| ||||
|
Posts by subwoofer | |
---|---|
617 posts | Showing posts 201-240 of 617 |
Suspension > Fitting rear Superpro bushes (27 replies - 50601 views) And on the subject of crush tubes. They must be inserted AFTER the cotton reel is in place.
--
Joachim ... 09-21-2013 01:24 pm Suspension > Fitting rear Superpro bushes (27 replies - 50601 views) First of all, the outer shell of the old bushing must be removed, but I guess you already did that.
What I did to install ... 09-21-2013 12:29 pm Projects > The Red Fox (15 replies - 27042 views) Later spec European engine then, like mine. 9.5:1 roughly, a lot better than the Federal 8.4:1. ... 09-20-2013 09:08 pm Projects > The Red Fox (15 replies - 27042 views) SJ Sportscars sell 11:1 pistons for the 2.0, you could email them to see if they can compare pictures. You may be in luck.
--
Joachim ... 09-20-2013 06:59 pm Wheels > Wheel centre (pilot) bore? (4 replies - 12414 views) Measured the hubs tonight, as far as I can tell the required centre bore is 51.1mm (which I have seen in a list of spacers).
I ... 09-17-2013 07:36 pm Wheels > Wheel centre (pilot) bore? (4 replies - 12414 views) Does anyone know the correct centre bore? The stock wheels use the cap for centering, does anyone know the nominal measurements?
--
Joachim ... 09-16-2013 08:57 am Wheels > Stock wheel offset (19 replies - 36337 views) Dakota123 wrote:
Oh, and what is a DCA40s ECU -- I'm not familiar with it?
I am guessing it is a typo, and that he meant DTA ... 09-11-2013 07:00 pm Wheels > Stock wheel offset (19 replies - 36337 views) gmgiltd wrote:
Did you go for the Hispec kit? Front setup is excellent but the rears need longer studs and 6mm spacers to clear caliper to ... 09-11-2013 06:58 pm Ignition > Fuel Injection KIt for 907 (109 replies - 204915 views) Reviving this old thread for some possibly great news!
I have at regular intervals been nagging the people at EightStack (http://eightstack.com/) for a DCOE/DHLA sidedraft version ... 09-11-2013 07:26 am Wheels > Stock wheel offset (19 replies - 36337 views) The brakes are sitting in boxes in my garage just waiting for me to get my finger out... :-)
You are going fuel injected? I doubt ... 09-11-2013 07:19 am Wheels > Stock wheel offset (19 replies - 36337 views) Which "corner" of the wheel is problematic? If your wheels are ET15 and any of the inner corners rub, reducing ET will help.
But a ... 09-11-2013 05:48 am Wheels > Stock wheel offset (19 replies - 36337 views) Thanks, it did!
It looks like I'll be ordering ET5, then. Since 6x15 ET15 does not hit anything, neither will 7x15 ET5 - unless of ... 09-04-2013 06:15 am Wheels > Stock wheel offset (19 replies - 36337 views) What offset does your 6x15s have? It should be stamped on the rim.
--
Joachim ... 09-02-2013 06:06 am Wheels > Stock wheel offset (19 replies - 36337 views) :-)
I have been playing a bit with this one:
http://www.rimsntires.com/specs.jsp
At the moment Ms Jensen is shod with 185/70R13s on stock rims. The calculator seems to suggest ... 09-01-2013 09:18 am Wheels > Stock wheel offset (19 replies - 36337 views) The markings on the stock rims seems to suggest that the ET of the stock wheels is roughly 19mm, but measuring (with tyre mounted) seems ... 08-31-2013 06:33 pm Projects > 10628 Refresh (63 replies - 98522 views) Since you are planning on running MAF (at some point), you really should get an MS3 - the code being worked on now is MS3 ... 08-27-2013 05:38 pm Projects > 10628 Refresh (63 replies - 98522 views) Dakota123 wrote:
Megasquirt (using some fairly well-worn Dellortos as throttle bodies).
Will you be using the "TB"s dry and have a visible fuel rail, or ... 08-27-2013 06:53 am Projects > 18711 "Miss Jensen" (129 replies - 246359 views) Not too much driving this summer, been way too busy on other arenas.
But, I do get to fix the occasional something. The fire extinguisher ... 08-24-2013 07:06 pm Electrical & Instruments > Starter running via the Ghost of Lucas? (23 replies - 33179 views) Just a small heads up: I think the Flamethrower is a 12V coil, so you shouldn't have a ballast resistor in the circuit. I run ... 08-18-2013 11:26 am Fuel Stuff > Fuel type (3 replies - 10367 views) The stock JH 907 has next to no compression (8.5:1) and still fast combustion chambers, so octane rating is not likely to be an issue. ... 07-16-2013 09:08 am Electrical & Instruments > Oil Pressure/Temp T Fitting (5 replies - 10176 views) 1/8"NPT and M10x1.0 are close enough in pitch and diameter that they can be interchanged, but watch for leaks. NPT threads are conical, M threads ... 06-20-2013 05:14 am Projects > 18711 "Miss Jensen" (129 replies - 246359 views) Seconds from disaster!
One of the fittings on the oil cooler sandwich plate had loosened itself. It held up when I pulled out of the garage, ... 05-05-2013 08:50 pm Projects > 18711 "Miss Jensen" (129 replies - 246359 views) It has been quiet from me for quite a while, Megasquirting the family barge has been the priority for a while. The new loom is ... 04-26-2013 07:07 pm Ignition > Gear reduction starter (8 replies - 16551 views) My starter is on its last knees... It gave up completely two years ago, then I tore it apart, cleaned it out and bolted it ... 04-19-2013 08:56 am Ignition > Gear reduction starter (8 replies - 16551 views) Here is one that will fit (bottom of page): http://www.britishstarters.com/Lotus.html
And another one: http://classicgarage.com/eselecgerest.html
--
Joachim ... 04-18-2013 05:56 am Cooling > Heater box vacuum valve purpose (4 replies - 11884 views) VW used one in the Vanagon for the front heater, shouldn't cost more than 20-25 bucks (unless the US parts prices are insane).
--
Joachim ... 04-17-2013 04:21 pm Body & interior stuff > Custom Dashboard Project (16 replies - 25102 views) Here is how you link the photos to show in the post (hit "Quote" to see the markup:
While viewing the picture you want to post ... 04-07-2013 06:41 pm Body & interior stuff > Custom Dashboard Project (16 replies - 25102 views) There is a way around the upload size problem... Upload the pictures to (say) Photobucket and link to them with IMG tags, This is what ... 04-02-2013 07:52 pm Wheels > Correct offset or backspacing for 15x7 wheel? (2 replies - 9668 views) Did you ever get to the bottom of this, Steve? I want to order myself a set of 15x7" Revolution 5-spokes, but I have to ... 03-11-2013 08:14 pm Engine & Transmission > valve cover gasket replacement - tips for success (4 replies - 11660 views) With the rubber gaskets from the club store I have had no problems at all. Simply place them over the cam carrier, thread in the ... 03-05-2013 11:07 am Engine & Transmission > Living the dream: JH W58 5spd (40 replies - 64034 views) Jensen Healey wrote:
Sander, these cars are not museum pieces, they are meant to be driven, modified, rebuilt, raced, and ultimately, scrapped.
Whoever has the most fun ... 03-03-2013 09:02 pm Cooling > Alternate radiator sources (3 replies - 12063 views) This was sorted years ago, had a local radiator shop fit the largest core from Nissens that would fit the tanks.
--
Joachim ... 03-03-2013 08:49 pm Engine & Transmission > Idle (4 replies - 9593 views) Ms Jensen had the worst worn carbs in history, so vacuum leaks were abundant. Give the throttle axles a wiggle, there should be no radial ... 03-02-2013 12:47 pm Brakes > Metric? (8 replies - 14443 views) And I thought freight rates from the UK to Norway were bad...
I'll grab the chance while the Pound is weak to get myself a set ... 02-25-2013 09:17 pm Brakes > Metric? (8 replies - 14443 views) have you googled the part number?
I got a new master cylinder a few years back, was listed for a Land Rover IIRC. Was about £50.
--
Joachim ... 02-25-2013 07:19 pm Engine & Transmission > 40/45 DelOrtto's (6 replies - 11651 views) Back in the seventies wideband O2 sensors and data logging systems were not readily available. No one had those analytics capabilities back then, so no ... 02-25-2013 07:16 pm Electrical & Instruments > Resistor wire (4 replies - 9736 views) Mitch Ware wrote:
How many volts should be coming down the resistor wire from the tach to the coil? I've got about 2.5, that seems like ... 10-17-2012 04:39 pm Electrical & Instruments > Resistor wire (4 replies - 9736 views) chiromaster wrote:
I just pulled off the resistor wire off the + side of the coil and got 11.60v
Opening the circuit like that will always get ... 10-17-2012 04:37 pm Engine & Transmission > Foamy greenish oil (11 replies - 17215 views) Do not run it for long before checking the oil again, but if you didn't disconnect and/or empty the oil cooler and lines, you should ... 09-15-2012 06:00 pm Projects > 16173 will be entering project status... (162 replies - 258633 views) Are you sure some DPO hasn't jumped the coil+ wire from another circuit? The tach will only work if it is connected in series with ... 09-14-2012 08:57 pm | |
Current time is 11:07 am | 1 2 3 4 5 6 7 8 9 10 11 ... |