Home 
Home Search search Menu menu Not logged in - Login | Register
> jdenglish

Profile Topics Posts
Posts by jdenglish
78 postsShowing posts 41-78 of 78

Engine & Transmission > W58 Clutch release bearing (18 replies - 10283 views)

Mike, "Dimensions differed"?  How then would it be an exact replacement? ...   04-11-2010 06:39 pm

Engine & Transmission > W58 Clutch release bearing (18 replies - 10283 views)

Thanks,  Your concerns are well founded.  Murphy's' law is not to be denied. ...   03-31-2010 11:59 am

Engine & Transmission > Rustorama (10 replies - 6266 views)

The project was just completed last week.  The Delta pans were for model years 72-74 and since mine is a 75 they required a lot ...   03-25-2010 07:21 pm

Engine & Transmission > W58 Clutch release bearing (18 replies - 10283 views)

Thanks Jim, Now all I have to do is undo the last 3 months assembly work and start over. ...   03-23-2010 03:41 pm

Engine & Transmission > W58 Clutch release bearing (18 replies - 10283 views)

I used the bearing that Colin included in kit. I'll check with the Club store or Delta for a replacement.  On another topic, I was ...   03-23-2010 03:14 pm

Engine & Transmission > W58 Clutch release bearing (18 replies - 10283 views)

My first time on the road in three years after a W58 conversion was pleasant and painful.  My fear is that I may have installed ...   03-22-2010 05:54 pm

Ignition > Mystery Wire (0 replies - 2283 views)

I have identified all the wires in the engine compartment except one that does not match the color code in the wiring diagram.  It is ...   03-03-2010 04:28 pm

Fuel Stuff > Jorge strikes again (2 replies - 4415 views)

2/17/10 update After repairing one leak another came to its funeral. Enough!!  took it to a Tank-Renu franchise in Stockton.  His assessment was that it was ...   02-17-2010 05:04 pm

Fuel Stuff > Jorge strikes again (2 replies - 4415 views)

Just in time for my start up.  After 2 years putting the mechanics together it was time to fill-r-up and let-r-rip.  I had purchased the ...   02-11-2010 12:15 am

Electrical & Instruments > Understanding alternator wiring (5 replies - 5740 views)

Thanks, it did not occur to me to look there.  Meanwhile I located a site called "British Wiring Inc" out of Pennsylvania 1-888-461-9050.  Great site.  ...   01-27-2010 04:07 pm

Electrical & Instruments > Understanding alternator wiring (5 replies - 5740 views)

It's time to atone for years of hack wiring.  After looking at wiring diagram 97020 by Delta, why is alternator output split?  1-brown (N-3-DB) to the ...   01-25-2010 09:44 pm

Engine & Transmission > hoses etc. (1 reply - 2098 views)

With the installation of a new full width sirrocco style aluminum radiator and the forward relocation of the oil cooler the hoses for the oil ...   12-27-2009 05:01 pm

Carburetors > cold air box, PCV (9 replies - 7942 views)

Group Has anyone put together a cold air box to outside air for Dellorto's? In my Dellorto conversion with K&N filters I was going to rout ...   12-20-2009 08:04 pm

Carburetors > Crankcase vent (0 replies - 2212 views)

http://www.motiontuning.com/engine-oil-catch-tank.html   This oil catch tank looks like a must have. ...   12-18-2009 04:58 pm

Engine & Transmission > Headers (5 replies - 3572 views)

Thanks for all the suggestions.  I made a 1/4" aluminum shim for the drivers side mount and it looks like that did the trick.  Since ...   12-18-2009 04:07 pm

Engine & Transmission > Headers (5 replies - 3572 views)

Knuckle is correctly oriented, I will try to space out the drivers side ...   12-17-2009 03:41 pm

Engine & Transmission > Headers (5 replies - 3572 views)

Just installed the engine in the car with JetHot coated JHPS headers and have a clearance problem with the steering shaft  It hits the headers ...   12-17-2009 03:51 am

Engine & Transmission > Conversion Components Supra Bell Housing (13 replies - 9000 views)

Kurt, Not yet, but e-mail me direct and I'll take some shots this weekend. ...   12-04-2009 02:53 pm

Engine & Transmission > Rustorama (10 replies - 6266 views)

The process started by making an exoskeleton of rectangular steel tubing that was welded to the outside rails to stabilize the monoque when thefloor pans ...   12-04-2009 01:13 am

Engine & Transmission > Conversion Components Supra Bell Housing (13 replies - 9000 views)

"Today, a date that will live in infamy"  Well not quite that bad but it has been as big a surprise.  Plug and Play.....NOT!  To verify ...   12-04-2009 01:01 am

Engine & Transmission > Conversion Components Supra Bell Housing (13 replies - 9000 views)

No joy so far,  the initial run out was .020 not .20.  Having a tough time determining the center line. ...   10-22-2009 05:44 pm

Engine & Transmission > Conversion Components Supra Bell Housing (13 replies - 9000 views)

JHRV8, A Google search found volumes 3 & 4.  Is the article faxable or pdfable? Thanks, John ...   10-21-2009 02:49 pm

Engine & Transmission > Conversion Components Supra Bell Housing (13 replies - 9000 views)

I have a CC bell housing that I have bolted to the engine.  The run out on the rear face appears to be over .20 ...   10-20-2009 10:29 pm

Engine & Transmission > Rustorama (10 replies - 6266 views)

I just received my replacement floor pans and seat rails from Delta.  Since there is virtually nothing left of the front to rear floor rail ...   07-21-2009 04:40 pm

Engine & Transmission > W58 rear transmission mount (2 replies - 2841 views)

Judson, Maybe with some luck it will all drop into place similar to what Erik Harkes has a picture of in the JHPPG site Thanks, John ...   07-15-2009 10:41 pm

Engine & Transmission > Rustorama (10 replies - 6266 views)

I'll give Jeff a call this morning.  It is in fact the ones that run front to back. My theory on the box beam literally ...   07-15-2009 03:05 pm

Engine & Transmission > Rustorama (10 replies - 6266 views)

Group, I got off lucky in the trunk, just some pitting. Flushed with success I crawled under the car and got a real shock. The floorboards ...   07-15-2009 02:48 pm

Engine & Transmission > W58 rear transmission mount (2 replies - 2841 views)

Group Colin strikes again, The CC supplied rear mount is not even close.  It's dimensionally too small and the hole pattern is wrong as well.  The design ...   07-15-2009 02:34 pm

Engine & Transmission > Engine & transmission need to go back where they came from (4 replies - 3415 views)

Looks as if a bridge crane or a fork lift would be the most painless.  Can't quite envision the placements of a typical engine hoist(s) ...   06-24-2009 02:28 pm

Engine & Transmission > Engine & transmission need to go back where they came from (4 replies - 3415 views)

Group, It's nearing the time when the power assembly with a W58 tansmission has to be installed.  From what I can understand from the forum is ...   06-24-2009 03:33 am

Suspension > Front engine mounts (6 replies - 5315 views)

The help screen does not include tips on attaching photos. Is there an easy way to resize pictures?  Any way here's the wanky unidentifiable bits. ...   06-17-2009 02:27 pm

Suspension > Front engine mounts (6 replies - 5315 views)

John, That's the logical set up but I have 2 additional 1/4" plate formed brackets that go somewhere between the mount's.  I'll post some pic's next ...   06-15-2009 12:21 am

Suspension > Front engine mounts (6 replies - 5315 views)

Good morning all, I was not present when the engine was removed from '75JH5-20175 and am having a little trouble identifying all the bits.  Neither the ...   06-12-2009 05:43 pm

Engine & Transmission > Supra conversions (6 replies - 7704 views)

Jim, Thanks for your insight. Colin supplied everything including the aluminum flywheel, clutch and tranny so I hope all the dimensions will work.  I'm not clear on ...   03-06-2009 05:46 pm

Engine & Transmission > Supra conversions (6 replies - 7704 views)

I have a Conversion Components NZ bell housing & Supra tranny that's ready to bolt up.  However I am concerned about bell housing alingnment.  Not ...   03-05-2009 05:09 pm

Miscellaneous > Distributer oil leaks (4 replies - 3682 views)

I have the results in a pdf, but am not certain how to make an attachment. ...   02-24-2009 03:25 pm

Miscellaneous > Distributer oil leaks (4 replies - 3682 views)

Just received my engine back from Huffaker after the dyno run in and wouldn't you know it it stated leaking right on the engine stand!  ...   02-23-2009 10:34 pm

Miscellaneous > Supra transmission (1 reply - 2889 views)

Hello group, I'm in the process of bolting up a Conversion Components Supra transmission. Colin must have emigrated to Australia as he has not returned my ...   02-23-2009 10:28 pm


 Current time is 11:49 pm
 First Page Previous Page  1  2 


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems