau covers are the same way; you need to lay the seats back for clearance!! At least they made a slot for the ... 10-15-2021 04:16 pm Engine & Transmission > fan bolt size (3 replies - 2585 views) The original bolts(the hub is round) are 1/4"X20, as Brett stated. However, the aftermarket ones(NOT round; cast ) use 1/4"X28 ... 10-15-2021 04:14 pm Accessories > Replacement sun visors? (13 replies - 23774 views) The notch part of the visor goes on the outside. Hopefully, you will be able to get the machine screws out as they easily get ... 10-10-2021 10:29 pm Electrical & Instruments > Hazard Rocker Switch (9 replies - 11145 views) Ha, Ha! No, I certainly would not have repaired it "upside down"! Either someone else came up with the same idea or they took ... 10-10-2021 10:06 pm Electrical & Instruments > Hazard Rocker Switch (9 replies - 11145 views) Don: interesting that your old HAZARD switch had a set screw. It was very likely one I had fixed a long time ago, as the ... 10-09-2021 05:49 pm Miscellaneous > New JHPS Member - Southern New Jersey (18 replies - 7944 views) WELCOME! Not sure if 6'5" would be too tall, but a friend who is 6'3" fits fine.
There is a "SEARCH" box at the top ... 10-06-2021 12:40 pm Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views) FINAL "WRINKLE" FINISH AFTER BAKING ... 10-01-2021 05:44 pm Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views) ... 09-30-2021 09:17 pm Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views) ... 09-30-2021 09:17 pm Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views) ... 09-30-2021 09:16 pm Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views) ... 09-30-2021 09:16 pm Body & interior stuff > Cam Cover Painting & Prep work (12 replies - 5714 views) ... 09-30-2021 09:16 pm | |
Current time is 08:36 am | 1 2 3 4 5 6 7 8 ... |