Use the search function. http://www.jensenhealey.com/forums/view_topic.php?id=154&forum_id=2 ...   01-21-2010 08:54 pm

Thanks Art, If I had to wait a whole year to drive my Jensen I would probably buy a running JH beater for the meantime. Good ...   01-13-2010 05:06 am

Hi All, The Mighty Lotus 907 roared to life today with it's new 107 cams and 104 degree pulleys! Even my wife who was interrupted while ...   01-13-2010 03:05 am

Hi Mitch, 90% of carburetor problems... My cowl seems to have been cut to allow easy removal after the steering wheel is off.  I have no idea what the ...   01-08-2010 04:40 am

The key to any airbox is to make sure there's room for the velocity stacks you are going to use. Add a minimum of 1" ...   12-21-2009 10:15 pm

Thanks Brett,  I'm concerned that the surface of the re-painted (wrinkle finish) valve cover isn't smooth enough for the small rubber surface of the washers. ...   12-16-2009 03:01 pm

What's the best way to install the cam cover washers from the club store? I don't want to damage the rubber part by tightening the bolt head ...   12-16-2009 12:15 am

Shimming new cams when there is no baseline is difficult at best. I give it a 4 vino rating per day. Start with a case ...   12-15-2009 11:21 pm

Thanks Brett! I forgot to order my xmas gift. http://www.deltamotorsports.com/ Kurt ...   12-15-2009 08:35 pm

Got a photo of the faceplate? Kurt ...   12-04-2009 03:09 am

Wanna buy some of my Special Elixer? It cures all that ails ya. If you think straight 50wt is a good idea, then go for ...   12-02-2009 01:13 am

I know of three (running) here in the San Francisco area. "New to me" Jensens show up every few weeks on Craigslist Bay Area. There ...   11-13-2009 01:12 am

Tragic. The club store sells oil pump rotors in matched sets. The tolerances and gasket thickness are critical. With the belt off, spin the accessory ...   11-08-2009 03:36 pm

The true Lotus cam has a small base circle which makes me think they were regrinds of left over E cams. Did Fred the fearless ...   11-07-2009 10:04 pm

I doubt if the aftermarket headers make 2 HP and if they do, it's at the detriment of the torque band. Unless someone does the ...   11-05-2009 04:10 am

The stock cams have a base circle of 1.210 and the 107's run about 1.140. Obviously the shims have to make up the .070 difference. ...   10-31-2009 09:28 pm

It seems funny, but the base circle on my "real" Lotus 107 cam, marked 777777, is smaller than the base circle on my other cam which ...   10-31-2009 12:47 am

Connect it to the center of the intake manifold where it bolts onto the head. Kurt ...   10-30-2009 11:28 pm

There are severaldifferent wiring diagrams for the various wiring harnesses used in the JH and GT. My diagram and in fact, my car has a ...   10-16-2009 01:04 am

That connects to the white wire that originates at the tachometer and makes the tach function. Kurt ...   10-15-2009 09:07 pm

I'm attempting to reduce the gasoline smell  in the cockpit and removed the carbs since one has an epoxy repair in the accelerator pump bowl. ...   10-15-2009 01:25 am

It seems you should contact Eurocarb at www.dellorto.com and lock in the price before the dollar slips lower. Kurt ...   10-15-2009 12:57 am

We're back home after enjoying the West Coast Nationals. Too bad so many of you missed the event, we had four days of fun. We drove ...   10-12-2009 03:37 am

I have had problems with the rotor when my MSD unit is connected. It carbon tracks down through the middle and shorts out. I purchased some ...   10-08-2009 02:54 pm

The Jensen Nationals West starts tomorrow!  Be there. Kurt ...   10-07-2009 04:47 pm

Hi Jody, Are you making the trek to the Jensen Nationals West? I'm hoping someone brings a nice JH so I don't have to vote for ...   09-25-2009 04:27 am

I'm signed up! Anyone else going? We need some Healeys to show the ground pounding Interceptors how to go around a corner! Hope to see many ...   09-23-2009 01:48 pm

The West Coast event is being held in Carson City Nevada on October 8th through 11th. The website for information, registration and accommodations is: http://www.theblandgroup.com/j2009_home.htm See you ...   08-18-2009 05:46 am

LOL! That's the first time I've heard of re-bar used in car repair!  Why not build a concrete beam? And don't forget the lally columns. Seriously, ...   07-16-2009 12:45 am

Sjensen, It's fun to learn about lubrication and the effect of viscosity on oil pressure and heat build-up. Your mechanic is technically correct but it's ...   07-14-2009 02:25 pm

Wow! Looks like a really great car! Even the close-up of the guage was JH. I love it! Kurt ...   06-30-2009 03:39 am

I think those Pertronics distributors are made for the MGB and AH Sprite. Is the advance correct for a Lotus engine? I have never read ...   06-29-2009 01:26 pm

Hi Car Collector, VDO makes a 3 1/8" tach that plugs directly into the MSD. Looks pretty good and it's super accurate. Otherwise you can order a ...   06-23-2009 01:11 pm

Hi Oscar, Does the engine spit or cough when you try to start it? Or does the starter just spin with no other noise? Kurt ...   06-15-2009 11:52 pm

To disable the temprature compensator, open the yellow cover, turn the spring over and close it up. ...   06-01-2009 03:03 am

Question 2: Get the ZS carb adjustment tool. It works through the damper on the top of the carb. Delta probably has them. ...   05-27-2009 01:18 pm

Front mid engine! Since the JH is already slightly rear heavy, will you have to add balast to the front to re-balance the car? Keep up the ...   05-27-2009 02:08 am

The 104 cams are supposed to use 104 pulleys. I'll let someone more knowledgeable comment on the cam timing. Kurt ...   05-25-2009 01:37 am

Why not just remove the bellhousing with the trans? Kurt ...   05-23-2009 12:19 am

To find Delta Motorsports click 'tech' on this page, and then 'parts'. Scroll down to Delta. It's been several years since that post. Try Ace 3135472 for an ...   05-23-2009 12:08 am