Could be the steering rack. ...   06-12-2012 04:46 am

The event organizers have added a Saturday only option for attending. Please check the website. http://jensenwest2012.com/ ...   06-06-2012 03:23 pm

I'm doing some touch-up in preparation for the Western Nationals. Anyone else planning on coming? Kurt ...   06-05-2012 03:42 pm

If the MC, rear brake cylinders and the brake servo are OK, get some Hawk 118 pads and braided brake hoses. Flush the system with Dot ...   06-05-2012 06:29 am

Wow! I saw the Lee Mueller car #43 today at Infineon Raceway (wine country, CA) sitting on the back of a Huffacker truck. There was ...   06-03-2012 04:02 am

Just to clarify, The air filter is from a 1989 Jag XJS and my airbox is an aftermarket reproduction of the Eclat unit. It sounds ...   06-01-2012 02:02 am

Bump ...   05-25-2012 01:34 pm

Holy Smoking Strombergs, I just saw this link on the Delta webpage: http://jensenwest2012.com/ I'll be there! Kurt ...   05-10-2012 12:32 am

Use a test light. Google up the procedure with points or Pertronix. ...   05-09-2012 01:03 am

An air box from the Lotus Eclat helps keep the noise slightly below ear splitting. It holds a flat panel air filter and draws cold air ...   04-21-2012 11:05 pm

I've had that happen on #4. I would re-check the timing, (12 degrees BTDC,) the float levels and the needle valves. Stick a finger in ...   04-09-2012 02:47 am

Use a course file to file down the flats on the sump plug. These were 3/4 Whitworth so most are chewed up from the old ...   04-08-2012 02:42 pm

I have one for you John. I will send a private message. Kurt ...   04-05-2012 07:19 pm

Hi Tony, Is this the 4th Jensen Healey built? ...   04-05-2012 07:11 pm

Hi Bob, The main jet and emulsion tube are not functioning in the 2- 3k range. Your issue is in the idle circuit which operates ...   04-05-2012 01:57 pm

Ha Ha! Selling anything involves the IRS. You would need a business license, federal tax I.D., liability insurance, book keeper, accoutant, etc. Then you'd have to ...   04-04-2012 01:22 am

My old SAAB got hit by a simi while it was parked. I never got a dime from their insurance. Even if you get a ...   03-27-2012 06:21 pm

Sent you a PM. Kurt ...   03-25-2012 03:01 pm

If the large flange and Lockheed brakes are there then it has potential. I remember turning the flange and counting rotation on the drive side. I ...   03-25-2012 02:48 pm

Hi Bill, A few SoCal shops are listed in the tech section: http://www.jensenhealey.com/html/repair.html Good Luck, Kurt ...   03-23-2012 03:32 am

If the budget is near $0 then your course is clear. When I was 16 years old we used to "rebuild" an engine by lapping ...   02-27-2012 06:34 pm

I guess we should be happy we have lived long enough to join the ranks of classic cars that can't find decent rubber. My Sumitomo 205/60-13 ...   02-27-2012 04:05 am

I have finally experienced the dreaded broken plastic mounting ring. Being lazy and not wanting to look for my spare I used the magic 5 ...   02-26-2012 02:20 am

Great write-up Jody. Thankfully I didn't have to go that far! ...   02-26-2012 02:02 am

Thanks Mitch! I didn't need to unscrew the nut holding the cable because it was already loose. I tightened it up and problem solved! Another 5 ...   02-25-2012 09:07 pm

My wipers failed during an foggy run to the Monterey Historics last August. Since the steering wheel is off to repair the plastic collar on ...   02-25-2012 05:13 pm

Hi Tim, if you look at the intake and exhaust markings you will see that one pulley needs to be flipped. In 110 and ...   02-25-2012 12:18 am

Thanks James! Here's some info and photos of the Lotus 909:   http://www.projectm71.com/Rudd.htm http://www.lotusbuzz.com/forums/showthread.php?t=697    ...   02-11-2012 03:25 am

Sorry it took so long Paul. Are the rest of the parts the same for either trans? Release lever, throwout bearing etc? Kurt ...   02-09-2012 09:04 pm

Hi Paul, I measured the 5 speed pivot from the inside of the bellhousing to the top of the ball on the pivot at 2.050". Perhaps ...   02-09-2012 06:54 pm

Some photos at: http://hooniverse.com/2012/02/06/sausalito-cars-and-coffee-meet/ Added Feb. 7: http://www.facebook.com/photo.php?fbid=174485322653839&set=pu.160155830753455&type=1&theater ...   02-08-2012 01:01 am

Subwoofer did it. http://www.jensenhealey.com/forums/view_topic.php?id=1209&forum_id=15&highlight=modified+sump Scroll down to the 40th post ...   02-06-2012 02:11 pm

Today I attended the first First Saturdays Cars and Coffee across from Poggio’s Restaurant in Sausilito which is just north of the Golden Gate Bridge. ...   02-04-2012 07:29 pm

It wouldn't be so bad, but not worth the money. ...   02-01-2012 01:23 am

The 907 is already substantially over square and has real issues with torque at under 3500 rpm. Boring the cylinders .060 over will only make ...   01-31-2012 01:19 am

Mine was trashed so I used a small screwdriver and a hammer. ...   01-15-2012 12:39 am

I agree Art! Maybe this should be service bulletin 12-1! Kurt ...   01-06-2012 11:49 pm

My spare aux shaft has a frozen pulley on the end of it. Good to know I'm not the only one! I was going to ...   01-04-2012 12:32 am

Welcome to the board! There's a bolt schedule somewhere. I'll have a look. Kurt       JH 13148 ...   01-04-2012 12:29 am

Hi Bob, My setup is similar to what you propose: Stock crank balanced with the stock flywheel, pressure plate, pistons and rods. 107 cams with 104 sprockets. JAE ...   12-22-2011 01:57 am