There was some talk long ago on the Internet about this...I have retained a few of the comments with credit for such as well. In response ...   02-12-2016 04:49 am

There have been many theories as to this bothersome phenomenon. I do not have an answer. My son put a5 inch computer fan ...   02-11-2016 11:52 pm

Very odd...I logged on to Moss Motors and in the "search" mode, found nothing that matched Miata... More information, please. ...   01-23-2016 02:26 am

Definitely use your original water pump...the one in the GT has a longer shaft and will not accommodate your belt driven fan...the viscous coupled fan ...   01-17-2016 03:43 pm

Looks really good, and I plan to do the same...I recently worked on a lady's JH. It was painted pearl white and had neat dual ...   01-11-2016 06:02 pm

Somebody figured out how to fit a pneumatic hoist or whatever you call those gas charged things...anyhow, some Jensenite did fit one to his trunk ...   01-05-2016 11:07 pm

I hear good things about Joe Curto..and I have bought smaller bits and pieces from him and found him to be very helpful and friendly ...   12-09-2015 05:49 am

Not that hard to do...you0 can order rebuild kits from Delta and also needle seats and new needles, if needed, and setting up and adjusting ...   12-08-2015 04:46 am

If it is a five speed 80-90 gear oil is proper for both the rear end AND the tranny. If a four speed, ...   12-03-2015 07:48 pm

Cylinder 2 not firing? Check for a spark....... ...   11-18-2015 04:43 am

Does anyone know where I can find some good quality all metal side mirrors, driver's side and passenger..similar or as original??? Every one I found ...   11-15-2015 09:48 pm

Hi Ron...I see you are back into racing again...ae you still using that JH chassis I sold you???? I thought you had given up racing... Frank ...   11-12-2015 05:43 am

Arvin: I think Delta sells the needles and you would probably want to get the seat as well...I also think Bruce Madden has them...in fact, I ...   11-03-2015 12:58 am

Carbs balanced and so on...but cannot get a consistant idle...I can set it and then it slowly will change...such as ..set it to 950 rpm ...   11-02-2015 04:19 pm

Working on a friends JH and we replace the coil with a Blaster (MSD) coil and the recommended resistor and used a Pertronix unit in ...   11-02-2015 04:14 pm

The problem could be a plug wire not plugged into the distributor cap..it is so tight under there that when you try to put the ...   11-02-2015 05:42 am

FYI...bought a new TR6 Master Cylinder to replace one that was bad on a friend's JH...new one looks great and is exactly as the ...   10-25-2015 08:49 pm

Are yours the originals? If so they are what, 40+ years old?? I'd recommend replacing them...you can get new ones like the originals ...   10-25-2015 07:09 am

Fuzzy thinking on my part...that should be Turns per Mile... So how many turns per mile does a Smiths JH speedo turn...or whatever it might ...   10-21-2015 06:53 am

Can anyone tell me how many turns per minute equates to on the dial. Such as 1000 Turns per minute equals 60 Miles Per ...   10-20-2015 11:00 pm

Hving come froma car show where my Inteerceptor was put in a class with three very nice Jensen Healeys, I took first in that ...   10-13-2015 04:12 pm

Kurt: If I knew the answer, I'd write it up. Now that things are back to "normal" with 0 degrees static, it idles at 10 ...   08-08-2015 04:53 am

Well, talk about a combination of errors...mainly throttle cable hanging and a bad tachometer...things now back to normal...idle at 10 degrees, but have to change ...   08-06-2015 04:02 am

Yes, all timing marks are correct....so now I am checking fuel and air...no air leaks, removing carbs to make sure butterfly valves are completely closed...then ...   08-05-2015 05:27 pm

No luck yet. I have all the marks lined up as per the manual and I have done this a dozen times in the ...   08-05-2015 05:12 am

Yes...and this is crazy...#1 is at TDC..the mark on the crank pulley is lined up with 0 TDC and the cam markings match that is, ...   08-02-2015 05:34 am

I just put a new belt on a JH and now I cannot get the engine to run but when it does fire, it ...   08-01-2015 07:22 pm

Gentlemen: It is not the shifter shaft, etc. It is the entire shifter assembly where it bolts to the transmission way up inside the tunnel... I ...   07-28-2015 05:53 am

Seems the JH my son and I are working on has a loose 4 speed transmission shifter. It is held in place with six ...   07-27-2015 04:32 am

I tried to access John's web page but he must have changed his web page address, as what I keep typing in does not work. Anyone ...   07-07-2015 09:08 am

I have never had to use a puller on the crankshaft pulley. Remove the bolt and with a small hammer, like a ball peen hammer, ...   06-30-2015 09:14 pm

NO...but you have to remove the two wire leads to the switch to remove the pedal assembly...and remember when you put it all back together, ...   06-23-2015 08:35 am

I will check that bushing...but it seems to be fairly tight..that is the remaining steering shaft seemed to be solid and tight in situ.. ...   06-23-2015 12:14 am

That works...but don't forget also to unplug the two wire leads to the brake switch.... ...   06-23-2015 12:12 am

Clinton...nd anyone else reading the thread.....I followed your instructions and the rack definitely needed to be removed or loosened...see my comments on the bolt head ...   06-19-2015 06:12 pm

While trying to remove the steering shaft with the many u joints, I found it necessary to loosen the steering rack. There I found two ...   06-19-2015 06:07 pm

My GT (sold later) had a viscous coupled fan on it and I found a replacement from Delta Motorsports..am sure they still have them. Anyhow, ...   06-13-2015 06:11 am

Andy...I thought you were in the Atlanta area...I am in the Nashville area, not too far from you. I do have a lathe ...   06-09-2015 03:47 am

Andy, re reading you post above, since you did the job yourself, I 'd like to know where you obtained the parts.. I see you are ...   06-06-2015 03:47 pm

Interesting...I can see that the U joint right at the top of the assembly is badly worn...have replaced U joints on drive shafts, but this ...   06-06-2015 03:45 pm